Erickson E-Track Tie Down Ring - 1,200 lbs
(827 reviews)
Price: $10.05
In Stock
Erickson E-Track Tie Down Ring - 1,200 lbs
Item # 59131
Retail:$23.71
Our Price: $10.05
You Save: 58%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (827)
- Q & A (0)
- Videos (2)
- Photos
Erickson E-Track - 59131
- E-Track Anchor
- 1200 lbs
- Erickson
Attaches anywhere along e-track to provide a tie-down point where you need it. Push-button design makes it easy to move and secure.
Features:
- Tie-off Ring
- 4,000 lbs Capacity
- Safe Working Load Limit: 1,200 lbs
- Color may vary
- Not compatible with Snap-Loc E-Track Tie-Down Anchors
Note: Tie-down anchors must be chosen according to their safe working load limit (WLL). The weight of the secured cargo must not exceed the combined WLL of the anchors being used. For example, if you are using anchors with a WLL of 100 lbs each to tie down a load weighing 400 lbs, then you need at least 4 anchors to safely secure that load. It is recommended that you always use anchors in pairs.
59131 Erickson ETrack Tie-Off Ring - 4,000 lbs
Video of Erickson E-Track Tie Down Ring - 1,200 lbs
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Erickson Tie Down Anchors - Trailer Tie-Down Anchors - 59131 Review
Today we are going to show you part number 59131 from Erikson. This is a part to our E-Track. This is an E-Track D-Ring which is rated at 4,000 pounds. It will fit on all traditional E-Track systems. We will go ahead and show you how it works. All you do is pull this little tab back and it snaps into place then you can tie off what you want to it. You can even attach a regular tie down to it. That is it for part number 59131 from Erikson the 4,000 pound D-Ring.
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Product did not meet expectations
- etrailer mistake
- Wrong item was ordered
Customer Reviews
Erickson E-Track Tie Down Ring - 1,200 lbs - 59131
Average Customer Rating: 4.9 out of 5 stars (827 Customer Reviews)
Attaches anywhere along e-track to provide a tie-down point where you need it. Push-button design makes it easy to move and secure.by: Penny12/11/2022
Great for my home gym. Sturdy. Low cost. Vertically mounted the Erickson Horizontal E-Track and used the Erickson E-Track Tie Down Rings with carabiners for easy height adjustments and swapping out different bands, just like at Fluid Health & Fitness where I take classes and work with a Movement Specialist. The 1 x 4 board is screwed to a wall stud and then the E-Track is attached to the board and into the sheet rock. The Man of the House says he "over-engineered" it. ??
by: Nicholas 08/09/2023
Easy to attach and use with generic cargo straps. I have used these tie-down rings for several interstate trips hauling light cargo and motorcycles with no problems. Large ring allows easy threading of cargo straps and attachment of strap hooks.
by: Matt S12/12/2013
As requested, here are some pics of my e-track installation. I find the raised e-tracks in the floor very problematic and dangerous so I made sure they were recessed. This is now an extremely versatile cargo trailer.
by: Bob B. - etrailer.com Employee12/26/2013
Let me just start by saying I Love etrack! These tie off rings make loading the truck and trailers quick and easy. I even installed a couple on the side of my tailgate so i could strap down longer items when tailgate is open. (Dont forget to remove the ring when done and closing tailgate)
by: David, SMSgt, USAF12/28/2010
the BeastAttached are pictures of the "Beast" The truck and trailer are utilized to
haul a miniature C-130J aircraft in support of Air Force Reserve recruiting
activities in Louisiana, Mississippi, and Alabama. We exclusively use
etrailer.com for our E track straps and D rings.
by: Kay02/13/2023
Missing items due to packaging not secure and damaged box
by: Rick10/14/2016
Best cargo anchors. Use them a lot on both my cargo and utility trailers....Shipping costs are nominal compared to other sites....
by: Darius05/01/2023
Just recieved my order today. Do not have the hooks installed yet but, they appear to be everything I was looking for when I ordered them. Well built and work in the tie down railings very well.
