No more getting in and out of your truck to mess around with a manual slider. This hitch slides automatically to give you 14" of additional clearance for tight turns whenever you need it. Custom underbed installation kit included.
Features:
Specs:
Note: This fifth-wheel trailer hitch is not compatible with Sidewinder or Revolution king pins. Do not use any device that changes the pivot point of your trailer's king pin with this hitch.
Most often used on trucks with 6-1/2' beds, a slider helps to eliminate clearance problems during slow-speed turns. When you are towing a fifth-wheel trailer, your hitch must be situated on the cab side of your truck's rear axle. However, at slow speeds you can use a slider to slide the fifth-wheel hitch (and the trailer) toward your truck's tailgate and past the rear axle, creating enough space between the cab of your truck and the trailer to permit less-restricted turning.
Normally, you'd have to get out of your truck and pull a lever to release the slider before every turn, but what if there was an automatic system? Imagine having 14" of extra clearance while towing your fifth-wheel trailer. Now imagine having this without needing get out of the truck to move your slider. The Demco Autoslide makes this fantasy a reality. The Autoslide automatically glides back smoothly when you make a sharp turn so you can maneuver effortlessly around tight corners within campsites and parking lots.
The base of the Autoslide has a built-in rack-and-pinion gear system that operates automatically. As your truck turns, the pinion in the base also turns. This activates the rack gear, which causes the rotational force of the truck to be converted into the linear sliding action of the hitch. So, when your truck makes a sharp, slow-speed turn, the gears inside the Autoslide force the hitch head to slide down toward your truck's tailgate in a smooth, controlled motion. This way, any time that your truck turns more than 10 to 15 degrees, the Autoslide will ensure that there is enough clearance for your trailer to complete the turn as well, and it will do so without any jerking or binding.
In order for the rack-and-pinion assembly to function as designed, the pin box must be stabilized on the hitch head. Normally in a fifth-wheel hitch, the king pin moves inside of the hitch head so that the trailer can turn. With the Autoslide, the king pin remains fixed inside of the jaws of the hitch and it is the hitch head itself that turns. This is thanks to the capture brackets on the sides of the head that brace the pin box from both sides to hold it in place on top of the hitch head. This is done to ensure that there is enough resistance within the hitch when your truck turns to properly activate the rack-and-pinion gear mechanism.
To stabilize your pin box on the hitch head, simply push the capture brackets up against your pin box once the trailer is coupled and tighten the outer bolts and the inner jam nuts. The Autoslide head and brackets will fit standard pin boxes that are between 12" and 14" wide. If you have a Glide Ride, Mor Ryde, Trailair Tri Glide, Rota Flex, Lippert Road Armor, or 5th Airborne pin box, you must install a special locking plate (sold separately) as well.
When you straighten your rig out again and your trailer moves back in line, the hitch head will rotate back to center and slide back toward the cab into the straight towing position.
The single-piece, strong wraparound jaw completely surrounds your trailer's king pin for 360 degrees of contact. This wraparound jaw provides a more secure connection than standard 2-piece jaws that close in on the king pin from the sides. The increased jaw-to-king-pin contact on the Autoslide offers tighter tolerances around the king pin, which minimizes both rattle and chucking, for a smooth, quiet ride.
A 3/4" solid steel locking bar spans the area in front of the jaw. This bar provides an added barrier of protection against accidental disconnection so you can have peace of mind that your trailer is secure. The locking bar is attached to the jaw and to the spring-loaded handle. The bar automatically locks when the jaw closes around your king pin.
The double pivoting, cushioned head improves your towing experience dramatically by helping to reduce jarring and unwanted noise. Built-in pins allow the hitch head to pivot back and forth and side to side. And hooking up is easy because the hitch head will automatically pivot to the proper angle when it comes into contact with your pin box.
Three polyurethane dampeners help to cushion the movement from the pivoting head and to reduce towing noise. Two of these dampeners are built into the head assembly to cushion the head's side-to-side pivoting. The third dampener cushions the back-and-forth motion and must be installed in the hitch prior to use. Installation of this third dampener is easy - simply press the dampener up into the pre-drilled hole underneath the hitch head.
