Replaces your power landing gear follow leg and snap pin. Enjoy the power setup while you are out camping and know that your RV or fifth-wheel will be steady and secure.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today I'm going to take a look at the replacement fifth-wheel RV landing gear follow leg with the snap pin for Lippert Components RVs. This will replace your follow leg and snap pin on the Lippert Components power landing gear. It's designed to fit the standard power landing gear, supports your fifth-wheel to prevent unwanted movement. It's designed to connect right here to the lead jack and the landing gear set, with a connecting rod or a cross shaft, which we do sell separately. It does include the two zerk grease fittings, one right here, one right here for lubrication of the jack. This is constructed of a heavy-duty steel, has a nice black powder coat finish to it.
Part is made in the U.S.A.A few specs on this, the weight capacity. If it's a manual crank is going to be 4,000 pounds per leg. If it's a dual motor, it will be 4,000 pounds per leg. And if it's a single motor it'd be 2,500 pounds per leg. Overall height, which will be measured from the top to the very bottom of the inner tube right there, if we put a tape measure on that right here ...
Very top here you're going to see is right at 32 inches overall height. Total width on this going to be right at 2 1/2 inches wide. Now the outer tube, which is the black portion from here to the very bottom on the black tube, that's going to be right at 29 1/2 inches tall.And then the bracket stops or the weld stops right here on each side. This is where your jack will attach to the mounting brackets on your trailer. Outside the outside, which will be from here to down here.
You're going to be looking right at 17 1/2 inches, and inside the inside, 15 1/2 inches. So, each weld stop is about an inch wide. But that should do it for the review on the replaces fifth-wheel wheel RV landing gear follow Leg with the snap pin for the Lippert Components RVs.
Average Customer Rating: 4.9 out of 5 stars (92 Customer Reviews)
Replaces your power landing gear follow leg and snap pin. Enjoy the power setup while you are out camping and know that your RV or fifth-wheel will be steady and secure.Landing gear works great just like original equipment. It took about 7 hrs. to remove and install due to very tight working quarters and I am pretty handy with all the proper tools needed and some, so be patient, not as easy as the you tube video I saw.
Richard - 03/15/2019The packaging was insufficient for the product, but the sales representative was helpful, the package was delivered timely and the product seems to work well so far.
Donna was a great help getting our order for a front landing leg. Called on Monday am and order was received at our destination by Wednesday, today with a short time had the leg replaced. Great customer service!!!!!
LC179014 - 09/13/2019great product with easy install ,customer service and knowledge is fantastic,you have a customer for life
Product is better than new, love the added grease fittings(zerks), this will provide a way to lubricate them for a much longer lasting.
I received the product sooner than expected from ETRAILER, however our local UPS could not deliver for a few days due to stormy conditions.
I installed the jack this morning and was back in operation sooner than expected.
Great product, great service and super customer service representative (John) to work with.
Thank you
Anthony R - 09/09/2017I replaced both the left and right side landing gear jacks and they fit perfectly and were easy to install. They also have the zerk fittings so they can be greased.
GuyN - 01/24/2018Great people! Love working with them!
Several teeth were broken off or worn down, on my following leg landing gear, on our 2005 Keystone Challeger 5th wheel camper. our local dealer wanted $500+ to remove it, and reinstall a new one. After some on-line searching, I found this etrailer.com website. After looking at reviews, I followed their recommendation, and ordered the LC179014 leg and gear. I put in the order late afternoon on Wednesday, and it was on my doorstep Friday afternoon!!! I took the old leg out. The new leg would not "seat" correctly, and I was concerned I had made a mistake purchasing it. After doing some investigation, I found a bead of weld - on my camper - was preventing the leg from locking in place. I ground it off with my angle grinder, and the new leg fit PERFECTLY!! This new replacement weighs about 4 pounds more and is heavier constructed than the original. Plus the fact, there are grease zerks on the new, so it can be properly lubricated - unlike the factory one! In summary, THANK YOU e-trailer.com for a fantastic part!! You saved me about $400. I will be using your website again!! Ron
Fast delivery, all parts necessary to connect crossbar, product came ahead of estimated delivery!
