To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Straight-style, extra-wide step bars give your Dodge Ram Pickup a rugged look. Polished stainless steel, oval tubes have molded plastic endcaps to keep out moisture. Oversize, 5" wide step pads provide sure footing. Custom mounting kit included.
Features:
Specs:
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today, on our 2008 Dodge Ram Pickup, we'll be installing the Westin Premier Oval Tube Steps, 6 inch wide, part number 22-6030-1015. Note that the short bracket will go to the front, and the long, or taller bracket will be the rear attachment point. Now, to begin our install, we'll first need to remove the front and rear body mount bolts. Once we have them removed, we'll then move to the inside of the rocker panel, and uncover and expose the cutout hole covered up by the tape. Next, we'll go ahead and put the T-bolt inside the cutout hole of the rocker panel, and secure it with a plastic flat washer. Next, we'll take our forward bracket, flat washer, long bolt, and secure the bracket to the mount.
Now, once we install the hardware finger tight, we'll go ahead and run it down. However, we'll leave the bracket loose enough that it can be moved in or out as necessary.Next, we'll install the bracket support. The bracket support will go over the T-bolt in the rocker panel, and get secured with a flat washer, split lock washer, and then a nut. Once again, we'll install all of our hardware finger tight, until we have it all in place. And then we'll bolt it to the bracket using the bolt flat washer going through the bracket and support, then securing with a flat washer, split lock washer, and nut.
Once again, we'll install all of our hardware finger tight, until we have it all in place. Once we have the forward and rear brackets in place, we can then go ahead and install the four-studded t-fastener into the tube step. To do this, we'll take it . turn it side ways, feed it through the opening, and then pull it back up, so that the four studs are sticking down and out the bottom of the tube step. We'll need one for each bracket, so we'll have one at the front and back of our tube step.Once we have our fasteners in place, we'll then go ahead to prepare and set it on the bracket.
Then, we'll repeat the same process for our rear attachment point. Now, with our fasteners inside the tube step, we'll prepare to set it onto our brackets. Between the tube step and bracket will be a spacer. The spacer will line up with the studs coming out of the bottom of the tube step, and then line up with the bracket. We'll secure each fastener with a flat washer and nylon lock nut.
We'll do this for both front and rear brackets. Now, with all the hardware installed, we can go ahead and tighten it down. Next, we'll torque specifications, as indicated with . in the instructions. Now, with one tube step installed and secured, we'll go ahead and repeat the same process on the other side. And with both steps installed, we're now ready to hit the road. And that does it for the install the Westin Premier Oval Tube Step part number 22-6030-1015 on our 2008 Dodge Ram Pickup. .
Average Customer Rating: 5.0 out of 5 stars (7 Customer Reviews)
Straight-style, extra-wide step bars give your vehicle a rugged look. Polished stainless steel, oval tubes have molded plastic endcaps to keep out moisture. Oversize, 5" wide step pads provide sure footing. Custom mounting kit included.Boards look great and function well. Very happy with them. I replaced some rotted out boards that came with my truck. My particular vehicle is older so install was not as smooth as there is some corrosion, but that isn’t fault of the boards. I also found directions to be quite limited and it took me way longer than I expected to install. I figured it all eventually though and I still happy with my purchase. etrailer.com is a great company to work with. I recommend etrailer.com to everyone I can.
Our "new" Dodge 2500 4x4 is a bit taller than our previous 1500... So we decided to install a set of tube steps to make life a bit easier. The 6" oval tube polished stainless steel from Westin was selected both for their great looks, and for their life time warrantee. Installation was relatively easy, an hour for the first side and 15 minutes for the other side! My biggest worry was getting the four factory cab mount bolts out, but had no problem. They look great on the truck, and my wife is now able to easily get in and out without a step stool!
I ordered The 6” Westin side steps for our service truck and within 12hrs they were being shipped. I was impressed how I was informed of each step of process and delivery. The steps are very sturdy and look great. I would definitely recommend the steps as well as etrailer.com.
These running boards were easy to install once I had figured out the orientation of the brackets to the boards. I put them in to help my wife get in and out of the truck.
Super easy to install and have held up well
Great product! Fits and looks superb!
Do you have a question about this Nerf Bars - Running Board?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.