LubriMatic Marine Trailer Wheel Bearing Grease - 3 oz. Cartridges - Qty 3

See what our Experts say about this LubriMatic Lubricants Sealants Adhesives

• What Grease Is Used With the CE Smith Trailer Idler Hub Assemblies?
  The CE Smith Trailer Idler Hub Assembly # CE13315 does come with Calcium Sulfonate grease. We have the Marine Grease # L54FR that is safe to use with their pre-greased hubs. This would require the LubriMatic Mini Grease Gun # 30-800 to use the 3oz tubes.
  view full answer...
• What Grease Is Compatible With the CE Smith Trailer Idler Hub # CE13315?
  The CE Smith Trailer Idler Hub Assembly # CE13315 comes pre greased with a marine formula grease. We have the LubriMatic Marine Trailer Wheel Bearing Grease # L54FR that is compatible with the grease in the hub. You will need a Mini Grease Gun # 30-800 to use the smaller 3oz cartridges.
  view full answer...
• Bearing Kit Options For Tracker Pontoon Boat Trailer With Bearing L44649 & Dexter 010-019 Seal
  Based on what you gave me I can narrow it down to one of two bearing kits for your Tracker boat trailer. Since you mentioned L44610 that means one of the bearings is L44649, and when combined with the Dexter 010-019-00 grease seal, that leaves two options. One is for a 3,500 lb axle and the other is for a 2,200 lb axle, so you can check and see what your axle rating is, which will help decide: - 2,200 lb Axle: Bearing Kit, L44649 Inner/Outer Bearings, 10-60 Seal # BK1-150 - 3,500 lb Axle:...
  view full answer...
• When Should More Marine Grease Be Added To MORryde Wet Bolts
  Hey Brian, Marine grease # L54FR is designed to repel water so you shouldn't need to re-grease the wet bolts of the MORryde Suspension Upgrade Kit # MR76ZR every single trip. It's really going to come down to how long the trailer is sitting in the water and how many miles you're travelling. A 250 mile trip isn't going to run you out of grease. If you're driving a thousand miles I'd probably add a bit more grease to keep everything in good condition and clean out any debris you might have...
  view full answer...
• Is LubriMatic Marine Grease Compatible With LubriMatic 11465
  Hey Malcolm, The LubriMatic Marine Trailer Wheel Bearing Grease # L54FR isn't going to be compatible with the 11465 grease you were using. That said, I do have some good news as that grease is in fact still made and available. What you need is the LubriPlate Poly HP-2 Wheel Bearing Grease # L11465.
  view full answer...
• What Kind Of Grease Should Be Used On Replacement Bushing For Roadmaster Anti-Sway Bar
  Before installing the Replacement Bushing for Roadmaster Anti-Sway Bar, Item # RM-205219-10, be sure to grease the part of the bar where the bushing will be going to preserve the life of the bushing. This bushing does not come with grease so you will need to use something like LubriMatic Marine Trailer Wheel Bearing Grease, Item # L54FR and a compatible grease gun like the # 30-800. LubriMatic is a protective formula that is water insoluble, corrosion resistant, and handles harsh punishment...
  view full answer...
• Should Roadmaster Comfort Ride Leaf Spring Suspension Kit Wear Pads Be Greased
  According to Roadmaster, you can grease the Comfort Ride Leaf Spring Suspension # RM-2460-2570 wear pads if you want to. If you choose to do this, they recommend marine grease like # L54FR. The reason you don't see anything about adding grease or any maintenance in the instructions is because it is not required.
  view full answer...
• Hubs for Timbren Axle-Less Suspension for Use in Salt Water Environment
  Timbren's axle-less trailer suspension systems like # ASR3500S05 are all made with a heavy powder coat finish but it is possible to select matching galvanized idler hubs like # AKIHUB-545-35-G-EZ-K or galvanized hub/drums like # 8-247-50UC3-EZ. Both fit the spindles on this Timbren kit and both have the 5-on-4-1/2 wheel bolt pattern. If you don't mind spending more we also have a stainless steel idler hub from Kodiak, part # KH84545S. All hubs that fit the Timbren kit appear on the linked...
  view full answer...
• New Brake Assemblies, Hub/Drums, Brake Lines, and Bearing Buddy for Trailer with 3,500 lb Axle
  For as trashed as those brake assemblies are I am impressed with how spotless that spindle is! Based on the bearing numbers you mentioned you have a #84 spindle and the hub part # AKHD-545-35-G-K is correct. Since this its galvanized it's a really great option as it will fight corrosion. The flexible brake line kits like the part # 18SI-BLKIT is what I would go with. They are just as durable as anything else and a lot easier to install. The brake assemblies # AKFBBRK-35R-D and # AKFBBRK-35L-D...
  view full answer...
  
