To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Replace the cable that attaches to the actuating cylinder on your Demco Stay-IN-Play Duo or Air Force One supplemental braking system.
Features:
Fits:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everybody, Ryan here at etrailer. Today, we're going to be checking out and walking you through how to replace the actuator cylinder cable for the Demco air force one, and Stay-n-Play supplemental braking systems. So when it comes to anything mechanical, you know, stuff does happen and you do have some failure points. And uh that's exactly what happened with our uh customers here today. The cable, uh you know, it, honestly, it had been cut from a shop, kind of getting them out of a pen, trying to deactivate the system. The braking system was having some issues.
Um, ton of different other ways around it, but that's what they did. So, we needed a new cable. Obviously you can't use it. But sometimes these do fail for other reasons, which we'll get to a little bit later on, but you know, if you, if you'd like to tinker on things and you're relatively handy, um you know, a lot of times you can get away with just replacing that failed part and not having to buy a whole new actuator cylinder. Um, you know, if you don't feel like messing with the cable, you can pick up the cylinders that are already pre-built and everything.
But you know, if you want to save a few bucks, a lot of times you can uh just replace what needs fixing and that's exactly what we did here today. Cause the cylinder and everything else was fine. So this is pretty straightforward. Not much to it. This is going to work with the cylinders from the Demco Stay-N-Play supplemental braking system, as well as the air force one supplemental braking systems.
And that holds true for those of you that have the coach link monitors as well. It doesn't matter, same cylinder. So honestly, if your cylinder looks like this, the majority of them that I've seen are pretty much identical. Uh you'll be in pretty good shape. With that said, once I had this one apart, I did notice that the one that was originally in it looked a little different at the top there.
There- it has a little brass piece or it looks to be brass. And at the bottom, I actually had to cut off a c-clip, or a snap ring type deal to get this one out. Um, if yours looks like that, the new one will still work. Um and actually the new one actually had a little bit of a better design in my opinion. Instead of a snap ring, it used on an alan or a hex head nut there, to make it easier to disassemble. And it just had a better attachment point here in this brass collar type deal going on. So, just something I wanted to mention, and if yours looks a little bit different, chances are still really good, uh, this new replacement is going to work. So, now that we uh kind of checked this out, why don't we go ahead and put the new cable in So it looks like at the top here, this uh brass colored part, it's got a couple of openings there. I'm gonna use a pair of snap ring pliers to unscrew this. You could probably just use a regular pair of pliers and grab it around the sides too. It's probably isn't in there super tight. But we're going to unscrew this and see what lies beneath. It should be a relatively straightforward process here if I can get these pliers to work right. So go ahead, get this unscrewed. And I do suggest doing this on a table or a bench, that way we can kind of set everything to the side, kind of keep track of everything in here. So with that off, it looks like this piece can probably come off. It is not wanting to though. Let me see if I can't maybe try to loosen it up. So I think what the issue is, or one of the issues, is that the cable's kind of jammed in there. There we go! So we get that out, trying to work all this out. And once I get all this pulled out, we can kind of check it out and go from there. So we got all that pulled out and if he continued to try to pull it forward, it just stops. So it looks like if we remove our fitting here, using a seven sixteenths, if you remove that fitting, I'm thinking there'll be a part underneath there. So we'll push our cable up, and you try to pull it all the way out. It's stopping too. So, think what we have to do at the end here, there's an itty bitty snap ring, this little black ring there. And I feel like we need to get that off. That way we can just pull it out this way. So this thing is really, really small here. So I'll do my best. Kept on trying to get that snap ring off, to no uh success there. Kind of tired around and messing with it and since we're not reusing any of this anyway, uh I'm just going to get the show on the road. So I'm bringing out a Dremmel tool and I'm just going to cut this end off. So with that cut off, now, we should be able to grab everything here and get it pulled out. So with that piece removed out of there, what cha want to do is inspect the boar, your cylinder there, uh you know, make sure it's clean, lubricated, and so on. Ours is actually in pretty good shape. And on this piece might not be a bad idea just to take some type of, of- oil. You know, I just took a little uh oil and super light coating on it, um to keep things moving, and now we can take this, feed the cable on through, and pull that pull it through there. And we'll take our air fitting and get that re-installed in the back of it. So with that deal done, all that's left to do is transfer this piece, slide that on, thread it down. Like I said, we don't have to crank these down just get 'em snug. So that's really all there is to it there. Uh what I'm gonna do since I'm- while I'm at it, is take our old anchor, and get this swapped over to our new cable. That way we're ready to ready to ready to roll here whenever uh- you go to re-install this inside of our vehicle. And that'll finish up our look at of the replacement actuator cylinder cable, for the Demco Stay-n-Play and air force one supplemental braking systems..
Average Customer Rating: 4.9 out of 5 stars (34 Customer Reviews)
Replace the cable that attaches to the actuating cylinder on your Demco Stay-IN-Play Duo or Air Force One supplemental braking system.I always enjoy shopping with etrailer. We were in a bind because we’re on the road and only at one place for a few days. So instead of ordering online, I called and had the pleasure of working with Will. He was super pleasant, very helpful And expedited our order to ship in the best way. We got it on time, installed, and we can continue our journey. Thank you!
The replacement was excellent, with straightforward installation instructions. It's essential for owners to inspect this cable annually. As it turns out, mine was not installed properly; there was no slack left in the cable, leading to its eventual breakage.
Great service! Arrived on time and watched etrailer video on how to install the part.smooth and hassle-free!
The replacement cable saves a lot of money compared to replacing the entire cylinder
The part came on time, fit as advertised, and has worked great ever since. Etrailer is a pleasure to do business with.
Always great service with e trailer thank you! Got our toad back on the road
Very prompt delivery. and well packaged.
Loren
1/27/2024
Seems to be a quality product. The cable is still in good shape and not frayed..
SHIPPERS FAULT BOX WAS BROKE OPEN
CUSTOMER HAD TO FIND 1 AT ANOTHER LOCATION, THEY WERE IN TRANSIT
Part fits perfectly with no hassles fast shipping great video helps putting in the Part
Friendly competition service and prompt delivery.
I have purchased everything i have related to camper, motor home, towing and also my Demco stayinplay brake system that I have installed on my 1989 Ford bronco 2. I’ve had nothing but excellent service, tech advise, and timely delivery. Thanks etrailer.
All my experience with etrailer has been excellent. From the products they sell, shipping, customer service, it's all top shelf. Thank you for all you do.
Always get outstanding service
Received this in a timely fashion.
I was a little worried as this product looks slightly different than what I had but they had a great video explaining that shouldn’t be a problem, parts arrived everything installed as the video described.
Perfect replacement part and saves a lot of money vs. buying the whole cylinder.
Great service very helpful exact fit on parts
Mario
3/4/2024
The cylinder cable is still working great and holding strong since replacing it 1year ago. We traveled continually for 4 months and had no issues with the Demco braking system or the cable.
I was happy to find the repair part available. Price was acceptable, shipping went well and repair was simple.
You all delivered this part while I was on vacation. Sent it to me at an RV resort. It was waiting for me at the front desk on my arrival. Great job!! I really appreciate it .
Customer service was excellent it helping to expedite my order... thank you Ashley!
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Larry
6/3/2024
Product is still working as advertised!