Very prompt order and delivery. Will be ordering more equipment in the future.
by: Doug l07/18/2017
Perfect for strapping down anything in your trailer with easy tracks
Doug L.
7/18/2018
Still working like day 1.
by: RONBO02/25/2015
I've used these Erickson E-Track tie-off rings for many years in all my other trailers. I bought a new trailer and therefore, needed new tie-off rings. These units are the lighter version of ring available from Erickson and I've used both types to secure my ATVs. I've never had any problem with either tie-down. These units are plenty strong enough to hold any ATV, motorcycle. In fact, I've hit terrible potholes and other obstacles with my trailers over the years, that I've had ATV's pop the tie-down straps off. However, no matter how hard the jolt, I've never had one of these Erickson rings pull lose, bend, crack, or any other malfunction. In addition, they are super easy to remove, reposition, attach etc. They lock into position as soon as they are fully inserted into the E-tracks sytem.
Ronbo
3/10/2016
Thanks for the follow-up. All the products I purchased are performingwonderfully!
by: Jim MC987610/06/2014
I think these E-Track tie rings will work out perfectly. In another review, I review the E-track Wood Beam Sockets and how I made a tire rack and shelves in my car trailer using the E-Track which I also bought from E-Trailer.
I'll use these E-Track tie offs to tie down the tires, and any loose items on the shelves, so that they don't bounce around which on the road. It'll be a breeze to use either some straps or rope to tie down anything I need to, and having the flexibility to position these tie downs anywhere I want on the E-track, is absolutely perfect.
I also thought that they were priced fairly and made well. Add to those qualities all the benefits of doing business with E-Trailer and it's a home run!
Jim M.
10/6/2015
As I thought, these E-track tie down rings worked out perfectly. Nothing has ever fallen, bounced, or even moved pout of place when straps are used to secure the load to these E-track rings.
by: Charles06/26/2023
Easy in and easy out. Perfect for my constantly changing trailer needs.
by: James/ Disabled American Veterans Chapter 302/19/2023
We use them almost every day we go out to pick up donations and need to secure the items we are hauling.. They come in handy when we need to move them to another location within the trailer that we are using..
by: Richard 09/28/2022
I Installed approx 14 feet of e track Two rows long in my enclosed trailer to go under my tires for my side by side. It has worked out better than expected as I can secure things down the entire length of my trailer . The side by side is secured with wheel bonnets and does not move one inch while traveling from my place in Utah to my place in Wyoming. Love this product and highly recommend .
by: david04/20/2021
We've finally been able to install the etrack in our trailer and it looks, and works, great. I've attached a few pictures we took of the installation.
by: Jan 04/06/2023
Survice and product knowledge and made in USA
by: Chris07/18/2023
Excellent product
by: John N05/28/2014
Awesome idea! These are great to have with the E Track system!!!
by: Ron03/15/2023
All of the products I have ordered from etrailer have been exactly what I was expecting, and they have performed flawlessly.
Thank you!
by: Norman 07/06/2023
Work great
by: Dave B.07/18/2016
I have a 20 ft enclosed cargo trailer that I planned to use to move from California to North Carolina. Was not sure about how to secure the load. Did some research and settled on the E Track system. Not having ever used E Track before, I found the instillation and use very simple. I installed two rows on each side the full length of the trailer. In the front I used the optional E track board holders and made a shelf 8ft by 4ft with 2 x 6's and a full sheet of plywood to secure fragile items. Two trips across the United States with very full loads and not one load shift. Great product and would highly recommend it. Thank you etrailer.com for your great service.
Dave B.
