Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
(503 reviews)
Price: $6.41
In Stock
Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
Item # A47PB
Retail:$9.50
Our Price: $6.41
You Save: 33%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (503)
- Q & A (0)
- Photos
Optronics Accessories and Parts - A47PB
- Trailer Lights
- Wiring
- Plugs and Pigtails
- Three Wire
- Optronics
- Right Angle Pigtail
- 10 Inch Long
This 3-wire pigtail has a male plug on one end that pairs with the female connection on the back of your Optronics light. Right-angle plug allows wires to run down from light instead of straight out the back. Designed for stop/tail/turn lights.
Features:
- Pigtail with 3-prong plug allows you to wire your Optronics light to your trailer
- Designed specifically for use with Optronics stop/tail/turn lights, parking/turn lights, and warning lights
- Right-angle design of plug allows wiring to run down from the light rather than straight out of the back
- Male-pin, 3-prong PL-3 molded plastic plug connects to back of trailer light
- 3-Wire pigtail
- White wire for ground
- Black wire for tail light
- Red wire for turn signal
- #10 Ring terminal on ground wire
- Wire length: 10"
Pigtail is a direct replacement for:
- Uni Bond PT9530
- Truck Lite 94993
- Grote 66843-3
- Peterson 421-491
A47PB Optronics PL-3 Right Angle 3-Wire Pigtail for Trailer Stop, Turn, and Tail Lights
Alternate part number: A-47PB
California residents: click here
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead - A47PB
Average Customer Rating: 4.8 out of 5 stars (503 Customer Reviews)
This 3-wire pigtail has a male plug on one end that pairs with the female connection on the back of your Optronics light. Right-angle plug allows wires to run down from light instead of straight out the back. Designed for stop/tail/turn lights.by: Mike08/23/2020
Definitely made wiring the lights an easier task as I completely forgot about the wiring harness until the lights showed up and had to go back and order them. Added new brake, turn lights, as well as back up lights to both sides on the boat.
by: North Georgia Fence Co.11/03/2023
I was easily able to locate the trailer lights I required on this excellent website. Delivery was fast and the product was excellent. Thank you!
by: Bruce F. 02/08/2019
The space behind the Optronics tail lights I chose for my concept Lotus T66 Europa is extremely tight. Normal connectors that bring wires straight off the back wouldn’t fit. This connector brings the wires out at a 90° angle, keeping them close to the housing. It made installation a simple matter.
Bruce F.
2/8/2020
Of all the lights in my BritishFrench car, these are the only ones that have given me ZERO issues. They are fully enclosed, fully sealed with rock solid connections. Made for trucks but look awesome on a 40” high concept race car.
by: Keith G.07/08/2017
Ordered the pigtails, lights and grommets to add additional lights to my cargo trailer I pull behind my motorcycle. These lights were easy to install, the wiring worked great with my already wired lights. The lights work great and are easily seen. Great product and would definitely buy again. This pigtail made wiring the lights quick and easy.
by: Farmdog06/21/2023
All my trailer parts for a new build keep coming in from etrailer , my go to online store. Everything needed for building and maintaining trailer etrailer has. I have been dealing with etrailer for several years now and have never been disappointed.
by: Edward 07/23/2023
Pigtails were of good quality but note that using them may require a hole of about 1 and 1/8
by: John S.07/18/2016
Everything worked very well together. Sorry I don't have picture of lights in action attempted to upload a short video but site would not accept it as a valid file type. Just let me say guys riding behind me don't wanna be to close when it is dark out cause all they see is red!
Randall
7/30/2017
Wonderfully
by: Wyatt07/23/2022
Just the plug I needed! Using it for my boat trailer and did not want to have to order through the dealer. Great service and speed.
by: Doug 04/28/2023
This fit onto the back of a Ranger Trail taillight assembly.
by: S. Mono08/14/2017
Good fit and materials, although the splice into an extension to plug directly into a standard 4 pole flat trailer hitch connector, was trial and error to get the correct functions of the light.
by: Arthur 09/29/2023
i have no put them on but i feel that they will be a great fit
by: Ray 09/21/2023
Really locked good , fit perfectly in my 2013 Cedarcreek Silverback LB35
by: David05/03/2020
I have purchased scores of products online over the years, but this experience was by-far the best. Your website is well organized, well informed, and easy to navigate. The purchasing process went very smoothly, and the products that I purchased were competitively priced. The shipping and delivery was faster than estimated (and frankly, faster than I expected). The shipment arrived well packed, undamaged, and the contents were exactly as advertised. Thank you etrailer.com for a great experience...I'll be back to purchase again!
