CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" - Qty 1
(319 reviews)
Price: $3.48
CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" - Qty 1
Item # CE11051
Retail:$10.70
Our Price: $3.48
You Save: 67%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (319)
- Q & A (0)
- Videos (2)
- Photos
CE Smith Accessories and Parts - CE11051
- Boat Trailer Wheels
- Golf Cart Tires and Wheels
- Trailer Tires and Wheels
- Wheel Lug Nut
- Hex Nut
- 60-Degree Cone
- CE Smith
- 1/2 Inch Wheel Bolt
- Zinc-Plated Steel
- 13/16 Inch Outer Diameter
Secure a wheel to your trailer with the help of this lug nut. It features zinc-plated steel construction and fits a 1/2" wheel stud.
Features:
- Lug nut holds mounted trailer wheel in place
- Zinc-plated steel construction is sturdy, rust resistant and long-lasting
- Made in USA
Specs:
- Quantity: 1 lug nut
- Fits 1/2"-20 wheel studs
- 60-Degree coned (standard)
- Threads per inch: 20
11051 Zinc-Plated Steel Trailer Wheel Replacement Lug Nut by CE Smith - 1/2"
Video of CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" - Qty 1
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for CE Smith Trailer Wheel Lug Nut Review
AJ: What's up, everybody It's AJ with etrailer.com. Today we're going to be looking at this lug nut from C.E. Smith. This lug nut fits half inch bolts and it has 20 threads per inches. I'm sure most of you know what a lug nut is and what it's for, because you probably already need one, but we're going to show you an example on this U-bolt spare tire carrier. Most of the time they don't come with a lug nut, so you'd have to get one separate.
These are the ones for you.You see, you just put it on there and tighten it down. Make sure that the small part here at the bottom, the 60 degree cone part goes towards the tire. That just helps it get into the lug nut hole here and really tighten it down. With them tightened down by hand, we're going to use the wrenches, get a couple more turns on there just to make sure that the tire's not going anywhere. Do this one another turn.
There.Keep in mind, these come in a quantity of one. So if you're going to use it on a spare tire carrier like we showed you inside, you're only going to need two of these. If you're going to put a tire on a trailer like here, you're going to need five of them. There's many different uses for the lug nut, I'm not going to rattle off a bunch of them because you probably know exactly what you need this for, and you just need to order it. So that does it for our look at the C.E.
Smith lug net..
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
- Product did not meet expectations
Customer Reviews
CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" - Qty 1 - CE11051
Average Customer Rating: 4.7 out of 5 stars (319 Customer Reviews)
Secure a wheel to your trailer with the help of this lug nut. It features zinc-plated steel construction and fits a 1/2" wheel stud.by: Butch05/17/2023
Neither of these products will work for my application. I needed threaded studs, both ends as well as nuts with shoulder washers, not acorn.
by: Allen09/11/2023
Received the hubs very quickly. They were well greesed and ready to go. They look well machined. I did have one lug nut that had something wrong with the threads. I might could have used it, but since it would not thread on by hand I did not want to try it since it might damage the stud. I went on line and did a chat with etrailer. Thier customer service is top rated. They shipped me out another lug nut. This is why I do business with etrailer. They understand the needs of the customer and understand the products they sell.
I installed the hubs this weekend and took the trailer for a test pull. Needed to adjust the brakes up a little, but all was well.
by: Mark 11/20/2023
They're lug nuts. They fit.
by: Jesse 07/21/2023
Bought these while swapping tires on my enclosed trailer and figured I'd go ahead and replace the nuts. Worked great, aside from the some wear on the bolt threads (another project).
by: John 09/28/2023
This is a classic zinc plated lug nut which is remarkably difficult to find at retail locations in my area.
by: Edward 09/14/2023
Ahhh lugnuts how i love playing with my lugnuts.
by: Scott06/20/2023
These lug nuts were a perfect match to the ones I was replacing. Price was reasonable as well.
by: Jarrod 06/05/2023
Excellent service. Fast shipping. Perfect, rust-free direct and inexpensive replacement for the lug nuts on my utility trailer.
by: Bret07/19/2023
Wheel just as described and matches the factory wheels on my Shorelander Trailer with Lund Pro-V.
by: Jonathan11/09/2022
The U bolt spare tire carrier was perfect and just what I ordered. The perfect size of 9" just as I needed. But unfortunately I didn't receive the two 1/2" lug nuts as I ordered and paid for. Without those I really can't use this product. I am very unhappy that I paid for something and didn't receive it. I have tried to call customer service and cannot actually find a number to talk with anyone. I will try and email customer service and go from there. If they make this right I will update from there. But like previous reviews, I didn't receive my lug nuts as ordered also.
