Metal Loom Clamp - 1/2"

See what our Experts say about this Redline Electrical Tools

• Rewiring Boat Trailer for 7-Way to Use LED Lights
  There are a number of things you will need if you want to re-wire your boat trailer to use LED lights and you should start with Junction Box # 3375601100 and 7-Way # HM20041. Keep in mind you will also need Ring Terminals # 44-5310A and Loom Clamps # A0500 For LED lights I highly recommend checking out the LED Trailer Tail Light # STL57RB (Driver's side) and # STL56RB (Passenger's side). These are submersible lights with a total of 40 diodes and have mounting holes that are 2" center to...
  view full answer...
  
• Troubleshooting Trailer Tail Light That Stays On With Trailer Uncoupled and Wiring Disconnected
  Since your trailer lights are getting some power even when the trailer is not hitched and not connected to the tow vehicle wiring this tell us that one of the batteries on the trailer, either the auxiliary battery for the lights or the breakaway battery for the trailer's electric brakes, is somehow leaking power to the lights. Most likely there is a short on the power leads to one (or possibly even both) of the trailer batteries. You can inspect all of the breakaway and auxiliary batteries'...
  view full answer...
• Recommended Hitch, Wiring Harness, and Brake Controller for a 2013 Toyota Highlander
  I would be happy to help you set up your 2013 Toyota Highlander for towing. I will start by confirming that the etrailer Trailer Hitch Receiver item # e98858 does fit your Highlander. Since you do not have any vehicle connectors at the rear of your Highlander you will need both item # HM11141845 and item # ETBC7 to add a 7-way connector. The Tekonsha Prodigy P3 Trailer Brake Controller item # 90195 is one of our most popular brake controllers and is highly recommended. I have linked a...
  view full answer...
  
• Recommended Installation Screws for 1/2 Inch Metal Loom Clamp # A0500
  For the Metal Loom # A0500 you will want to use the self-tapping screws like the part # FA1131822. The nice thing about this screw is that it doesn't require a pilot hole, just line it up and let the drill bit end of the screw do the work for you. This threaded screw will secure your loom clamp securely on your trailer. I have linked the above mentioned products to this page for your purchasing convenience.
  view full answer...
• Is The 1/2" Metal Loom Clamp # A0500 a Single Component Or Multiple Clamps?
  The price for the 1/2" Metal Loom Clamp # A0500 is for a single clamp. We do have the Clamp Kit # PT43VR which includes (20) 1/4", (8) 5/16", (6) 3/8", (4) 1/2", and (4) 5/8" clamps if you are going to end up needing a variety of different sizes.
  view full answer...
• Compatibility Of 1/2 Inch Loom Clamps With 3/8 Inch Loom
  Yes, you can use Metal Loom Clamp - 1/2" # A0500 with Wire Loom 3/8" Diameter # 39035. It will secure the loom to your frame but it will not clamp tightly around it. If you want a tight fit at the clamps you can use 3/4" x 60' Electrical Tape to close the loom at that location and make it your desired thickness for clamping. If you want a perfect fit, I recommend the Wire Loom, 1/2" Diameter (per Foot) # 459075-1.
  view full answer...
• Screws to Use with the Wire Loom Clamp part # A0500
  You would want to use some self-tapping screws like the part # FA1131822. These would not require you drill a pilot hole. Just line the screw up where you want it through the Loom part # A0500 and let the drill bit end of the screw drill the needed hole and the threads will pull it through and secure it.
  view full answer...
• Does Titan Brake Line Tee Secure Trailer Brake Lines
  Indirectly yes, the part # T0778500 does get used with brake hoses. If you check out the attached picture you'll see that holds a union tee that hoses run to. We do have clamps that were designed to secure brake lines like with the part # A0500 for 1/2 inch and # A0250 for 1/4 inch. We also have clips, # T0936600, for more brake line support.
  view full answer...
  