7/25/2017
A year and a half later and a lot of use out of my trailer using the E Track system to secure the loads. Great produce that was easy to install and easy to use. HIGHLY recommend the E Track system.
by: Tommy04/21/2016
Excellent product! I bought 2 of the 4-ft e-tracks. These are heavier duty than I thought they would be. They are extremely practical for my 10' wood floored utility trailer. If you are like me, there aren't many good tie down points on wood bottomed trailers. These are an easy fix for a host of applications. They work great for having multiple points to tie down my 4-wheeler or lawnmower. I will definitely recommend! The only better would have been free shipping.
by: Michael 06/29/2023
Great job getting me the needed parts
by: Dallas 07/13/2022
These e-track tie-downs are extremely useful for securing loads in our overlanding trailer for off-road driving. Small, compact, strong and flexible location on the track. Glad to have them.
by: Kaas Baichtal07/26/2016
These feel a bit cheap and cheesy but they work great. I had installed E-track lengthwise (front to back) on the floor of my trailer and have a lot of need to tie loads with diagonal and/or track to track forces and these worked great for that, since they seem to be pullable in any direction without deforming. The heaviest item I fasten down is a walk behind lawn mower.
Kaas B.
7/26/2017
We still use these a lot and are still on our original ones. All other latching items we got for the e-track bent too easily but these are great.
25
804
Show More Reviews
See what our Experts say about this Erickson E-Track
- Would 8 of the Erickson Tie Down Anchors 59131 Have Weight Capacity for 1,200 UTVEach of the Erickson E-Track Tie Down Rings part # 59131 have a 1,200 lb capacity. With several of these your 1,200 lb Wolverine would be secured well.
view full answer... - Tie Down Ring/Anchor that Fits Ford Box Link in F-350 BedYes the E-track accessories like the Tie Down Ring # 59131 do fit in the BoxLink cleats in the bed of Ford trucks like your 2018 F-350.
view full answer...
- How Does Etrailer Slot and Anchor Typically Install on Truck TailgateSounds like you are talking about using a single E-Track slot like part # SLSB to instal the Erickson E-Track Tie Down Ring # 59131 in a tailgate application like the picture we recieved from a customer who did the same. There isn't an exact recommended way to accompolish this. It looks like the picture you referenced has a tailgate that has an internal panel that can be removed so that the customer could use nuts and bolts to hold the slot to the side of the tailgate. We don't have exactly...
view full answer...
- Length and Width of E-Track Tie Down Anchors 59131 and 59147I went and pulled both the part # 59131 and # 59147 from our warehouse to get the dimensions you requested. The width of both measures 7/16 inch. The overall length of the part # 59131 where it clips down into the e-track is 2-13/16 inches. That portion of the # 59147 measure 2-3/4 inches.
view full answer... - Is it Possible for E-Track and Snowmobile Carbides to Scratch Each OtherFrom what I understand about snowmobiles, and please correct me if I am wrong because I have little knowledge on them, the carbides are the part the skis attach to. Is that correct? I am not sure how the E-track or the carbides would come into contact with each other. But if they did then it would be possible for one to scratch the other. To avoid that you could use 3 lengths of tracks; one on the far left side and one on the far right with one in the center between the snowmobiles so...
view full answer... - Can the Erickson Horizontal E-Tracks Be Mounted On a Ceiling for Punching BagE-track can be used on a ceiling since it is designed to hold quite a bit of weight to the track. Commonly people secure vehicles to the track on the floor of a trailer so a ceiling mount (through a stud) to hold a punching bag would be definitely doable. For an anchor with a ring to use with the track # E19148 you'd want just the part # 59131.
view full answer... - Side Pull Capacity of Erickson E-Trick Tie Down RingsAccording to the folks at Erickson Manufacturing, the side pull capacity of their # 59131 E-Track Tie Down Rings are 1750 lbs apiece. The safe Working Load Limit for each would be 1/3 of that which is about 580 lbs apiece. It looks like you're using 4 of the tie down rings which would have a combined capacity of 2320 lbs which is plenty for the quad you have tied down, assuming that the straps you're using have sufficient capacity.
view full answer...