by: Darryl 01/21/2023
Fit good, great price, fast shipping - replacing one that was torn up when I had a trailer tier blow out - I really appreciated the fast shipping on top of a website that easily found the part
by: Mike 08/29/2023
Fairly quick. Fairly priced.
by: Andrew 07/27/2023
Good product and service
by: Bill 06/20/2023
Love these, positive fit
by: leo08/10/2022
packaging of taillights where loose causing them to get scuffed and scratched during shipping, quality and visibility of lights are excellent and pigtails really good, if lights would be individually packaged and taken better care of i would give 5 stars
by: Mike f10/23/2016
Purchased the three way sealed tail light, 3 wire pig tail, and PVC grommet for my boat trailer. Everything worked as explained in store video(these videos are excellent idea and reason I purchased from you VS other on line stores). Purchased 2 of each product so i would have spare in case tail light on other side of boat trailer failed. great quality, and price. Received in 3 days.
Mike F.
10/23/2017
Tail light continues to function - no issues after 12 months.
by: Richard05/22/2023
Exactly as advertised. They look good. Haven’t tried yet!
by: Linda 06/11/2023
Perfect ordering & delivery was awesome, quick & easy:)
by: Craig09/30/2016
What do y'all want a follow up to? If i had a nickel for every item I've ordered off of ETrailer, I wouldn't have to work for a few months... I keep coming back because the prices are fair, shipping is free and fast, and ETrailer has everything I need.
I do wish you sold trailer kits though. Being a welder, I have built a few trailers in my free time and sold them for a small side business. Why isn't there an axle, fender, brakes, springs (shackles and all hardware) tires and wheels kit? It would be nice to not have to go and click and add to cart all the multitude of items I need to build a trailer individually. Just saying...
by: Hyler10/08/2022
Well made, old look and fits. LED an improvement over old lights. Perfect for our old truck.
by: Gene W02/07/2020
I love the LED tail lights that I purchased for our travel trailer. Exceptionally bright and they give me a lot more confidence driving down the road both in daylight hours and after dark. The trailer manufactures should be installing these tail lights from the get go. They were easy to hookup and install and the full size foam rubber gasket makes a great seal. The picture you see with my review isn't of the tail lights.
by: Randy09/29/2016
Etrailer MCL48ab light from Optronics is AWESOME. Comes in AMBER and RED. 16 BRIGHT LED's along with the Miro Flex Technology. (each LED is surrounded in a highly reflective metallic prism) Like todays bright car headlights. 4 bulbs facing forward, 6 shining to the sides, and 6 shining upwards and down. Purchased amber for the trailer to see how bright this was, no getting ready to order 12 for the rear of the trailer. Was going to use Double Bullseye units, now going to use the MCL48AB. Note: there is a different part number if you reference it on the Optronics website. When you come to ETRAILER.COM to purchase it, its the same unit. Great purchase for the money, COOL look to it, solid construction, BRIGHT, great technology. The shipment from Etrailer came quickly and packed properly.
25
503
Show More Reviews
See what our Experts say about this Optronics Accessories and Parts
- Functions of the Three Wires on Trailer Taillight Harness A47PBOur three wire lights like what the harness part # A47PB is designed to fit have the white wire as ground, the black wire for tail light, and the red wire for stop/turn signal. That covers all of the standard trailer taillight functions.
view full answer... - How Do I Wire a 3 Wire Pigtail # A47PB to a Trailer that has 2 Tail Light WiresYou will wire the black and red wires from the 3 wire pig tail to the two wires from your trailer, the red wire will be wired to the turn signal circuit and the black wire will wire to the tail light circuit. The third (white) wire from the pig tail is the ground wire and will need to be attached to a good clean ground on your trailer.
view full answer... - What is the Wire Gauge Used for Right Angle 3-Wire Pigtail # A47PBThe wires for Right Angle 3-Wire Pigtail # A47PB are 18 gauge. I am not sure which oval lights you are referring to. Any that would take this pigtail do not have wires. If you can tell me a specific part number I can check the wire gauges for it as well.
view full answer... - What is the Wire Gauge for Right Angle 3-Wire Pigtail # A47PBI went out to the warehouse to check the wire gauge on Right Angle 3-Wire Pigtail # A47PB. Each of the 3 wires is 18 gauge. At 10 inches in length 18 gauge automotive-grade wire can handle a maximum of approximately 15 amps which is much more than any light that it goes with pigtail A47PB.
