To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. Connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side interior trim panel in your rear cargo area. Once you've plugged in the T-connector, insert the included 10-amp fuse into the integrated fuse holder. Then install the 10-amp mini fuse and two 7.5-amp mini fuses in the rear fuse panel.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plug on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (331 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. Connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.Arrived as ordered and when promised. Simple instrictions with pictures.
Three words sum up the service: Quick, Simple, Painless!
Thanks!
Great company! Super fast delivery, friendly helpful service and a product that performs as promised.
I'd give it 5 stars if it wasn't for the fact that the kit comes with 2 fuses (4 are needed).
Bottom line, I'd buy it all over again!
Good prodcut. Directions could be a little better, and unfortunately there was no video for this product, but following the video for a similar product helped.
Worked great. Just plugged in the connector fuses and ran the wire and bingo all done. Grate e-sight to shop at.
3 day dilvery. Install same day hitch lined up nice and looks nice.
I am very happy with it.Instructions clear good price.
Jim
Instructions were simple and clear. Wiring harness connected quickly to all factory plugs and could not have been easier. If instructions are unclear for any reason, take 2 minutes and watch the how to video.
Curt T-Connector installed just as video showed on my 2011 Honda Odyssey. I am 110% satisfied with shopping/installation experience. I highly recommend to all you do-it-yourselfers...
Fit perfectly, installed easily.It took me a couple of hours to install (in the snow 200 ft from my toolbox - don't ask). Instructions were clear with nice pictures. I had looked at a YouTube video previously which made it even easier. The only hard part was finding a good grounding point. I used an existing hole after I ground off the undercoat. Worked perfectly.
John
This kit fits my 2011 Honda Odyssey perfectly- it plugs right in. So for those of you with the new odyssey, rest assured that this is the wiring harness you need.
Works like a charm. The installation instructions could be just a little more detailed. Be careful when removing the interior trim. It is very easy to break all them cheap plastic fasteners. That can become a head ache. Just take your time.
Recieved the product in good time and installed the wireing harness
in about 45 minutes from start to finish being carefull not to damage
any of the trim.
Very easy install. I was nervous about taking sections of the trim off, but they went right back in place, no problem. As another review said, it was a little difficult finding a grounding spot. I used the screw-in trim holder half way up the trim, on the driver's side, right next to the hatch back door. After sanding off the paint on that spot of the frame, I was able to ground the unit when I used that screw to put the trim back in place.
Works goodThis wiring was fairly easy to install. I used a combination of the instructions in the kit and instructions from the Honda factory tow package to see where all the clips were in the panels so I didn't break anything. The rear plastic panel is difficult to reinstall since you have to make sure you get the retaining clips in the right spots on both sides of the panel. You can probably run the wires though the rubber plug in the rear of the vehicle and under the bumper if you wanted them near the hitch. I left mine inside the vehicle for now. The wiring seems to work as it should.
This harness was extremely easy to install and fit nicely inside the trim panel and it didn't require any splicing as there was already a ground bolt right below the left tail-light. It also maintains a strong current so trailer lights are equally as bright as vehicle lights.
Highly recommended!
I installed my harness back in April. See my review on 4/26/11. Yesterday was the first time I had a chance to hook up the boat and go fishing. Much to my chagrin, the trailer lights didn’t work. With the help of my mechanic, it appeared that electricity was going from the car into the converter but not out. I called Etrailer and talked to Rose. She was very helpful. She arranged for me to return the wiring harness under their warranty. Rose explained that I will get a credit for the unit after they have a chance to look at it. Since I only live an hour away, I dropped off the unit at their Wentzville location. Rose also prepared a will-call order for me to pick up a replacement harness while I was there. Very smooth. When I arrived, I received first-rate help from Courtney with my return and will-call pick up. While I was there, I saw they were having a sale on bike racks—one too good to pass up. Courtney provided a lot of information to help me pick out a 4-bike Yakima bike rack. Then she diligently ensured I had all the proper pieces that come with the rack. Now, after having a pretty good day, imagine my dismay the next day when the new vehicle wiring harness did not work. OK, what are the odds of getting two defective wiring harnesses—pretty slim. After another couple hours of trouble shooting with my mechanic, I am embarrassed to admit I misread the fuse diagram for my Odyssey. I had installed the fuse for the wiring harness in the wrong location in the vehicle fuse panel. The darn think works just great now. Hats off to the people at Etrailer for this top-shelf service—when it was really my mistake.
Very easy to install. I did not like the idea of the wiring just hanging in the trunk area, so I cut an opening into the storage compartment on the side trim panel so I could feed the wiring into it and keep it there when not in use.
John O.
7/13/2013
did the same thing. worked well. Thanks for the idea.
Easy installation, took approx 25 minutes or so. Pulled back trim and plugged in... EASY. Came with everything I needed including fuses, twist ties, and adhesive for unit.
Must difficult part was making sure I could find the right fuse locations in the car to add.
Bought with receiver kit. Whole installation took approximately 45 minutes (a little longer to make sure wiring was put in place).
2 days later used it unexpectedly to retrieve friend's broken down vehicle... worked great!
Bob I.
7/22/2020
Sill working out great! Durable, no problems using, it has more than paid for itself.
Worked perfectly for my 2015 Honda Odyssey minivan. Easy to install. I popped out the auxiliary power port in the panel near the plug and enlarged the hole enough to get the adapter through and then replaced the plug. The wiring now sits neatly in the side bin when not needed.
Easy install, works as described. Wish there was an easy way to hide or keep wires out of the way, but that is on me. Also like that etrailer is asking me for a review a year later, which gives me more confidence in reviews I read.
Love your website it lead me right to the kit for my car. I also watched your YouTube video. I installed the kit in less than 20 minutes. Great product and great website. Also thanks for reasonable shipping rates. You guys rock!
The wiring harness lasted less than 2 years. No fuses were blown, the diodes in the Curt controller just stopped working - sending a low voltage to the trailer lights all the time. This is the second Curt trailer wiring harness that has failed on my vehicles.
Haven't opened yet. Harness in box? Excellent service, time order to delivery.
Once the wiring harness arrived, it was installed in less than 20 minuets. Tested it out on the trailer and everything worked great. If I need sports in the furture, this is the first place I’ll look.
Thank you
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Roy
5/15/2013
Great idea - I did the same thing, thanks! Installation was very easy, under 30 minutes start to finish.