- Will E-Track Tie Down Anchors Fit in Snap Lock Horizontal and Vertical E-TrackYes, the Erickson E-Track Tie Down Ring item # 59131 you referenced can be installed in the Snap-Lock Horizontal and Vertical E-Track item # SL27FR. Those Tie Down Rings can handle quite a bit of weight but it is going to come down to the anchors you are using to attach the vertical E-track to determine how much capacity they can handle.
view full answer... - Will Erickson and US Cargo Control Accessories Work With etrailer Horizontal E-TracksI can't confirm US Cargo Control as this is not a brand we carry but the e-track fittings are fairly standardized so you should be able to use any brand designed for e-tracks such as the Erickson E-Track Tie Down Ring part # 59131 with the etrailer Horizontal E-Tracks like part # e62VR
view full answer... - Will E-Track Tie Down Anchors Fit in Snap Lock Horizontal and Vertical E-TrackYes the e-track tie down anchors like the # 59131 can be installed in the Snap-Lock Horizontal and Vertical E-Track # SL27FR that you referenced. Basically any e-track accessory will fit in the # SL27FR that you referenced.
view full answer... - Can Buyers Products Sliding Winch Track Be Used as Trailer Tie Down AnchorYes, the Buyers Products Sliding Winch Track # 3371903040 can be installed on a flat steel surface to secure a load, as you mentioned. Since it's designed to allow a winch to slide along that channel, for this purpose, the channel must face down. However, installing it with the C-channel facing up does not affect its functionality for your application. That being said, I believe the Erickson Horizontal E-Track - Zinc Plated Steel - 2,000 lbs - 5' Long # E19148 will work much better for...
view full answer...
- E-Track and Motorcycle Wheel Chock Recommendation for Securing Motorcycle to TrailerThat sounds like a great plan, the E-Track part # E19148 will provide a great tie-down point for securing the motorcycles. For tie-down rings you would want the # 59131 and then for a wheel chock I would recommend the # 3481731 because of how well it secures motorcycle and how easy it is to use. Check out the review video I attached for more info.
view full answer... - E-Track Recommendation for Securing ATV to Utility TrailerE-track can easily attach to the wood floor you have in your open utility trailer. This is a very common style of trailer that is used with the E-tracks. I attached a couple review videos that show etracks installed in a similar trailer as yours and what they use to secure the cargo. The etrack sections like the part # E19148 would be more than adequate to secure your ATV. The # 59131 is a great anchor to use, or if you want a strap that attaches directly to the etrack we have the # EM59136...
view full answer...
- E Track Placement Recommendation for Motorcycle TrailerBasically you'll have to mock up where you want the motorcycle to be and where the best place will be for the e-track as there isn't a set place to install the tracks in every trailer. Typically you want the tie down anchors to be about 36 inches apart from each other to get the best angle for them to pull down. For tie down anchors that fit in the e-track slots we have the part # 59131 which would fit and work well. Then for a set of ratchet straps the Erickson kit part # EM31353 would...
view full answer... - Recommended Erickson E-Track System for Transporting Motorcycle in Enclosed TrailerInstalling the Erickson Horizontal E-Track # E19148 in your enclosed trailer is an excellent idea. Along with securing your motorcycle into place, the E-Tracks will provide great versatility to tie down various other cargo items in your trailer. For your motorcycle, I recommend installing the tracks on either side of the motorcycle to provide multiple tie-down points in order to keep it secure. Then you can use the Erickson E-Track Tie Down Rings # 59131 along with D-Ring Straps # E59143...
view full answer... - Option to Carry Kayaks with E-Tracks Inside Cargo TrailerI am not aware of an e or x-track accessory that is designed specifically for carrying kayaks but we do have options for this assuming the tracks are on the walls. I recommend using a few CargoSmart Large Rotating Flat Hooks part # 3481701 to suspend the kayaks and then a few Erickson E-Track Straps with Ratchet part # EM59136 to hold them in place. The Erickson E-Track Tie Down Ring part # 59131 along with some standard ratchet straps can be used as well.