• Will the 1/2 Inch Metal Loom Clamps Work On a 5/16 Inch Frame Rail
  Yes, the Metal Loom Clamp part # A0500 will work on a trailer frame that is 5/16" thick. The Metal Loom Clamp will actually work on pretty much any frame thickness but you will need to make note of the size screw used. I recommend the Hex Screw part # 101131802 for a 5/16" thick frame as it is 1/2" long. The Wire Loom part # 459075 can then be added to protect your wiring. I have attached a list of our other wiring accessories for you below as well.
  view full answer...
• Wire Loom Clamp/Clip Recommendations for 4-Way Wiring.
  Based on our customer reviews it looks like the Wire Frame Clip # CE16867A that you referenced has better reviews than the Wire Frame Clip # 464600. Either one should work fine, but if it were me I would go with the # CE16867A between those two. Another option is the Metal Loom Clamp # A0500. You will need to provide some self tapping screws but this is the loom clamp that our installers here at etrailer use the most. These clamps are rubber coated to protect the wires and since they screw...
  view full answer...
• Electric Brake Conversion from Air Brakes on 15,000 lb Axle Trailer
  The Dexter Electric Brake Kit w/ Cast Backing - Self-Adjusting - 12-1/4" - Left/Right Hand - 15K # 23-446-447 will fit any 15K axle that have the standard 7 bolt mounting flange. These are self-adjusting brakes so there is no need for manual adjustments after the initial installation. They are labeled left-hand (driver's side) and right-hand (passenger's side) to ensure proper placement. If you need the mounting hardware, I recommend # BRKH122510 for each axle. You will also need...
  view full answer...
• Replacement Wire Loom to Secure RV Slide-Out Wiring
  Thanks for the photo, that was a huge help! You're needing 1/2 inch wire loom, which we sell by the foot as part # 459075-1. I'd also use some 1/2 inch loom clamps, part # A0500 to secure the wire loom and hold it where it's supposed to be.
  view full answer...
  
• Availability of Wiring Clips to Attach to I-Beam on EZ Loader Boat Trailer
  The CE Smith Trailer Wiring Clips # CE16867A referenced in your question will fit around edges that are up to 5/32 inches thick. I am not sure how thick the I-beam is on your EZ Loader Boat Trailer but we do have the slightly larger # 464600 Clip that will work with a frame thickness of up to 5/16 of an inch. I recommend simply measuring the thickness on the beam to see if one of these options will work. If the I-beam is too thick for either of these options then your best bet will be...
  view full answer...
• Replacing Trailer Wiring on a 2000 Jayco 17 Hybrid
  It sounds like the best solution for you is to bypass the existing trailer wiring since you cannot locate the wiring that leads to the tail lights. You can use wiring # 16-4B-1. It is sold in increments of 1 foot. So if you needed 20 feet you would enter 20 in the quantity box. Or you could replace the connector as well. If you have a 4-Way you could use # A35W42B which has 2 running light wires, one for each side of the trailer. If you do not have a 4-Way you could tell me the connector...
  view full answer...
• How Is the T-Fitting for Trailer Brake Lines Mounted Without Integrated Bracket?
  There are a couple of ways to mount the Kodiak Tee Fitting for Hydraulic Brake Hose - Brass - 3/16" Female Inverted Flares # BH-T-3FIF. Many will use brake line mounting hardware on either side of the brake line which will provide enough stability like you see in the # 20TA-BLKIT pictured. Others want more of a direct mount like you are seeking use the metal loom clamp # A0500 directly on the T-fitting itself to give you that solid mount and then add extra clamps further down the brake...
  view full answer...
  