Jenny N.
11/14/2022
We want you to receive your full order. I will have our Customer Service team reach out to you. Our phone number can be found at the top of the home page and on the customer service page.
by: Rod06/13/2022
Parts fit great. It took me awhile searching on the sight to make sure I was getting the correct part. I was also concerned when I saw that a quantity of 1 had been shipped when I had ordered 2.I called to confirm that I was getting 2 of each item and I was on hold for 18 minutes before getting a response. Once someone answered the phone they were knowledge and professional.
Rod
6/14/2023
The nuts are holding up great.
by: Michael 11/16/2023
Fit right. It now I have to replace them all since these are nice and shiny and my old ones are black. Ha
by: Joseph02/08/2023
etrailer is a first class company. Very knowledgeable extremally efficient and helped me get the best product for the price. Shipped when then said it would and came in when I needed it. I have made them my preferred vender for my trailer and towing parts. Thank you Meghan for your help.
by: Brian05/05/2023
Bought to hold on a spare tire. Does the job.
by: Mark09/15/2020
The new lug nuts worked great on my trailer. Perfect match for my new wheels / tires. Five [stars]
by: Jeffrey 11/09/2023
Worked as advertised
by: Mike 10/13/2023
Worked like it should.
by: David 01/28/2023
perfect fit for my standard 6' by 14' trailer on the tire lug
by: Delton08/12/2023
Worked perfectly as expected. Customer service was excellent and delivery was quicker than expected.
by: Ed11/04/2022
Lug nuts and some wheel studs. Hard to screw that up. What else can I say other than they were new and fit correctly. Good job!
by: Dave 07/22/2023
Always the right order, on time. Great service!
by: John02/26/2021
My original steel lug nuts were rusty. Haulmark does not sell lug nuts, so etrailer was the place to go to get zinc plated lug nuts that are unlikely to develop rust. Mine were 18 years old, so not a surprise they had developed rust.
John
2/27/2022
chrome nuts were a big upgrade from rusty stell nuts
by: Raheel09/30/2022
Its not deliver how is promise very poor customer service I will not recommend anybody buy from you guys customer service was very bad the person took my order I call several time to locate my order and she’s never available other person get my call and she was extremely unprofessional and rude I’m returning everything back to them they charge me UPS ground service and they promised me the date my My merchandise don’t come on time and it’s the wrong merchandise fox if you’re buying to them they are very sweet in the beginning on the sale after that has become very horrible customer service do not recommend it again do not recommend
by: David 09/08/2022
After a year of use and sitting out in the weather, the Zinc plated Lug nuts are holding up fine without any sign of rust or degrading. Good product and I would recommend to anyone.
by: Todd 01/22/2023
As usual with etrailer… great price, product and arrived early. Thank you!!
25
319
Show More Reviews
See what our Experts say about this CE Smith Accessories and Parts
- Is 20 Threads Per Inch a Fine Thread Pitch for a 1/2 inch Wheel Bolt20 threads per inch would be a fine thread pitch on a 1/2 inch wheel bolt like the part # CE11051. A coarse thread would be 14 threads per inch.
view full answer... - How to Figure Out Correct Replacement Hubs for a 1980 Jayco Jay Flight 8I do have a way for you to find out what equipment you will need. Finding any information for a 1980s trailer will be pretty much impossible (as you have found) unless you have the owner's manual with a parts list. Manufacturers typically don't keep information for older trailers on file, but it never hurts to check with them if nothing else can be done. You can pull your hub and see what the part numbers are on the bearings and grease seal to find out what the correct replacement would...
view full answer...
- Lug Nut Torque Range for 1/2-Inch Wheel Studs and Steel Trailer WheelsThe correct lug nut torque for any given trailer wheel depends on a few things. You can refer to the linked diagram that provides a range of values depending on the factors like stud size and wheel material. For 1/2-inch studs with coned lug nuts for steel wheels the torque range is 90- to 120-ft-lbs.
view full answer...