view full answer... - Length of Buyers Products Super Track KitThe Buyers Products Super Track Kit # 337ST93 only comes in a length of 46-1/2 inches, or just under 4 feet. There is a 5 foot length of E-Track, the Brophy Horizontal E-Track # ET05 which will allow you to use the Erickson E-Track Tie Down Ring # 59131. I have added a link to a video review of the Buyers Products Track Kit for you to take a look at.
view full answer... - E-Track Recommendation to Secure 4 Motorcycles in an Enclosed TrailerYou would be more than okay to run two tie downs off of one the E-Track Tie-Off Ring part # 59131 that you referenced. Each of these has a 4,000 lb capacity which would be more than enough for what you are doing. Your plan to use 9 of the E-Tracks # EM59150 with the # 59131 like the drawing you sent in would work perfectly. For backing plates you could use the part # e96RR. I attached an install video for the E-track for you to check out as well.
view full answer...
- Compatibility of Erickson ATV E-Track Tie-Down Kit EM09160 with Brophy Backing Plate BPEZErickson E-Track fittings like the Tie Down Ring # 59131 will work just fine in their ATV E-Track Tie-Down Kit # EM09160. Please note you will supply appropriate installation hardware for the ATV kit based on the requirements of the mounting surface where you will install it. The four outside holes on the etrailer plate # e96RR do generally align with the mounting holes on the ATV kit but we have found that it may sometimes be necessary to enlarge two of them to get the best fit. Just...
view full answer... - Single E-Track Anchor for E-Track Tie-Off Ring # 59131In the picture, the customer is using the Erickson tie-off ring # 59131 with single E-track anchor, # SLSB. There is also a stainless model, # SLSS, and a zinc model, # SLSZ. If you want one you can paint yourself there is also an unfinished model, # SLSU. I have linked a couple of videos to the right for you. There are all kinds of E-track accessories that could be used in the anchors. I have also included a link with the accessories, anchors, and tracks for you.
view full answer...
- Can the Erikson E-Track System Be Used In An Aluminum Utility TrailerThe Erickson E-Track system will work great in your aluminum utility trailer, but you will want to put a layer between the E-Track and the aluminum of your trailer. This layer will help prevent corrosion cause by contact of dissimilar metals. This layer can consist of almost any material, such as wood, rubber, or plastic. When installing the E-Track system in a trailer, one thing to keep in mind is to select locations that provide structural components, such as wall studs and floor supports....
view full answer... - Custom Fit Mud Flaps for 2019-2020 Ram 1500 Limited With Fender Flares Front and RearFor the 2019-2020 Ram 1500 Limited you have that has fender flares the correct fitting front mud flaps are the # HL58131 and then for the rear # HL59131. These will look and function great on your truck and since they are custom fit the install is pretty simple too.
view full answer... - Available Lengths of Erickson E-TracksUnfortunately, 5 feet is the longest Erickson e-track we carry and is # E19148. They also come in 2 foot # EM59150 and 4 foot # EM19147 lengths. They can be cut to the needed length.
view full answer... - Tie Downs and E-Track Recommendation for Securing a BMW K1200, ATV, and Dirt Bike on a TrailerI would recommend using 2 sections of Horizontal E-Track, # E19148, down each side and 2 sections of Horizontal E-Track down the middle of your trailer, 6 sections in all, to give you as many tie down options as possible for securing all of your different toys. Your BMW K1200 sounds like the heaviest item you will need to tie down. I recommend using 2 packages of the Retractable Ratchet Straps, # 34414, along with 4 of the E-Track Tie-Off Rings, # 59131. Four tie down points are needed...
view full answer...
Do you have a question about this E-Track?
Info for this part was:
Expert Research:
Jameson C
Video Edited:
Dustin K
Installed by:
Cole B
Updated by:
Jacob W
Updated by:
Alex H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Jenny N.
2/13/2023
I will have our Customer Service team contact you.