Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
Wheel stud fits Kodiak integral hub-and-rotor brake assemblies with 10" diameter rotor. Bolt has a thread size of 1/2"-20 UNF-2A.
Features:
 | ||||
| Thread Diameter (A) | Stud Length (B) | Spline Length (C) | Base Length (D) | Spline Diameter (E) |
| 1/2" | 1-11/16" | 0.68" | 1.38" | 0.54" |
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Kodiak replacement drive-in trailer hub wheel stud. This one is a 1/2 inch diameter by 1-11/16 in length. It's a quantity of one. This 1/2 inch stud is designed to replace a damaged wheel stud on your trailer hub. The raised spline portion right here of the stud is what will be driven or pressed into your trailer hub. This stud is what will go through the bolt hole on your trailer wheel, and when used with a wheel lug nut will hold your tire and wheel to your axle. These are stamped as a grade eight bolt.
The thread size diameter is 1/2 inch, 20 threads per inch. It does use a standard 1/2 inch by 20 lug nut size. I did happen to pull one of those lug nuts, just to show you. Basically, once this is on your trailer hub, you just use this. Once you put your wheel on, use your lug nut to tighten down and torque it to the correct specs to hold your tire and wheel assembly to your trailer. The overall length, which will be measured from the bottom of the head to the end of the bolt; if we put a ruler on that, it's going to be about 1-11/16 inch.
The threaded length, just the threaded portion, is about 1-1/8 inches. Then the spline diameter, which is this portion here, is 0.54 inches. That should do it for the review on the Kodiak replacement drive-in trailer hub wheel stub, 1/2 inch diameter by 1-11/16 in length, for a quantity of one.
Average Customer Rating: 4.8 out of 5 stars (45 Customer Reviews)
Wheel stud fits Kodiak integral hub-and-rotor brake assemblies with 10" diameter rotor. Bolt has a thread size of 1/2"-20 UNF-2A.Replaced some rusted studs on a motorcycle trailer, so decided to do all five. They appear to be an almost perfect fit. Took some effort to pull them into the splines, they're not going anywhere. I put a dab of blue locktite just in case.
The reason I said almost perfect was they might be 1/16" shorter than the original. I never thought it would be an issue but they just make it flush to the outside of the lug nuts. I'd rather err on the side of too long than just short. Otherwise I'd think they're perfect.
BYW: I wasted $[XX] on a tool to seat the studs from Amazon. It's a cone shaped device with bearings so it turns and holds the lug nuts. The problem is it added enough thickness that I couldn't start the nuts. I ended up just using a lug nut with the flat side on the hub.
Think they will work ok.
I ruined the wheel, lugs and lug nuts on my utility trailer by letting the lug nuts get loose. Information on the eTrailer website made it easy to identify the replacement parts I needed. The parts came three days after I placed my order even though I did not specify expedited shipping. Assembly was easy, especially after watching an instructional video on the eTrailer.com website. I am very pleased with the entire transaction.
Perfect replacement for Ezlube 3500lb axles, after it forgot to tightened my lug nut and ruined the old wheel studs. Pound in to set them, the used a washer and backwards lug nut to pull the stud all the way in. Took 5 minutes to do the one wheel!
The question if the K12WB169 will work with the AKIHUB-440-2-1K trailer hub assembly could not be answered, when I inquired. The answer is yes! The 2" studs that came with the hub was about 1/4" to long for my trailer setup. The K12WB169 pressed in perfectly and the right length. With all the confusing research that I have done, I made the right choice.
I am in the process of upgrading my trailer for off road uses.
Not much to say. It's a lug stud that was hard to find, specific to a boat trailer. Service was great. Delivery was timely, and shipping was very fair, in fact it was significantly cheaper than the only other site in which I found this item.
Found exactly what I needed. Was concerned about ordering parts online due to not having trailer model number etc. but etrailers descriptions made it possible for me to exactly match what I needed!
1/2"x20 1 7/10" trailer wheel press in studs are hard to find, but thanks etrailer, I am very satisfied, Dexter.
What can you say about a lug stud? Kodiak OEM exactly fits my Kodiak hub. Fantastic customer service and speed of delivery.
THE PARTS I WAS LOOKING FOR WAS HARD TO FIND LOCAL AND E TRAILER HAD WHAT I WAS LOOKING FOR AT A GOOD PRICE. THE PRODUCT INFORMATION WAS VERY HELPFUL ALSO
The data sheet on the website matched exactly what I received. Dimension are critical to get the right studs for the trailer. My trailer is a twin axle coastline trailer made in Seadrift, TX
fast ship, perfect fit
The stud is the exact match of the one we were looking for. We were having a difficult time finding an exact match. Really helpful having the exact dimensions listed since there are so many studs to choose from.
Perfect fit for my trailer hub.
.
Product was as described. Haven't had an opportunity to see if they are the ones I need. Delivery time was very quick.
Not bad, just wish it would have fit the hub tighter!
The studs are good quality items and were delivered promptly and packed well.
Excellent quality
Studs work great.
Great service, would purchase from this Co. Again.
Seems to be a quality product, made to specs, delivered quickly.
I could not find these anywhere else
Great quality , exactly as described.
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
John L.
2/10/2018
Theyre swell. A bolt and a lug.