To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Install this heavy-duty hitch on your vehicle so that you can securely tow your gooseneck trailer. Store the removable ball upside down in the hitch when you aren't towing to get complete bed access. Square ball base won't turn in hitch.
Features:
Specs:
With the B&W Turnoverball underbed gooseneck trailer hitch you get the best of both worlds. When you go to tow, the Turnoverball creates a sturdy, dependable connection with your gooseneck trailer. And when you're done towing, you can stow the ball upside down in the hitch to get full bed access and a clean appearance.
The durable steel hitch ball included with the Turnoverball system secures in the hitch with a sturdy, 5/8" thick steel pin that is incorporated into the end of the operating handle. To lock the ball in place, drop it into the hitch hole in the bed of your truck. Then rotate the handle in your driver's-side wheel well counterclockwise until the latch engages. When the latch is engaged, the spring-loaded pin on the end of the handle will be inserted all the way through the base of the hitch ball, forming a strong, solid connection and ensuring absolute security when you're towing.
When you're done towing, remove the hitch ball by simply pulling the handle out as far as it will go and then rotating it clockwise until it unlatches. Remove the ball, flip it upside down, and drop it back into the ball hole of the hitch. Then reengage the latch to secure the stowed ball in place.
Unlike typical gooseneck balls - which have round bases - the Turnoverball hitch ball is designed with a square base. This makes latching the ball in the hitch easier because the base won't rotate inside of the hitch like a round base might, so lining the pin up is a snap. The base of the ball also fits tightly within the ball hole during storage. Because only the corners of the base contact the sides of the socket, any dirt or grime that gets into the hitch will fall through the socket, thus helping to prevent any buildup that could cause the ball to seize up in the hitch.
Simple, Custom Installation
This hitch is custom designed for your vehicle. The included mounting brackets bolt to existing holes in your truck's frame. While some modification is required - you will need to cut a 4" diameter hole in your bed for the hitch ball and drill holes for the built-in safety chain loops - there is no need to weld onto or to drill into your frame.
Once you have the hitch brackets and body installed, set up the operating handle. This handle is designed to be accessed from the rear driver's-side wheel well. On the end of the handle is the heavy-duty steel pin that secures the hitch ball.
B&W makes it easy to tow just about anything. With the many adapters and accessories available, the Turnoverball can be made to work with almost any gooseneck trailer. Hitch balls are available that have a built-in rise, an offset, and even a different connection type. Add on the Companion fifth-wheel hitch - which attaches directly to the Turnoverball with no other parts required - and you can tow your fifth-wheel trailer.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (3794 Customer Reviews)
Install this heavy-duty hitch on your vehicle so that you can securely tow your gooseneck trailer. Store the removable ball upside down in the hitch when you aren't towing to get complete bed access. Square ball base won't turn in hitch.
I love my hitch . I love how I can turn it over and I can still have use of the full truck bed. I could of bought a cheaper hitch but the quality is by far better than other hitches I have owned in the past. Customer service was great after they helped me fix my ordering mistake. Very happy with my hitch.
I was very satisfied from ordering to instillation. Great people and very concerned about your satisfaction. Instructions were complete and easy to follow. Saved approximately 50% in cost. Thanks etrailer
Instructions with hitch were very good and assembly went flawless and hitch also works great.
Teresa and Jane are awesome people to communicate with. Teresa had the correct hitch number I needed,but since I had talked to B&W and gotten a different # to order we decided to go with that one. Cost me $103 to send it back to get the correct one ,that I worked with Jane to get. I am very happy with the fact I can go camping now and wish I would have just listened to Teresa and Jane was awesome too.
Was little difficult to under stand instructions to install, but then we figured it out. Has worked great ever since.
Have had NO Problems with it. Took a little effort to get it installed but was worth the extra time. I have not been dissatisfied in the least.
Great product. Easy to install. Easy to use and easy to flip over when I need a flat box to haul or clean out the bed of my truck.
Instructions were easy to follow install went smoothly
Simple and EASY ordering Steve stayed in touch every step of the order product until delivery was made I have used them before ALWAYS GREAT
This will be the 3rd pickup I've installed a B&W flip over and recommend them highly
Everything worked out great the only problem is the handle to pull the pin out is not long enough to go outside the wheel well so I had to add three more inches onto it other than that great product thank you very much
I purchased this to pull a 25Ton GN trailer with heavy equipment and so far it works great! Good price point and reliable product. I would highly recommend this product and trailer. Thank you!
Installation was straight forward and it's well built. Works smoothly. etrailer was awesome as usual with shipping and service.
