Replacement Spacer Block for Trailer Hitches - 3" Long x 1-1/2" Wide x 3/8" Thick

Ask the Experts about this Draw-Tite Accessories and Parts

Hole Diameter of Dra...

Replacement L-Bracke...

Dimensions Of Draw-T...

Recommendation for a...

Trailer Hitch Recomm...

Trailer Hitch for a ...

Trailer Hitch for a ...

Trailer Hitch Recomm...

• Hole Diameter of Draw-Tite Spacer Block for Trailer Hitches
  The Replacement Spacer Block for Trailer Hitches - 3" Long x 1-1/2" Wide x 3/8" Thick # 01077-011 has a hole diameter of 0.531 inches. You will have no problem with the 3/8 inch bolt.
  view full answer...
  
• Replacement Spacer Block for Draw-Tite Hitch On a 2014 Honda Odyssey
  The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75270 which is a fit for a 2014 Honda Odyssey uses a square hole spacer which although we do not have the exact same one available as a replacement, we do offer the Replacement Spacer Block part # 01077-011 which should work.
  view full answer...
• Replacement L-Bracket for Trailer Hitch on a 1997 Nissan Pickup
  To replace the L-Brackets that come with the Draw-Tite Max-Frame Trailer Hitch Receiver # 75186 (for your 1997 Nissan Pickup) you can simply use part # RHK and then input the info about your trailer hitch to get the replacement hardware.
  view full answer...
  
• Dimensions Of Draw-Tite Trailer Hitch On 1978 GMC Pickup For Clearance
  I called my contact at Draw-Tite and asked about the dimensions you mentioned. They do not offer drawings of the items but did give me some dimensions that will help you determine if it will work for you. Spacer blocks, part # 01077-011 are required when installing the # 75034 hitch because of the rivets on the frame of your truck. You will need six of the blocks to complete the installation. The measurement from the bottom of the truck frame to the top of the receiver is 5-5/8 inches....
  view full answer...
  
• Trailer Hitch for a 1987 Chevy V10 Pickup Step Side Short Bed with Sport Bumper
  Your 1987 Chevy C/K pickup, V10, is the 1/2 ton 4x4 model. The standard suspension on it was not the heavy duty suspension. The rear gross axle capacity would have to be rated at 6,000 pounds for the HD suspension which was an option for the V20. The spacer blocks are # 01077-011 and they are sold individually. I am not sure what the Sport bumper looks like so I had to look it up. It is not a standard/step bumper so if that is truly the case then hitch # 75034 would not fit properly....
  view full answer...
• Trailer Hitch for a 1971 Chevy C10 Pickup Truck
  For your 1971 Chevy C10 pickup you can use Draw-Tite hitch # 75034. On short bed models you will also need 6 of spacer block # 01077-011 to complete the installation. The hitch does not fit models that have heavy duty suspension but I do not believe that the 1971 C10 had the heavy duty suspension. There is no information on the gas tanks being an issue for this installation. If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one...
  view full answer...
• Hitch Recommendation for a 1985 Chevy C10 with 6 foot Bed
  Yes, check out the Draw Tite hitch part # 75034. This has been confirmed to fit your 1985 C10 with a 6 foot bed and step side. Since you have a 6 foot bed you will also need the spacer block part # 01077-011. For trailer wiring you would want part # 18252. For ball mounts I recommend the etrailer Ball Mount Kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag.
  view full answer...
• Recommendation for a Class III or IV Trailer Hitch to fit a 1986 Chevrolet K-20 Pickup
  For you 1986 Chevrolet K20 pickup truck, I recommend the Draw-Tite Max-Frame Class III Trailer Hitch, # 75034. The Draw-Tite hitch will fit both 6 and 8 foot beds with the standard or step bumper. The hitch is a Class III hitch with a 2 inch receiver opening. The hitch has a Gross Towing Weight of 5,000 lbs and a Tongue Weight rating of 500 lbs. If you are installing this hitch on the 6 foot bed you will need to also order 6 of # 01077-011 3/8 inch spacer blocks. If you have the 8 foot...
  view full answer...
  