- Socket Size Needed for CE Smith Trailer Wheel Lug NutThe CE Smith Trailer Wheel Lug Nut # CE11051 uses a 13/16 inch socket. I went out the warehouse and confirmed that the 13/16 inch socket is correct for this lug nut.
view full answer... - Could Trailer Lug Nuts be Used on Older VehicleIn most cases they are they same, but you have to find out what angle of cone you have. If you have the standard 60 degree cone then the # CE11051 would technically work just fine.
view full answer... - Most Common Lug Nut Size For Smaller TrailersThe most common lug nut we find on trailers is 1/2 Inch Lug Nuts like the SE Smith # CE11051 you were looking at. Since it is a small trailer, I would presume that this is the lug nut you need. If you can find out the weight capacity of the trailer, we can confirm exactly what lug nuts you need.
view full answer... - What Size Lug Nuts are Used for a 5 on 4-1/2" Bolt PatternA 5 on 4-1/2" bolt pattern on a trailer wheel will use a 1/2" bolt with a 60-degree cone. I have linked our selection of bolts that meets this criteria for you to filter through. One of the most popular is the CE Smith Trailer Wheel Lug Nut # CE11051 which is zinc-plated steel made right here in the USA.
view full answer... - How To Determine Torque Setting For Lug Nuts On Disc Brake HubI have attached a chart that has the torque settings for lug nuts. The torque settings are based on the lug size, type, wheel size, and material. The 6 marks you have on the lug means it is a grade 8 high strength lug bolt. For example, for a 15-inch steel wheel secured with a 1/2-inch lug bolt use a torque range of 90 to 120-ft-lbs.
view full answer...
- Size of Socket Needed for the CE Smith Trailer Wheel Lug Nut # CE11051 I went out and grabbed a CE Smith Trailer Wheel Lug Nut # CE11051 from our warehouse to measure it and found that it would take a 13/16 inch socket to tighten/loosen it.
view full answer... - Do Trailer and Vehicle Lug Nuts in 1/2x20 Size Use the Same Cone AngleYes, the CE Smith Trailer Wheel Lug Nut # CE11051 that you referenced is a 1/2 inch x 20 lug nut that uses the same standard cone angle of 60 degrees which vehicles use as well.
view full answer... - Recommended Lug Nuts For 2002 Yacht Club M20 Motorcycle TrailerThe lug nuts you need for your Yacht club M20 motorcycle trailer are 1/2 inch fine thread. My contact told me that the wheel bolt pattern is a 5 on 4-1/2 inch if you ever need to replace the wheels on the trailer. The lug nut I recommend for your trailer are part # CE11051. I have attached a link to a product review video you can check out.
view full answer... - Replacing ST175/80R13 Special Trailer Tires and Wheels on Boat TrailerYour ST175/80R13 trailer tires can be mounted on three widths of 13-inch rim: 4-1/2, 5 or 5-1/2-inch. If your current tires are new enough and in good enough shape to justify re-mounting them (as opposed to just buying complete new wheels/tires) then you will just need to use new valve stems. Trailer tires should be replaced at least every 6 years, regardless of mileage. Lugs nuts do not necessarily have to be replaced but the specific wheel you choose might make new ones a good idea if...
view full answer... - Does Going from Steel to Aluminum Wheel Require Different Lug NutsSince you have 14 inch trailer wheel the studs of your hubs would be 1/2 inch which is a very common lug nut size. You don't actually have to switch lug nuts to go from steel to aluminum wheels though (or vice versa). Aluminum wheels have steel inserts for the flange so there won't be an issue with dissimilar metals.
view full answer... - Availability of 1/2-Inch Hex Nut with 13/16-Inch Wrench FlatsWe do offer a fine-thread 1/2-inch hex nut, part # CE11051, which is a trailer wheel lug nut with a 60-degree coned profile on the outside surface. The rear surface is flat. This item is uncoated steel so you can paint it black if you wish. Take care to keep paint out of the threads. It takes a wrench size of 13/16ths-inch.
view full answer... - Lug Nuts For Hub on Dexter 3,500 lb AxleA Dexter 3,500 lb axle will have a hub that uses 1/2" lug nuts, so the correct part is the CE Smith Trailer Wheel Lug Nut - Zinc-Plated Steel - 1/2" # CE11051.
view full answer... - Recommended Wheel Stud For Dexter HubThe Wheel Stud I recommend for you is part # 7-122. I have attached a drawing that has all of the dimensions for the stud you can check out. Since you are replacing the studs you may be interested in going with new lug nuts as well. I recommend part # CE11051. These are zinc-plated steel and are sold individually.
view full answer...
