Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Right Hand - 6,000 lbs

See what our Experts say about this Dexter Accessories and Parts

• Center Hole Diameter of Brake Assembly 23-106-09
  The center hole of the brake assemblies # 23-105-09 and # 23-106-09 measures 3-3/16 inches across. The kit for both of these is the part # 23-105-106-09 that you referenced.
  view full answer...
• Available 12 x 2-Inch 6K-Rated Electric Trailer Brakes with 4-Bolt Mounting Pattern
  All of our 12 x 2-inch 6K-rated electric trailer brakes are shown on the linked page. Most of these use the 5-bolt mounting pattern but a few Dexter products include holes for BOTH bolt patterns, both 5-bolt and the 4-bolt Hayes/AL-KO pattern, parts # 23-105-09 (left) and # 23-106-09 (right). We also offer them as a set, part # 23-105-106-09.
  view full answer...
• Which Brake Assemblies for 2002 Vintage 28 Ft Enclosed Trailer
  The numbers you provided don't correspond with any brake assemblies we offer, so I did a Google search on them and found no results. To find the correct brake assembly, you'll need to know the inside diameter and depth of the brake drum. You'll need the capacity of the axle, and you'll also need to match up the bolt pattern of the brake assembly to that of the brake mounting flange welded on to the axle. For instance, the # 23-106-09 brake assembly fits a 12 inch diameter by 2 inch deep...
  view full answer...
  
• When Should I Replace My Brakes On The Dexter Electronic Brake Assembly # 23-106?
  I reached out to Dexter about your specific question concerning your brakes # 23-106-09. A simple visual inspection of your brake linings will tell if they are usable. Replacement is necessary if the lining is worn to 1/16" or less. Shoes contaminated with grease or oil, or abnormally scored or gouged should also be replaced. Hairline heat cracks are normal in bonded linings and should not be cause for concern. When replacement is necessary, it is important to replace both shoes on each...
  view full answer...
• How To Determine if Dexter 12x2 Electric Brake Assembly # 23-106-09 Will Fit 1982 Silver Streak RV
  The same answer would apply. The brake assembly # 23-106-09 is designed to fit a Hayes/AL-KO or Dexter axle with either the 4-bolt or 5-bolt mounting flange. These are 12 x 2 inch brakes. To measure the drum you will measure the inside diameter. It should be 12 inches. Then measure either the width of the old pad or the width of the surface it would contact on the inside of the drum. That should be 2 inches. These brakes are designed for 6,000 pound axles but could also be used on a 5,200...
  view full answer...
• Replacement Electric Brakes for a 1980 Dugan Stock Trailer
  The brakes in the picture look like they have the offset 4 bolt pattern that Hayes/AL-KO brakes use. On that bolt pattern the top two holes are spaced further apart than the bottom 2 holes. If they are 12 x 2 inch brakes then we have some with that bolt pattern: # 23-106-09 for the right side and # 23-105-09 for the left. We do not have just the magnets for your existing brakes though.
  view full answer...
• 4-Hole Spacing Measurements on Dexter 12 x 2 Inch Electric Trailer Brake Assemblies
  The mounting holes (4 hole pattern) on Dexter brake assembly, # 23-106-09, are 3.09 inches on center for the top two holes and 2.55 inches apart on center for the bottom 2 holes. Top to bottom they are 3.40 inches apart on center. The holes can accommodate a 7/16 inch bolt size. So it appears to be a match with the mounting plate you have. The matching left hand assembly is # 23-105-09.
  view full answer...
• 12 Inch x 2 Inch Electric Brake Assembly with 4-Bolt or Standard 5-Bolt Flange
  The bolt hole patterns for # 185150 and # 185100 did change at the end of 2015. You'll need to pick up the following 12" X 2" brake assemblies which have the 4-bolt pattern that you are looking for as well as the standard 5-bolt flanges. Left side # 23-105-09 Right side # 23-106-09 Please check out the attached demonstration videos.
  view full answer...
• AL-KO 6k Brake Assembly Recommendation with Offset 4 Bolt Mounting Pattern
  We have a set of brake assemblies fit to replace your 12 inch x 2 inch AL-KO electric brakes. The Dexter # 23-105-09 left-hand side, # 23-106-09 right-hand side. These brake assemblies are rated for 6,000 pounds per pair like your axle and have the offset 4 bolt mounting pattern. The # 23-105-09 and # 23-106-09 will mount on either the 4-bolt AL-KO/Hayes or standard 5-bolt flange.
  view full answer...
  
• Will Dexter Brake Assemblies 23-105 and 23-106 Replace Kelsey Hayes RH602041 LH602042
  Most likely the # 23-105-09 and # 23-106-09 would work well for you, but you need to verify one more thing. Does the current brake assembly you have attach to the axle with 5 nuts? If so, then you have the standard bolt mounting pattern these two would fit well. These are 6k capacity assemblies as well.
  view full answer...
• Replacement Brake Assemblies For Al-KO Or Hayes 4-Bolt Flange
  The closest brake assemblies we offer to the dimensions you said you have are part # 23-105-09 for the left hand, and # 23-106-09 for the right. The 4-hole bolt pattern is 3-1/4 inches for the top two holes, 2-1/2 inches for the lower two holes and the distance top to bottom is 3-3/8 inches. I know the measurements are off by 1/8 inch versus your measurements but I am sure these are what you are looking for. These are designed for either AL-KO/Hayes 4-bolt or standard 5-bolt flange and...
  view full answer...
• How to Determine if Trailer Brake Assemblies 23-106-09/23-105-09 Fit Trailer
  I can help you find the right assemblies, but I do not know exactly which ones you have on your trailer. To pick out the correct brake assemblies for your trailer you need to know a few things. You will want to measure the inner diameter of your hub/drums and the depth of the drums to determine what brake assembly dimensions you need. For example the part # 23-105-09 is a 12 inch by inch thick brake assembly. You also want to determine what the bolt pattern is of your assembly mounting...
  view full answer...
  