• Frame Clip Size and Styles Available
  The height of the Wire Frame Clip, item # 464600, is 1-1/2 inches, width is 1/2 inch, width for wire capacity is 3/8 inch and the frame depth is 5/16 of an inch. Constructed of spring steel and has a black enamel finish. Metal Looms are also available and we have the 1/2 inch, item # A0500, and the 1/4 inch, item # A0250, which are installed usually with self tapping screws.
  view full answer...
• Clips and Clamps to Attach Wires and Wiring Harnesses to the Bottom of a Trailer Frame
  There are many ways you can secure wires to a trailer. I would not recommend the use of tape as it will wear out quickly when exposed to the elements. Soldering is also not recommended because it is a more permanent method and you may need to change wires or move them in the future the hot solder would also melt the coating on the wiring, causing a short. If you can find some large enough, wire ties could be a simple solution. We have several clamps and clips that could work for this application....
  view full answer...
• What Type of Steel is Used in the Metal Loom Clamp A0500
  The wire loom part # A0500 is a zinc-coated steel. The zinc coating fights rust to prevent corrosion.
  view full answer...
• Instructions for Completely Rewiring a 14 Foot Tandem Axle Dump Trailer
  Rewiring your 14 foot dump trailer is pretty straight forward. I would start with a 20 ft. Wishbone 4-Way Trailer Wiring Harness, # A20WB, to provide wiring for the stop turn and tail lights on your trailer. We have a video detailing how to install this type of harness for you to review, see link. Next, I would use the RV-Style Trailer Connector, # PK12706, and remove the 4-Way connector from the 4-Way harness and install the wires in the proper locations in the 7-Way connector. Our wiring...
  view full answer...
  
• What Gauge Wire Can the 3/8 Inch Wire Loom Hold?
  3 gauge wire is about 0.229 inches in diameter, so Wire Loom 3/8" Diameter like # 39035 will give it enough space for safety without further restricting the wire for heat dispersion. It will also avoid pinching or crimping the wire. You can use the Metal Loom Clamp - 1/2" # A0500 to secure it if desired. Technically this loom could hold up to 00 gauge wire (0.365 inches diameter).
  view full answer...
• Wireless and Wired Brake Controllers for 2019 Toyota Tundra with Factory 7-Way
  At this time (June 2019) we do not have any trailer brake controllers that offer under-dash plug-and-play installation in your 2019 Tundra with factory 7-way/4-pole. We do offer the no-wiring-needed Curt Echo controller # C51180 which requires only a working 7-way vehicle socket at the bumper and a compatible smartphone that serves as the display and control device. The Redarc Tow Pro Elite # RED44FR can be installed in your 2019 Tundra but it will need to be hardwired. If you refer to...
  view full answer...
  
• What is Needed to Tow a M105A2 Military Trailer with a 2013 Dodge Durango
  To convert your M105A2 military trailer to a 7-blade, I would recommend using the Epicord 7-Way with Junction Box # 277-000141. This makes the conversion simple and you don't have to worry about wiring the connector itself. You'll also need some ring terminals like # 44-5310A and some loom clamps like # A0500. The wires in the junction box are color coded as indicated below. Military wiring is typically not color-coded, so you may need to use a circuit tester like # PTW2992 and a 12V power...
  view full answer...
• Replacement 4-Way Wiring Harness for Trailer That Will Last More Than 2 years
  Hi Don; for a replacement 4-way wiring harness I recommend the 20 Ft 4-Way Trailer Wiring Harness # A20WB. This is a wishbone harness so you can run wires down both sides for your marker lights. Regarding the longevity of the wiring, I don't have anything I can say will last more than 2 years for sure but such a short timeframe isn't typical. Since you seem to be having some issues with your old wiring I would use a cover # C58750 to help protect the new connector. I would also make sure...
  view full answer...
• Wiring and Lighting Component Recommendations to Re-Wire Tandem-Axle Car Hauler Trailer with 7-Way
  A junction box like the Spectro # 38656 is a perfect way to re-wire your tandem-axle car hauler. This box provides plenty of room inside its weather-proof housing to make all of your lighting, 12V and brake signal connections. Please refer to the linked video. We use this box on just about all of our in-house re-wiring jobs. You'll also want to use ring terminals like 3M part # 44-5310A for all of the junction box connections; these will both save you time and provide longer-lasting connections....
  view full answer...

Do you have a question about this Electrical Tool?