Arrives before Christmas 
Replaces the electric step, motor, and switch kit for your Kwikee 28 series RV steps. Motor extends and retracts the step when it receives the signal from the switch kit. Wiring pigtail hardwires to your RV's power.
Features:
Specs:
Note: This step assembly includes the steps, motor, and switch kit only. The steps will operate manually through the switch kit.
If you want the complete step assembly that allows the steps to automatically extend and retract with the RV door, you will need a control unit. The switch kit included with this assembly will still work, but if you want to be able to override the automatic retraction, so the steps stay out whether the door is open or closed, you will need a different switch kit. The complete assembly with steps, motor, control unit, and switch kit is available under part number LC3756271.
The included 4-way plug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.
Will Kwikee Electric Steps Work for You?
Electric steps are typically installed on RVs and some travel trailers. The electric steps from Kwikee install and fold up underneath the camper for simple storage. To ensure you choose the correct size for your application, there are a few measurements you will need to take.
The Kwikee electric steps attach to the underside of the camper chassis, directly beneath the doorway. To decide which size you'll need, locate the space available underneath your camper that lines up with the doorframe, and measure the width and depth. You will need a mounting space that is at least 31-1/2" wide and 11-3/8" deep.
If it turns out you have more or less space beneath your doorway, there are other step assemblies available with bracket sizes ranging from 24-3/4" wide to 37-1/4" wide. A full list of the available steps is below.
Outriggers - metal brackets that act as an extension (LC301704 - sold separately) - may be needed for installation depending on the model of your original stairs. These provide extra length if the old steps are longer or wider than the new.
Once you know where the mounting bracket will go and what size mounting bracket you need, that spot will be used as the "mounting point" to determine how many steps you will need.
How Many Steps Do You Need?
To decide on how many steps you'll need, measure from the mounting point to the ground. This is called the entry height. The entry height should roughly match the height of the steps when they're fully extended, plus 6" to 8" to account for the drop from the bottom step to the ground. This measurement will also tell you how many steps you need.
The chart below displays mounting bracket widths in the first column and entry height measurements in the second column. The third column shows the corresponding part numbers. Use the mounting bracket width and entry height measurements you took to determine which part number will fit your RV. Choose the bracket size that is closest to your measurements without going over.
This page's step assembly is in bold text.
| Mounting Bracket Width | Entry Height | Part Number (Complete Assembly) | Part Number (Replacement Assembly) |
|---|---|---|---|
| 24-3/4" | 15-5/8" - 17-5/8" | LC3747453 | LC3747452*, LC3747451** |
| 25" | 16-3/4" - 18-3/4" | LC3724742 | n/a |
| 25-1/2" | 27-7/8" - 29-7/8" | LC3658373 | LC369552*, LC365837* |
| 25-1/2" | 20-1/8" - 22-1/8" | LC372261 | LC3722615*, LC3722617**, LC3722616*** |
| 25-1/2" | 20-1/2" - 22-1/2" | n/a | LC3725791* |
| 25-1/2" | 12-1/8" - 14-1/8" | LC3723383 | LC372338** |
| 25-1/4" | 13" - 15" | LC3711363 | LC371136*, LC3711361** |
| 25-3/4" | 22-7/8" - 24-7/8" | n/a | LC372558* |
| 25-5/8" | 11-7/8" - 13-7/8" | LC3691461 | LC369146*, LC3691462** |
| 25-5/8" | 13" - 15" | n/a | LC3726041* |
| 25-7/8" | 23-1/4" - 25-1/4" | LC3726892 | LC3726891** |
| 26-5/16" | 27-1/4" - 29-1/4" | LC3694042 | n/a |
| 29-3/8" | 18" - 20" | LC3722661 | LC372266*, LC3722662** |
| 30-1/4" | 15-1/4" - 17-1/4" | n/a | LC372779* |
| 30-3/8" | 17-1/4" - 19-1/4" | n/a | LC427247* |
| 30-5/8" | 20-1/2" - 22-1/2" | n/a | LC375632* |
| 31-1/2" | 28-5/8" - 30-5/8" | n/a | LC375821* |
| 31-1/2" | 12-3/8" - 14-3/8" | LC3756271 | LC3756272** |
| 32-3/8" | 20-1/4" - 22-1/4" | LC3722862 | LC3722863** |
| 37-1/4" | 18" - 20" | n/a | LC3694112*, LC369411*** |
*Motor and control unit
**Motor and switch kit
***Motor only
How Do You Install the Steps?
To install the steps:
-Set aside steps before drilling
-Make sure bracket is backed up fully against the I-beam on the chassis
-Hardware not included
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey guys, this is Jake here with etrailer. Today, we're gonna go over some details and the measurements that you're gonna need to take if you're wanting to replace your fifth wheel or your travel trailer steps. If you're looking to replace your motor home or your RV steps, we're gonna have a separate video made just for that. Now, a couple of reasons why you might want to replace your steps. One of the biggest reasons is because people don't like these pull out steps because they're uncomfortable and makes for a not pleasant experience on the inside of the camper if they're folded out because they hover above the ground. When somebody steps on 'em, it rocks the whole camper.