• Need 12 x 2-Inch Electric Trailer Brakes with 4-Bolt Mounting Flange
  We do offer 12 x 2-inch electric brake assemblies with a 4-bolt mounting flange. Dexter parts # 23-106-09 and # 23-105-09 are right- and left-hand brake assemblies that have dual mounting hole patterns, both 5-hole and 4-hole. These brakes are rated for use with 6000-lb axles.
  view full answer...
• Brake Assembly Recommendation for 6,000 lb AL KO Trailer Axles
  The Dexter Electric Brake Assembly # 23-106-09 is similar to the # 23-106 except it is designed to fit both 4 bolt AL KO style bolt patterns as well as the standard 5 bolt patterns seen on most other brands. Since you have Al KO axles you'd most likely need the # 23-106-09 for the passenger side and then the part # 23-105-09 for the driver side. You would want to check though. Look behind the trailer wheels at the brake mounting flange. If it's 4 bolts with the upper bolts being spaced...
  view full answer...
• Need Replacement Electric Brake Assembly For Old Flat Bed Trailer
  I walked out to our warehouse and pulled the Dexter 12 Inch Electric Brake Assembly # 23-105-09. It appears you do have a 12 inch brake assembly, and the measurements you provided match that of the Dexter Brake Assembly. The # 23-105-09 is the left side brake assembly, for the right side of your trailer, you will need Dexter 12 Inch Electric Brake Assembly # 23-106-09. This Dexter brake assembly will fit a 4-bolt brake mounting flange. Checkout the short video I produced for you showing...
  view full answer...
• 12" x 2" Trailer Brakes Assemblies Rated for 6,000 lbs With 4 Bolt Mounting Flange Pattern
  There are 12" x 2" trailer brakes available that are rated for 6,000 lbs and have a 4-bolt mounting flange pattern. The Dexter Electric Brake Assembly will work with 14-1/2", 15" or 16" wheels; for the left-hand side you need # 23-105-09 while the right-hand side is # 23-106-09. I have added links to video reviews of each brake assembly for you to take a look at.
  view full answer...
• Replacement 12 inch Brake Assemblies for Prowler Trailer With 4 Bolt Mounting Flange
  Definitely looks like you have the Hayes 4 bolt style of 12 inch brake assemblies. So for the right hand side you'd want the part # 23-106-09 or for the left hand side part # 23-105-09. We wouldn't have just magnets for your assemblies but by the overall condition of your assemblies just replacing them would be your best option.
  view full answer...
  
• 12 inch Diameter Trailer Brake Assembly Recommendation with 4 Bolt Mounting Pattern
  We have the Dexter Brake Assemblies part # 23-105-09 and # 23-106-09 which are 12 inch brake assemblies that have both a 4 and 5 bolt mounting flange.
  view full answer...
• What is the Diameter of the Axle Cutout in Dexter 6,000 lb Electric Brake Assemblies
  The center hole in the Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange, 12 inch, Left Hand, 6,000 lbs Axle # 23-105-09 measures 3-1/4 inches in diameter. This is the same on the right hand brake assembly, part # 23-106-09.
  view full answer...
• Recommended Electric Brakes for 1986 Royal Internation Sportman 32 with Hayes 12x2 Brakes
  Thanks for your picture it was a great help! Looks like your 1986 Royal International Sportman 32 had the older Hayes brakes. The correct replacement assemblies for this are the # 23-106-09 for the right hand assembly and # 23-105-09 for the left hand assembly. I have linked them to this page for your purchasing convenience.
  view full answer...
  
• Replacement 12 inch by 2 inch Brake Assemblies for 6k Axle that Use 4 Bolt Mounting Pattern
  We have the brake assemblies you are looking for. The only 6k rated 12 by 2 inch assemblies we offer that have the same unique 4 bolt mounting patter are the # 23-106-09 for the right hand side and part # 23-105-09 for the left hand side.
  view full answer...
• Brake Assembly Recommendation for Stock Trailer with 4,500 lb Axle and 5 Bolt Brake Flange
  Going with heavier duty brake assemblies than needed like the part # 23-105-09 and # 23-106-09 is not going to affect the weight rating of your vehicle's axle. You would end up with just brake assemblies that are rated a bit higher than needed but will still operate just fine on your 4,500 lb axles. In general the overall weight capacity of an axle or trailer is the lowest rated component in the setup. Increasing the brake capacity would not give you a higher axle capacity.
  view full answer...
• How to Determine if 6k Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange Will Fit Flange
  You'll need to do some quick measuring of your backing plate/brake flange to see if you can use the 6,000 lb Dexter Electric Brake Assembly for 4 Bolt or 5 Bolt Flange - 12" - Left Hand # 23-105-09. I have added photos below that I hope will help. One is of a standard 5-bolt brake flange where the bolts are 2-1/8" apart except for the bottom which are 3" apart. The other photo is of is the brake assembly which shows the dimensions of the AL-KO/Hayes 4-bolt flange, where the holes are 3-1/8",...
  view full answer...
  
• Trailer Brake Assembly Availability Measures 12 inches in Diameter with 4 Bolt Mounting Pattern
  We have the brake assemblies you are looking for. The only 6k rated 12 by 2 inch assemblies we offer that have the same unique 4 bolt mounting patter are the # 23-106-09 for the right hand side and part # 23-105-09 for the left hand side. This is for the non-standard Al-KO 4 bolt mounting flange that has a wider spacing for the top bolts than the bottom bolts.
  view full answer...

Do you have a question about this Accessories and Part?