• Replacement Spacer Block For Trailer Hitch Receiver
  You'll need a new spacer block if you lost one inside your frame somehow, as a magnet scope is the best bet. So what you'll need to do is match up the spacer block size from your hitch with the closest available size: - Trailer Hitch Spacer Block - 3" Long x 1" Wide x 1/4" Thick # RP3022 - Replacement Spacer Block for Trailer Hitches - 3" Long x 1-1/2" Wide x 3/8" Thick # 01077-011 - Replacement Spacer Block for Trailer Hitches - 2" Long x 1" Wide x 7/16" Thick # 1080-012
  view full answer...
• Recommendation for a Trailer Hitch to Fit a 1986 GMC 1500 Truck
  For the 1986 GMC 1500 1/2 ton pickup, we carry a couple of different hitches depending on the bed length and bumper style that of your truck. If you have the 6 foot bed with the standard or step bumper you will need the Draw-Tite Class III Max Frame Hitch # 75034. This hitch has a 5,000 lbs towing capacity with 500 lbs tongue weight capacity. When installing this Draw-Tite hitch, along with drilling the mounting holes, you will need to use 6 of Spacer Blocks for 75034 Trailer Hitch #...
  view full answer...
• What Exhaust Modification is Needed to Install Trailer Hitch # 87408 on a 2011 Lincoln Town Car
  By looking over the instructions for the Draw-Tite Trailer Hitch, # 41116, since the bracket already has to be rotated 180 degrees, also moving it to the outboard side of the frame rail may make it so that it will no longer be able to reach the exhaust that hangs from it. There may also be too much space between the hitch and frame with the hanger moved to the outboard side of the frame. I have included a link to the installation instructions for you to view to give you a better idea of...
  view full answer...
• Trailer Hitch Recommendation for a 1987 GMC 1500 Pick Up Truck
  The Draw-Tite Class III Trailer Hitch, # 75034, will fit your 1987 GMC 1500 as long as it does not have a deep drop bumper. If your truck has an 8 ft bed and a deep drop bumper, then you will instead need the Draw-Tite Trailer Hitch, # 41504. I have attached a photo of a typical deep drop bumper if you are not familiar with them. If your truck has a 6 ft bed, then you will need additional hardware to complete the installation. You will need six 3/8 inch spacer blocks, # 01077-011, and...
  view full answer...
  
• Trailer Hitch for a 1979 Chevy C-10 with Trailering Special Package
  Actually several of your pictures did make it through! What you have there is the standard/step bumper on your 1979 Chevy C-10. Deep drop bumpers, also called cowboy bumpers, drop way down. If your truck has an 8 foot bed you can use Curt trailer hitch # C14082. If you have a 6 foot bed you would need hitch # 75034 and 6 of spacer block # 01077-011 to complete the installation. If you go with the Curt hitch then I also recommend etrailer ball mount kit # EBMK2416. It comes with a ball...
  view full answer...
  
• Trailer Hitch Recommendation for a 1987 Chevy C/K 1500 With a Deep Drop Bumper
  A deep drop bumper is a bumper that hangs further below the frame than a standard bumper. Check out the photo that I attached showing a deep drop bumper compared to a standard bumper and a step bumper. We have three frame mount trailer hitches that will work with a deep drop bumper on your 1987 Chevrolet C/K 1500. You could install the Curt Hitch, # C13099 or the Draw-Tite Hitch, # 41504. These are all Class III trailer hitches that have a towing capacity of 5,000 lbs and a tongue weight...
  view full answer...
  
• How to Adapt CE Smith Trailer Axle Kit CE33201GA-HUB for 55-1/2-Inch Spring Spacing
  We do not have axle kits with a 55-1/2-inch spring center spacing but you can still use an axle like # CE33201GA-HUB so long as it is rated properly for your application simply by having two steel spacers like # 01077-011 welded at the appropriate positions on the axle tube. You may just need to enlarge the holes to match the size of the nuts on the spring stacks before you have them welded on. It is not a good idea to drill new holes in the axle as this could reduce its capacity. This...
  view full answer...

Do you have a question about this Accessories and Part?