However.... ;) on the BWGNRK1400 for '73-'87 GM trucks, the predrilled holes in the hitch for the safety chain u-bolts are 6-1/4" each way from center of the ball. This places the matching holes you have to drill in the truck bed on the sloped edge of the ribs, not in the center of the valley as intended. The instructions read as if the holes are not pre-drilled but they are, so I contacted B&W and asked if I can drill new holes at 8-3/4" each way of the ball so that they center in the next valley and they said no, that will void the warranty. So I had to do some bodywork, cut, weld and grind to scallop the ribs around the anchors to they won't always be sticking up (defeating the flat floor intent of this hitch design). I saw guy on [online] noted this was an issue on his squarebody bed as well.
B&W needs to look at this dimension for future installations to help out the next guy.
Great hitch! I'm a pretty avid do it yourselfer so I did the install myself and it was relatively simple. The directions that came with the hitch had all the information I needed. It works well with my trailer and the quality seems to be pretty good. It's pretty low profile while you're not using it as well. Overall very happy with it. A couple of install notes for squarebody Chevy, GMC trucks which is what I installed mine on: You will need to lift the bed off the frame just enough to slide the hitch between the bed floor and the top of the frame rails so if your truck is rusty like mine, you may want to have new bed mount hardware on hand before you start in case you have to cut the old bolts to get them out. Also, the safety chain loops land right on the ridges in the bed floor so they don't recess completely flush even when they're not in use but so far it hasn't been a problem for me. I saw that mentioned in some other reviews on here so I already knew before I bought the hitch.
This was the second Goose-neck mid bed ball to frame assembly I purchased from etrailer....this was for a V-8 Tundra; the first was for a V-12 dodge 2500; Both were absolutely spot on in terms of Hardware provided; Instructions; and actual holes already in the respective frames to line up to the hitch frame mounting steel; beyond that I got digital brake/level controllers from these guys for the Tundra and it was mint....cannot speak more highly of etrailer to get the stuff you need to haul....its obvious these guys actually get the kit first then see if it fits...on an actual truck...then order and distribute it when it does...10 out of 10 for etrailer
Overall this Installation went as I anticipated, 4-5 hours; it's not for an unprepared amateur. I strongly recommend watching the Installation Video, but more importantly, disconnecting the wiring harness (from both sides, there's 3 connectors) that cross over the rear cross member above the Differential. Disconnecting the rear exhaust was a MUST DO for us (my son helped me) as is a second person. Patience was our friend during this entire Installation for both of us. The brake line that crosses over to the passenger side was of concern to me, and got in the way as well; in the end it is below this entire installation. However there is a Mount Block on the driverside that creates a problemwith getting one bolt into place; a "Fishing Spring" (spring wire that wraps around the threads with long tail to fish/thread/pull thru the hole) would have helped to get this into place. (SEE PICTURE) Once in place the head is able to be held with a narrow spanked wrench while tightening. The rear center bolt is a HUGE challenge to reach once everything is in place and you're torquing things to spec.I had to purchase a "3/4" Crowsfoot" to get this and some of the others because of things blocking access with a socket (not talked about in the video or Installation Video). Once everything is in place and Reconnecting electrical plugs we found that there was enough gap/spacebehind the Kit Rear Cross Bar, over the vehicle rear cross member, to run the driver side electrical. Pay attention to have the "male" plug facing inboard to give you enough slack to reach the passenger side plug. A couple of zip-ties were needed to keep this inplace. See picture for how I routed this and the vent tube to avoid the heatshield.
I've got a 26 foot Keystone Cougar 5th wheel RV Trailer that I be using this, along with an Andersen 3217 hitch. With this B&W Hitch I don't have the 5th wheel Rails across the bed full-time anymore of my 2022 Ram 1500DT 4x4.
Great product with good instructions. I was able to install myself. For the lifting of the center piece. I used a ratchet strap and something going across the top of the bed to hold it in place while I was under the truck. Just had it long enough to go through the hole and catch the pin with the hook. I then went into the bed and ratched it up a couple times to fit it in the hole. Worked great as an alternative for extra hands.
After having this hitch for a year I can’t say I’m too impressed. They claim the powdercoat on it is durable, but after only a year there’s already spots of rust. The pictures I’ve included are only showing a few spots I’ve noticed. I painted the pieces that sit against my frame with frame paint in hopes that doesn’t rust either. But the outside facing pieces, I haven’t touched. My truck is stored in the winter and the hitch hasn’t even been used yet since purchase. I’m sure it performs well since my last gooseneck hitch was B&W. But as for durability, I don’t think they do as well anymore. It shouldn’t be this rusty only after a year, being stored, not seeing salt or even being used.
I was converting a fixed/welded gooseneck ball on a CM flatbed to a removable one so I could also use a B&W Companion Flatbed Gooseneck to 5th Wheel Trailer Hitch adapter. Although it wasn’t easy to find someone to cutout the old ball and install the new turnover ball, it was done expertly and the hitch works perfectly! Very easy to operate from the wheel well and turn over for a flat area for cargo. Always had a turnover ball in the past and highly recommend this one for a conversion.
Do you have a question about this Gooseneck Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Harlon H.
3/25/2016
Great