- Proper Centering of New Trailer Wheel Whose Pilot Hole is Larger Than Original WheelsYou were given some correct information. The new trailer wheels you purchased that have a larger pilot hole will still be compatible with your hubs in terms of being properly centered. The key is indeed the coned lug bolts, such as # RG02-020. These will automatically center the wheel on the hub as they are tightened, as will coned lug nuts such as # CE11051. The larger pilot hole does not matter for alignment. However, since your wheel has a larger pilot hole diameter this means that...
view full answer... - Can Trailer Wheel with 1/2"-20 Wheel Bolt Holes Mount to Hub with M12 Studs Yes, it is perfectly okay to use a trailer wheel like the Dexstar Steel Mini Mod # AM20242 you were looking at that features 1/2"-20 wheel bolt holes on a hub with M12 studs. The M12 studs are just slightly smaller in diameter but as long as you use lug nuts that have a 60 degree bevel (like part # CE11051) to match the wheel bevel this isn't an issue.
view full answer... - Typical Trailer Lug Nut Diameter and Thread PitchTrailer wheel lug nuts that are 1/2-inch inside diameter typically have a 20-TPI thread pitch (20 threads per inch). Most lug nuts also use a 60-degree-coned profile like # CE11051, but a 90-degree like # STN569 is also available for 9/16-inch studs. All lug nuts we offer are displayed on the linked page. I also linked our main page for all wheel accessory items.
view full answer... - Availability of Replacement Hardware for MaxxTow Spare Tire CarrierMaxxTow doesn't have replacement 1/2" carriage bolts for the Spare Tire Carrier MT70214 but you can use the CE Smith 1/2" Lug Nut # CE11051 as a replacement for the lug nuts on the carrier. The carriage bolts will need to be sourced locally.
view full answer... - What Degree Lug Nut Should be Used with Kenda Karrier ST235/85R16 Radial Trailer Tire with WheelThe Kenda Karrier ST235/85R16 Radial Trailer Tire with 16" Black Mod Wheel # AM35010 uses lug nuts that have a 60 degree cone shape like the part # CE11051.
view full answer... - Lug Nut Recommendation for 175/80R13 Spare on Vintage Franklin Travel TrailerI received a photo of your original 1/2-20 lug nut. I did not receive a photo of your steel rim/spare tire. That being said, it looks like the type of lug nuts you were using are mainly used on specialty wheels, which would explain why they won't work on your new/standard trailer wheel. For a standard open ended 60 degree coned lug nut you can use # CE11051. This fits 1/2-20 wheel studs which is what you need.
view full answer...
- Lug Nut Size Needed for 1969 Mobile Scout Tandem Axle Travel TrailerWe have no way to look up details on a small part like the lug nut used on a trailer that was made in 1969 and for a vintage camper like yours it is entirely possible that 50 years later it may no longer have the original axles and hubs on it. However, based on the 4K axle rating you mentioned you most likely have 1/2-inch wheel studs that will use a 60-degree lug nut like # CE11051.
view full answer... - Screw in Trailer Hub Wheel Stud 1/2 Inch to Replace Coarse Thread Lug BoltsWhat you are seeking is the Trailer Hub Wheel Stud, Screw-In, 1/2" x 2" # 25-51. Then you can use Trailer Wheel Lug Nut - 1/2" # CE11051 as you mentioned.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Installed by:
Andrew K
Installed by:
Jeff D
Written by:
David L
Updated by:
Adele M
Video Edited:
Dustin K
Video by:
Aidan B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
5/22/2023
I am sorry that we did not have what you are looking for. Based on your pictures we carry similar drive-in studs part # 25-53 however they are not quite the measurements shown in the picture. It is a one-half diameter stud with an over length of two inches, I checked and we do not have the type of shoulder bolts you are looking for.