• Spindle Compatible With Trailer Idler Hub Assembly AKIHUB-440-2-1K
  The Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - L44643 Bearings - Pre-Greased # AKIHUB-440-2-1K won't fit your trailer spindle as it will be too long. The reason is, this hub is designed to work on BT8 spindles, which are longer than what you have. The only solution we can offer is to replace your short and older spindles with a new one that will work with the Trailer Idler Hub Assembly # AKIHUB-440-2-1K, which is the BT8 Spindle for 2,000 lb Trailer Axles # TRU59FR. I have...
  view full answer...
• Grease Used in CE Smith Pre-Greased Hub CE13110
  I reached out to CE Smith, who told me the Trailer Hub Assembly with Carrying Case for 2,500-lb Axles - 4 on 4 - Pre-Greased # CE13110 uses a marine grade grease similar to the LubriMatic Marine Trailer Wheel Bearing Grease # L54FR. At one point the grease was in fact red but they changed it to the greener in color grease, with the only difference being the color, as both are marine-grade. I have added a link below to a video review of this grease if you'd like to take a look.
  view full answer...
• Selecting Replacement Bearings for Boat Trailer with Lippert Axle
  I checked with Lippert for the part number you referenced, A252875, but there was no match on this. Still it is easy enough to determine which set of replacement bearings you'll need by simply pulling one hub/drum and checking the existing bearings for their part numbers. Usually bearings will have their part number stamped into their outer housing as shown in the lower-left portion of the linked photo. Once you have your inner and outer bearing numbers it is easy to use our search box...
  view full answer...
  