Easy Installation
The Autoslide hitch installs using the included UMS custom underbed mounting kit. The hitch comes pre-assembled for an easy installation. All you have to do is bolt on the side plates and attach the head to the hitch base.
The side plates have 2 functions. They contain the feet that fit into the receivers in your truck bed, and they allow you to raise or lower the hitch head to better match your pin box height. After you choose your desired height setting, simply bolt the side plates to the hitch base with the included hardware. Then lower the hitch into the 4 UMS receivers in your truck bed. Turn the handles to lock the feet into the receivers and secure the handles with the included safety pins. The hitch can be removed to give you full truck bed access. Simply remove the safety pins, turn the handles to unlock the feet, and lift the hitch out of the receivers.
Clearance Formula for Short Bed Trucks
Use the formula below to ensure there will be enough space between your truck cab and trailer when executing a 90-degree turn.
(A+B) - C = Clearance
A = Distance from the center of fifth-wheel hitch jaw to truck cab
B = Length of Travel (14")
C = Width of trailer divided by 2 (to get half)
For example: If the distance from the center of the hitch to the cab is 36", 36" + 22" = 58". If your fifth-wheel trailer is 102" wide, take half (51"), then plug in: 58" - 51" = 7" of clearance.
Note: At least 4 inches of clearance is recommended to safely execute a 90-degree turn.
Alternate Instructions
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the replacement side plates for the Demco Hijacker Autoslide fifth wheel trailer hitches, and this is for the underbed mount. Now this will replace the side plates that came standard with your Demco Hijacker Autoslide underbed fifth wheel trailer hitch. They are designed to bolt onto your hitch base so that you can attach your hitch to the custom underbed rails. This is designed to fit the 13,000 pound Hijacker, Part Number DM8550041. It also fits the 18,000 pound Hijacker, DM8550022, and the 21,000 pound Hijacker, DM8550037 models. This is a simple bolt-on installation to your hitch base. There are multiple rows of bolt holes on these side plates and on your hitch base, so depending how you line them out, it will let you adjust the hitch height.
The hitch height settings will go from either 15-1/2 inches to 16-3/4 and 18-1/4, so you have your choice of those three settings to get your trailer and tow vehicle as level as possible. These do have a rust-resistant black powder coat finish. They are an all-steel construction. It does include the instructions. It will include the mounting hardware, and it also includes two 1/4-inch spacers and two 3/8-inch spacers, and the spacers are used for adjusting your hitch mount with the bed pockets of your truck, and this part is made in the U.S.A. The way that these would open up is you just pull the clip, pull the pin out, and you can see each one of these will rotate out, and when you rotate those out, it will let you drop it into your underbed mount, and then once there, you just turn this back in to lock it, and then put your clip right through there just like that. This part is made in the U.S.A. That should do it for the review of the replacement side plates for Demco Hijacker Autoslide fifth wheel trailer hitches with the underbed mount..
After a year, I still like my Demco autoslide. It works great. I have pulled my trailer quite a few times and have had no issues at all. I know quite a few people that pull 5th wheels and one actually went out and purchased a autoslide after watching mine work.
This hitch has been used daily since i purchased it. I deliver fifth wheel travel trailers all over the country. This hitch has worked flawlessly from day one. This hitch is one of the only products that I've ever bought that is exactly what it was described to be. Im not one to do reviews, so the fact that im doing this one , in itself, says a lot about the quality of your product. The design and looks are much better than any other hitch ive seen. It just looks better in the truck bed than others do.
Instructions left alittle to interpretation when it came to hitch height in the bed of the truck. For a f350 super duty it is the medium set up. Save you some time and effort. Other then that it looks great and will be testing it out this weekend.
Hitch works great. Had some issues using it when I first got it with putting the pin to lock down the handle but its worked much better lately. The hitch is heavy so I leave it in the back of the truck. Wish I could remove it so it doesn't get weathered.
Hitch looks great and functions great as well. Installation could’ve been smoother due to the installation instruction measurements being slightly off. Look at finding hole caps that are 3” instead of two and drilling the larger hole.
great hitch for my customers new truck to pull his new Durango 5th wheel!
Fast Delivery as well
Always RV
Mesa Az
Hitch sucks pain in the assembly to connect and disconnect.