Levi V - 06/24/2021Just the part I needed arrived in a reasonable time
When I have a trailer need I go straight to etrailer.com. Great products, great support, great service. You've earned my loyalty.
If anybody need to know how to install a landing gear leg on a Grand Junction, feel free to contact me.
The parts came in good, the customer service was good. I wish they would have let me know that they were waiting on the small bracket but when I asked about it they were very up front about it. SO I am very pleased with everything.
This is a very good internet company to deal with.
We ordered the landing gear follow leg for our fifth wheel trailer free shipping was a plus. The leg arrived a 2 days earlier than expected another plus. The leg fit perfectly after we discovered that the original leg had been bent and twisted slightly from the previous owners. We were able to make a few adjustments and we installed the new leg with no other problems. All in all the job took a little longer because of the damage we had to fix but went smoothly after that. Will use e-trailer again. Thank you Michelle for your assistance, God bless
I am the original owner of a 2010 Montana Mountaineer 5th wheel. I replaced both the lead and follow landing gear. I studied the different landing gear available, and chose to try the cheaper items. These less expensive ones LC179014 and LC179013 were exactly the same as the old ones. Installation went smoothly, and they fit perfectly.
This was a great purchase to replace the existing front end camper jacks. Replacement was very simple and operation is very smooth.
The product itself has fixed my problem. I am most happy with the service provided by Pat. With a broken landing gear, I could not get my 5er off the truck easily. I chose to leave it on the truck until I got the replacement. My issue was living in an HOA and it's rules. Pat made sure it got to me as quick as possible. Ordered it on Tuesday, got it on Friday. I've used ETrailer a few times and have always been very happy with pricing and service.
First i would give 10 stars if i could, my part was lost in shipping by ups, i called Pat in customer service and Boy what service, she shipped out another part that day, Thursday and i received it on Friday, the next day. Everything fit perfectly, to those of you that need to order this part check all the measurements and if your are the same it will fit with out alterations . I just can't say enough about this company and this is the very first time i have used them, it won't be the last and i have told all my RV friends that this is a company that cares.
Thank you Pat and all of the employees that were involved in making this experience with your company go so well.
Larry S - 09/18/2019Fit perfect. Exactly as described and fast delivery . A replacement follow leg for my 5th wheel...Great company to get products from.
Stanley - 09/14/2019Product shipped fast and was relatively easy to install. With some difficulty from the fifth wheel bolts (that were previously installed backwards), the legs fit perfectly. Both work in harmony and I cant wait to use them full time this coming summer. The grease zerks will also be a nice compliment, as the prior ones did not have them, which is why I'm suspecting they faltered in the first place. Will be doing business again with etrailer.com!!!
Best investment for the camper we have gotten. It cools immediately and runs perfectly. Has different settings that allow the fan to run constantly which is great. I am a light sleeper and can't have the fan turn off and on. It's exactly what we needed & we haven't had any issues. No leaks, no down time.
Received my 5th wheel landing gear on time & installed on trailer.....functioned landing gear after installation & worked perfectly...saved a ton of money on what the cost would be from RV place...took about 1 hr. & fit like a glove...anyone can do it....thanks for help...great info. on web site...have ordered from them several times & will order from them again for my trailer needs
Very easy to install.
Ashley R - 12/07/2021After just recently having problems out of my rig and with lots of research and YouTube videos I was made aware of etrailer. They have an amazing and informative website but they also have the best customer help I’ve ever seen when it comes to calling. I was accidentally sent the wrong landing gear leg on the first try but I called immediately after realizing it was wrong and they went above to make sure it got sent back and didn’t hang the phone up until we were 100% certain I was being sent the right one this time. I would recommend them every chance I got!
Purchased the Following leg to replace a failed unit. Installation was easy on this side as three bolts are removed to make the exchange. The new unit has an additional grease zert for lubricating the top gearing section, which has a removable cover for inspection of the gearing. This unit would receive an excellent score if the leg was manufactured with access to the screw that makes the leg travel. Lubrication to this screw thread would greatly extend the life of the product.
The Landing Gears have worked flawlessly for the last year. I have lubricated them once using Valvoline Multipurpose Grease #615.
Ron H - 05/05/2018
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.