view full answer... - Does Right Angle 3-Wire Pigtail 3-Prong PL-3 Plug # A47PB Fit PL-3 ConenctorYes, the Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug # A47PB is designed for the PL-3 female connector as this is the male side.
view full answer... - Replacement 3-Wire Pigtail For Tail Light On 2011 TrailStar Boat TrailerWe offer a couple different 3-way pigtails that are typically used for a sealed trailer tail light that may work for you. The first is a right angle 3-wire plug, part # A47PB. It has three wires, a red, black, and white. The red is a turn signal, the black is the tail signal and the white has a ring terminal on it and is designed to be the ground that needs to be attached to a clean metal surface. The 3-way plug is designed to plug into the back of a sealed light. For a straight 3-wire...
view full answer... - Repelling Moisture and Corrosion Using Right Angle 3-Wire Pigtail # A47PB For Trailer Tail LightsOnce the right angle pig tail harness, # A47PB, is plugged in it will seal up nicely but for additional protection from moisture and corrosion apply some dielectric grease, # 11755, to the pins before plugging the harness into the light. Dielectric grease is hydrophobic and will repel moisture and resist corrosion.
view full answer... - What Pigtails Are Needed For Optronics Submersible LED Trailer Tail Light With Backup LightsYou are correct that you will need two pigtails for this light. I spoke with my contact at Optronics about the Trailer tail Light, part STL211RB. One plug is to be used with a 3-wire pigtail like part # A47PB for the right angle plug or the straight 3-wire pigtail part # A45PB. The other plug will use a 2-wire pigtail like part # A45CB, which will be used for the back-up lights only.
view full answer... - How Does Optronics STL101RCFB GloLight Ground to Trailer FrameThe # STL101RCFB Optronics GloLight would ground to the trailer frame via the 3 prong pigtail that's sold separately as # A47PB for a right angle plug or # A45PB for a straight plug. The white wire on the pigtail is the ground connection. The red wire carries the turn signal/brake lamp circuit and the black wire carries the running lamp circuit. I've linked to some product videos that you might find helpful.
view full answer... - Diameter of Mounting Holes for GloLight LED Trailer Tail LightThe GloLight LED Trailer Tail Light # STL111RFB has mounting holes which are 3/4" in diameter. You would also need a 3-wire pigtail # A45PB or # A47PB to connect the light to your trailer or vehicle. I've added links to video reviews of these products for you to take a look at.
view full answer... - Mounting of Optronics 4 Inch Round Tail LightThe Optronics Tail Light # STL43RBX does not need a bracket for mounting. It has a built in flange and includes a rubber grommet. The light can be connected using a 3-wire pigtail, # A45PB, or # A47PB for a right angle.
view full answer... - Replacement Pigtails for Optronics LED Trailer Tail Light Yes, there are a couple of replacement pigtails for the Optronics LED Trailer Tail Light item # STL42RB. One is a right angle plug the other is a standard. I have listed them both below. Right Angle 3-Wire Pigtail for Optronics Trailer Lights item # A47PB 3-Wire Pigtail for Optronics Trailer Lights item # A45PB
view full answer... - Replacement Optronics 5-1/2 Inch Diameter Round LED Trailer Light I think the part number you have on your trailer is part # STL42RB. The other numbers may be a serial number or another number for a mold or something else. The best way to see if our light is the exact replacement is to check the specs and the mounting of the # STL42RB. The light has 10 LEDs and uses a 3-prong plug like part # A47PB for the right angle plug or part # A45PB for the straight plug. The dimensions of this light are 5-1/2 inch diameter and 1-15/16 inches deep. The mounting...
view full answer... - 3-Prong Pigtail Wiring Needed for 10 Diode Optronics LED Trailer Tail LightThere are 2 different pigtails available for the Optronics LED Trailer Tail Light # STL78REZB and the correct one really just depends on what kind of space you have where you're installing the light: - Straight Plug # A45PB - Right Angle Plug # A47PB Attached are some installation videos for you to check out!
view full answer... - Which Type of Pigtail Lead to Use with Optronics Round LED Trailer Stop/Turn/Tail Light # STL42RBThe Round LED Trailer Stop/Turn/Tail Light # STL42RB from Optronics uses an industry-standard 3-prong plug. The two plugs you referenced, the Straight 3-Wire Pigtail # A45PB and the Right Angle 3-Wire Pigtail # A47PB, both will fit this light assembly. You choice will just be a matter of preference depending on the amount of clearance you have behind the light's mounting points. If space is tight then the right angle plug might be a better option. I suggest you apply dielectric grease,...
