Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
Simplify the wiring process for your RV solar panels by creating a strong, simple connection anywhere on your rig. Durable, protective housing with quick-connects for solar cables. Pre-installed, 10" MC4 cables splice to your internal wiring.
Features:
Specs:
If your RV does not have a refrigerator vent or you need another entry option for your solar cables, the Go Power cable entry plate is a perfect solution. The plate makes it easier to connect your cables with pre-installed MC4 connectors and lets you choose a convenient entry point on your RV. Additionally, the covered housing helps protect your wiring while preventing leaks by covering and sealing the install area.
The MC4 connectors provide a quick way to attach the solar cables on the outside of your rig to your internal wiring. Inside the plate, the jam-nut is thread-locked to resist vibrations and protect the connections during travel. Additionally, the plate has channels on its underside that guide adhesive sealant during the mounting process to ensure a proper waterproof seal.
This cable entry plate comes pre-wired with 10" of MC4 cables for your internal RV connections. Typically, these will connect to your solar controller. Use 10 AWG to 6 AWG wire for additional internal wiring. The ideal location of the plate, as well as your solar panels and solar controller, is near the battery compartment. The total cable length should not exceed 25 feet. Using a drill, install the cable entry plate to your RV roof using 6 pan-head (#10 or #12, not included) screws.
Use a sealant that suits the material of your RV's exterior. If you have to attach the plate's cables to your internal wiring, you need compatible, heat shrinkable butt splices (10 AWG to 6 AWG wiring). Finally, as an additional safety measure, connect a 30-amp in-line fuse (not included) to the positive wire near the battery.
Alternate Instructions
California residents: click here
Average Customer Rating: 4.6 out of 5 stars (26 Customer Reviews)
Simplify the wiring process for your RV solar panels by creating a strong, simple connection anywhere on your rig. Durable, protective housing with quick-connects for solar cables. Pre-installed, 10" MC4 cables splice to your internal wiring.
I ordered one of these and liked it. So I ordered two more. But I guess the product design changed in the 4 weeks between orders because a different style arrived. The new style does not have a flange, just a thin edge, where you can put silicone to make a gasket. So you have to install it without the silicone and then apply silicone to the outside corner where it meets the surface and hope it doesn't leak. The new design is also rectangular not square. So don't go off the picture if you think space is tight.
it was the exact replacement that I was looking for
I use this to provide solar power to my house battery (LiFePo) it is sturdy and well made. Now I don't have to leave my pantry door open to charge my battery
Great product. Used it on the side of my trailer for a portable solar set up. Easy to install and wire.
I used this to get power from a solar panel into an electrical box. Once in the electrical box it connects to the charge controller and whatnot. Using this was super easy and very effective.
Just what I needed, fast shipping and a decent price
Good product for the job. If it could have a little more water proof appearance as in better quality plus it will be perfect. Maybe the wires could also be a little longer
GETS IT DONE
Really a nice way to run the wires down into the chassis.
Arrived on time and in perfect condition. Exactly what I had ordered. Excellent service and help ordering! Good job.
gland with cable connectors built in. keeps flatter on the roof, and a cleaner disconnect. added to four wheel camper roof, and they have junction box ready. drill hole and connect.
I used this connector for a wall pass-through on my home. This allows easy connection for outdoor solar panels to my indoor battery storage unit. This product works great.
Exactly what I was expecting. I will use this on my Scamp 13ft to create a quick connection from battery to solar panel.
I must again say that etrailer has great customer service. Chat, phone, and email have all been top notch customer service. Thanks etrailer for doing that....really appreciate it.
Items as described.
Just finished installation on a 2019 Newmar Ventana.
Secured to roof with 6 self tapping screws.
thank you, shipping was faster than what was first said it to be. But inside of box could have used some dunage (bubble rap) as there was nothing but my parts.
Great
Good website, nice selection of products. Great service.
Item as Described, Easy Transaction, Fast Shipping Would Buy Again
Just perfect, and well made.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Bruce
4/28/2023
Working as intended, no problems.