Great functional hitch. Poor powdercoating though (mostly flaking off) with quite a bit of rust after only a year.
Worked out great. I used the hitch for my camper right after I installed it. However, I did break one of the bolts when installing it, which is OK. I just switched to grade 8 bolts which is better anyways. I love the fact that Demco hitch unlocks when you pull the lever regardless of weight on it. Compared to my previous Mopar hitch you had to get at the right weight pressure to unlock it.
Well built fifth wheel hitch. Haven't got a chance to tow our new Montana High Country 295RL. But I know a guy that has towed his fifth wheel with this same hitch. I'm sure this 18K hitch will be excellent! Or I wouldn't have bought it. I recommend e trailer for everything.
Has to do a little assembly, really easy. Tows super nice, when turning does move towards the back. You’ll need to adjust the guides for the fifth wheel.
Demco auto slide hitch works very well with my crew cab short bed Ram. Fits under my tonneau cover nicely. Trouble free thus far. Had to purchase a Demco plate for the camper to make the Rhino box hitch work. etrailer personnel were great in helping ensure I had the right products and kept me well informed of shipping dates.
Love this hitch. While it is heavy it provides the stability and auto slide capability that I need to comfortably drive my 5th wheel thousands of miles. I have never had my 5th wheel contact my cab no matter how tight I turn.
This product definitely gives me more availability for tighter turns that I was looking for. Second trip we took one of the pins popped out of the puck locking mechanism. Our last trip to Wyoming the spring pin that holds the head onto the frame was laying in my pick up box, bought a new spring pin clip that’s a little tighter, that seem to fix that issue. It would be good practice to go over the entire hitch of all mechanisms latches and secure pins before traveling. Seems with the moving and shaking, they may have a tendency to loosen a bit overtime.
Item works exactly as described. I have a shortbed (6.5') Ford F350. Probably towed our 5th wheeler 5000+ miles with no problem. Then last year it happened! We were making a sharp turn in an uneven lot and POW, the 5vr hit the rear window and it exploded. After that I became gun shy about turning with the 5vr attached so I started looking at sliding hitches. A slider that you had to get out and unlatch to make work, didn't make sense to me. At what point do you get out? So, an auto slider hitch was purchased. Now when I get to a certain degree turn the auto-slide hitch moves back in its carriage and then auto-slides to the normal location once straightened out. Not gun shy anymore.
Pro:
Well packaged
Well made
Easy install
It WORKS.
Cons:
Price
Very heavy
Some clunking after it straightens out from a turn
A very nice hitch. If you have a bed carpet or a bed liner it may require Un shimming the locking pins. I have a bed carpet and I had to stand on the back corners to get the pins to engage the bed pucks. Not really a big deal. It is very heavy so I assembled it in the bed of the truck. I would highly NOT recommend doing it this way except if you are by yourself. Get a chain hoist or maybe an engine hoist because it is very heavy as an assembled unit. It is flawless in its operation. Very well made. I am very happy with it.
Very happy with my Demco Autoslide hitch after one year. We pull a Montana 3120 35 ft 5th wheel with a 2019 Ford F-350 short bed. Took a month long 6,000 mile trip from Colorado to New England/Canada this Summer. Lots of hilly/curvy roads and some remote campgrounds with tight corners and some near 80 degree back ins. Never came close to trailer contacting the truck. I’ve had no jerking or other issues when turning or stoping/starting. Works great. The only drawback is there isn’t much room for error when you back up to hook up the trailer, so it takes a little practice to get used to correctly lining up your Demco Hitch to the trailer. The first couple of trips, it took me 3 or 4 attempts to properly line it up. No longer an issue for me after a few trips and you get used to the angles. It weighs about 300 pounds. I got a small chain hoist which I installed in my garage rafters and easily lift the hitch in and out of my truck and just let it hang front he rafters until I need to use it.
The Demco Auto slide takes the worry out of towing my fifth wheel trailer with a short bed F-350. I have had no problems with backing into tight camping spots. And since everything is automatic I have one less thing to worry about while traveling with a fifth wheel.
The only problem is that it is a little on the heavy side, so I just leave it in the truck when not towing. Problem solved.
I am extremely happy with the product.
Do you have a question about this 5th Wheel Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.