view full answer... - How to Wire the Sealed 4 Inch Round Trailer Stop Turn and Tail LightThe sealed, 4 inch round trailer stop, turn and tail light, # ST48RB, is designed to be used with the straight or right angle 3-Wire Pigtail, # A45PB or # A47PB. The white wire with the ring terminal on the end of it is ground, the red wire is for the brake and turn signal functions, and the black wire is for the tail light function.
view full answer... - Availability of the Trailer Taillight STL72RB with 90 Degree PigtailIt sounds like you have the # STL72RB, but then also have the 90 degree harness # A47PB instead of the straight harness part # A45PB.
view full answer... - Solution for Installing Optronics LED Trailer Tail Light on Trailer With Round 3-Prong Light PlugThe Optronics LED Trailer Tail Light # STL43RB is only available with this plug style. We do not carry the GROTE brand or have any lights like this that match the round plug. However, a simple solution would be to cut off your existing plug and use the # A47PB or # A45PB.
view full answer... - How to Determine if Trailer Light ST70RB Will Work as Replacement.We would have no way of knowing a specific trailer light on any trailer, including your 1993 Heritage, so the best we can offer is to tell you how to determine you can use the Optronics Trailer Tail Light # ST70RB. Just measure your light, and if you get the same dimensions - 6-1/2" long x 2-1/4" tall x 2-3/8" thick - then you can use this light. It will also require 3-Wire Pigtail # A45PB or # A47PB.
view full answer... - Will the LED Tail lights and the 3 Wire Pigtail Fit on a 6 X 12 Foot Haulmark Enclosed TrailerThe Sealed, 6-1/2 inch Oval LED Trailer Stop, Turn and Tail Light, will fit in the factory grommet if the original light measures 6-1/2 inches overall width and 2-1/4 inches overall height. This is the standard size of most of the lights installed on enclosed trailers. I have seen some lights that are 7 inches overall width and if your original is this size then the 6-1/2 inch light will not fit in the original grommet. At this time we do not carry a 7 inch oval taillight The 3 wire pigtail,...
view full answer... - How Does Backup Light of Fusion LED Trailer Tail Light WorkIn order to utilize the backup light function of the Fusion LED Trailer Tail Light # STL211RB you will need to plug in a 2-Wire Pigtail, either part # A45CB or # A49PB for a right angle pigtail. You can see from the accompanying photo of the rear of this light that it has connections for both a 2-wire and 3-wire plug. This would need to be used along with the 3-Wire Pigtail # A45PB or # A47PB (right angle) which gives the light its tail light functions. I looked up your order from the...
view full answer...
- Plugs Needed for the Fusion LED Trailer Tail Light # STL211RCBAt first I thought that this light had 2 places for the 3 terminal plugs but if you check out the attached picture of the Fusion LED Trailer Tail Light # STL211RCB you can see that one plug has 3 prongs (for tail light functions) and one plug has 2 prongs (for reverse light function). If you are just needing standard plugs then you would use part # A45CB for the 2 prongs and part # A45PB for the 3 prongs. These are also available at right angles with parts # A49PB and # A47PB respectively.
view full answer...
- Availability of 3-Pin Pigtail Wiring Connectors for # 98174LED Cargo Carrier Light KitAre you needing the pigtail that will plug into the lamps? If so, a right angle pigtail is available as part # A47PB. A straight plug is also available as part # A45PB. If you're looking for a female socket that will accept the existing plugs to make an extension, Optronics doesn't offer such a part. If you need do some cutting and splicing, I'd recommend soldering your connections and protecting the connections with heat shrink tubing like part # DW05451.
view full answer... - Troubleshooting LED Clearance Lights on Boat TrailerAny trailer light, whether standard incandescent or high-efficiency LED, should light up when it is connected directly to the terminals of a charged 12V battery. Direct connection avoids all other potential causes for problems, such as broken wiring, a weak ground or corrosion, and tells you whether the light functions independent of any other concerns with the trailer's wiring. But since your light works when installed on the other side of the trailer, but not when directly connected to...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Installed by:
Jeff D
Installed by:
Andrew S
Updated by:
Laura H
Updated by:
Amy B
Updated by:
Brian T
Updated by:
Noah M
Video Edited:
Chad S
Video Edited:
Chris R
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Michael E.
8/24/2021
Work great! Super bright and recommend the items to others. Have almost replaced all the lights on the entire trailer with your products. Thanks again!