• Choosing Idler Hubs to Replace Rusted Brake Hub/Drums on Jet Ski Trailer
  Yes, we can help you select compatible idler hubs for your jet ski trailer. Replacement idler hubs (hubs without a brake drum) can be selected by first confirming the axle's weight rating; this should be indicated on a plate or sticker on the axle itself, or on the trailer's VIN sticker. You need to choose hubs that are properly rated for the weight load that will be on them. You also need to match your wheels' bolt pattern. Next you need to pull one of your existing hub/drum assemblies...
  view full answer...
• Is the LubriMatic Marine Trailer Bearing Grease Compatible with Starplex EP 2 Grease
  Yes, the LubriMatic Marine Trailer Bearing Grease, # L54FR, is compatible with the Starplex EP 2 grease that you currently have on your Karavan boat trailer. I have attached an article on lubricating grease that you may find helpful when searching for new bearing grease.
  view full answer...
• Recommend Grease That Is Compatible With Boat Trailer Bearings
  I recommend using the Calcium Sulfonate grease like the LubriMatic Marine Trailer Wheel Bearing Grease - 3 oz. Cartridge # L54FR. You're able to combine the calcium sulfonate grease and the anhydrous calcium grease together. You need to make sure your quantities and amounts are mixed correctly so it is not too thick. If the grease is too thick it will not operate under the same temperature changes and will not be as fluid to lubricate all the smaller parts of the bearing. If you have any...
  view full answer...
• Recommendations for Bearing Buddies and Grease on Dexter 7,000 lb Axle
  Bearing Buddy Bearing Protectors like # BB2717SS will not work with E-Z lube axles unless you remove the grease zerk fitting like you mentioned from the spindle. Once that grease zerk is removed, then the Bearing Buddy will work as intended using the spring loaded design and integrated grease zerk to keep the bearings well lubricated and maintained. When adding grease, you need to be careful not to mix styles of grease as they aren't compatible in most instances. So you will either want...
  view full answer...
• Recommended Compatible Hubs for Use with Timbren Off-Road Suspension System ASR35HDS02
  In order to use 6-on-5-1/2-inch bolt pattern hubs on a Timbren axle-less suspension system those hubs will have to use the same bearing set as the hubs intended for that system. In the Timbren system # ASR35HDS02, for example, which has 4-inches of lift and is rated for 3500-lbs and off-road tires, the bearing set is inner bearing # 25580 and outer bearing # 15123. We do offer idler hubs and hub/drums in the 6-on-5-1/2-inch bolt pattern that you can see by clicking on the link provided....
  view full answer...
• Can Sealed 4 Round LED Trailer Light # STL43RB Be Used Underwater in Saltwater Environment
  I spoke with my contact at Optronics and in order to use the Sealed, 4" Round LED Trailer Stop, Turn and Tail Light, # STL43RB, in the saltwater environment, you will want to use marine grease like part # L54FR on the Straight 3-Wire Pigtail Plug, # A45PB, and then seal around the plug with a silicone sealant like part # 0160297. This will help to prevent any water from getting into the light housing during the constant in and out of saltwater service that your boat gets.
  view full answer...
• Recommended Bearing Buddy and Bearing Kit for Malone MicroSport Trailer
  The Malone MicroSport Trailer # MPG460G does have the 1.98 inch inner diameter hub. I confirmed this with the manufacturer. To add bearing buddies, you simply need the # BB1980A for chrome or # BB1980A-SS for stainless steel. You will not need to replace the bearings to install these caps. You can simply use the LubriMatic Economy Size Mini Grease Gun # L30100 and add the marine trailer wheel bearing grease # L54FR that matches what the axle comes with. When installing these, you will...
  view full answer...
• Would LubriMatic Marine Trailer Wheel Bearing Grease # L54FR be Enough for 6 Hub Assemblies
  The LubriMatic Marine Trailer Wheel Bearing Grease # L54FR would easily be enough grease for your 6 hub assemblies plus some extra for the future. You are correct though. Pack the bearing by hand and then use the EZ lube fitting to fill it the rest of the way up. I attached a video to this page that covers bearing packing as well.
  view full answer...
• Replacement for Dexter 8-248 Hub on E-Z Lube Axle and Recommended Grease
  The replacements for a Dexter 8-248 hub on an E-Z lube axle are the Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles # 84545UC1-EZ or, since you mentioned wet environments, the Galvanized Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles # AKIHUB-545-35-G-EZ-K. Both of these hubs will work with your 15 inch wheels and they have a 5 on 4-1/2" bolt pattern. For grease in your harsh wet environments I highly recommend the LubriMatic Marine Trailer Wheel Bearing Grease...
  view full answer...
• How to Find Correct Replacement Bearings for 2003 Roadmaster Enclosed Utility Trailer
  It is a good idea to go through your trailer's hubs and bearings to make sure everything is in good shape before your cross-country trip. The easiest way to find the correct replacement bearings, races and seals is to use the part numbers from the original parts that are on the trailer now. Please refer to the linked photo that shows the typical location and appearance of these part numbers. We offer many popular combinations of bearings, races and seals as kits, but the individual parts...
  view full answer...
  
• Wet Shackle Bolts to Reduce Noise from Tandem Axle Travel Trailer Suspension
  If you think the cause for the noise on your 2015 Jayco Whitehawk 24RBS tandem-axle travel trailer is from the normal travel of the suspension components (leaf springs, equalizers and shackle straps), you might switch over to wet bolts. The squeaking noises from trailer suspension can be reduced by replacing standard shackle bolts with wet bolts. Wet bolts like # TRFA71063 and # 126B2 have a grease zerk fitting that allows you to maintain a layer of grease between the surfaces of those...
  view full answer...
• Idler Hub Assembly for 2,000 lb Axle With 13 Inch Wheels
  We do have a solution for you, although the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles # 34822545BX does require wheels be only 8" to 12". The reason for that is there is this hub does not have a large enough flange diameter in order to to provide the necessary side-to-side support for a larger 13" wheel, so it can become loose on the hub. Instead, the hub you need for your 13" wheel is the Dexter Trailer Idler Hub Assembly for 2,000-lb Axles # 8-258BTUC1. This uses the same...
  view full answer...

Do you have a question about this Lubricants Sealants Adhesive?