So that might be a reason why you wanna upgrade from the pullout style steps to the fold out style which will fold up into the door of your camper. The nice part about the fold out is that they're going to be rested on the ground, so all the weight from the person walking into the camper is gonna be pushing on the ground and not pulling on the side of the camper. With that being said, a lot of people like this style because it's not gonna take up space on the inside of your door. So regardless of which kind you would like to go with, there's gonna be different measurements for each. There's gonna be a measurement for the pullout style if you wanna replace just the steps you have outside already.
And then there's gonna be different measurements for the fold up style, to be able to measure, you know, you're gonna have to measure from the ground to the inside and then side to side in the door. So, it's gonna be different because they're gonna be located in a different spot. Now, here we have a different set of pull down camper steps. The reason why I switched from my camper to these is because my camper, the bracket's actually welded in. If that's the case, you're just gonna have to cut it out.
But the reason we're showing you here is because these are bolted on and I'll be able to give you the proper measurements to replace 'em. So, first measurement you need to take is from this bracket, the bracket that's actually attached to your camper, not the step bracket, from the inside to the inside of these two brackets, which for us here is gonna be 27.5. And then what you need to do is you need to measure the depth of this bracket. So from this outer edge here to the trailer frame. Good for that.
We get about 13 and 3/8. And then the last measurement is from the ground. Now you wanna make sure you're on level ground and your camper is level from the ground to this bolt right here on the outside. So that. we're getting about 26 and 1/4. Now, if you're looking to upgrade to a set of fold-down steps that actually store inside of your camper, the two measurements that you need to take is from inside flange to inside flange, not the inside of the actual door frame, because it's gonna need to fit in between these flanges. So for us measure right up against there and we get about 24.5. You can see there. The other measurement we need to take is from the ground, again, being on level ground from the ground to the top inside of the threshold itself. So for us, it's going to be about 35. And the last thing that you need to do is you need to match up the measurements that you've taken, whether you're replacing your steps that came on your camper or you're replacing them and upgrading to the fold up type. You just need to match up those measurements to the measurements on our product page for the steps that you're looking for. Well, guys, hopefully this information was helpful in helping you to find the right information and the right measurements you need to replace your camper steps. If you have any questions, please leave 'em in comments below and we'll see you next time..
Average Customer Rating: 4.9 out of 5 stars (36 Customer Reviews)
Replaces the electric step, motor, and switch kit for your Kwikee 28 series RV steps. Motor extends and retracts the step when it receives the signal from the switch kit. Wiring pigtail hardwires to your RV's power.
Easy to install and has worked great ever since.
I hit a curb and damaged the RV step, I called etrailer and gave Pat my info and she put me on hold while she checked with Manufature for correct part #. She emailed me with timely progress of my order. Upon receiving my order I removed the damaged one and installed the replacement. It was correct replacement and only took I hour to complete and is working great. Thank you
Have had this step installed for a year now. Install went as predicted. A bit of a pain getting it aligned and as I recall, needing to drill a couple of new holes. (This install replaced the existing non-stock step on a class A MH) I used the new magnetic contact switch which was a vast improvement from the button that was in the jamb before. Step has worked flawlessly since, it's quiet, always opens (switch is very consistent) and tucks up under the face of the MH perfect. Love this purchase, install and operation.
Looks right have not installed yet. Received it early so thank you
I ordered this step to replace a 21 year old step on our 2001 Monaco Windsor as I was having problems with it. I received the replacement on time and installed it in 30 minutes, It was a direct plug and play. Also the same quality as the old one. hopefully get another 20 years from it. All my experiences in the past with E-trailer has been positive.
I have ordered dozens of items from Etrailer. They ALWAYS get it right. In spite of disappearing vendors, changes in versions, or totally new replacements; they are perfect in deciphering the correct part. Kudos to them!!!
The new step came the day before it was expected! It bolted up to the existing support structure and plugged in to the existing wiring...with the exception of the door (magnetic) switch. That was easy to replace as the existing wires had a connection behind the door frame. Two new crimps for that, then bolt up the new step and plug and play! Probably 2 hrs start to finish. But I was being careful.
Overall looked good after delivery. Used jack to help put up against frame to bolt on. The plug connection was short so was glad included with shipment was an extra extension wire with plug. Had to also replace magnet switch at door since without doing so the step closed when the RV door was opened and extended when the RV door was closed just the opposite ofd what it needed to be. The original magnet switch was not suited for this new unit. Called the manufacturer and they told me the included magnetic switch needed to be replaced for proper operation. Sure enough once I put the new magnetic switch in everything works perfect.
Box came damaged and opened. The step arm is bent as well on one side. Hole in the bottom of the box where the bent portion was sticking out.
Sad :(
Works perfectly just make sure you replace the door switch on older model or it will work backwards
As usual etrailer exceeded my expectations. The step arrived much sooner than expected. Very sturdy step and an exact replacement for our damaged one so it should go right in.
The Kwikee step was a direct replacement for a damaged step and was a perfect fit. ETRAILER kept me informed of delays and offered suitable replacements. I chose to wait on my original order and still received it in a very timely manner. I have been very pleased all products I have purchased from ETRAILER.
Love the step, it bolted and wired right up. Had it operating in less than an hour.
Replacement for a step that got in the way of a big rock. Once supports got bent back in shape, installation was straightforward. Electrical was a little different than factory setup, but step has additional function now. Works great.
The step was exactly what I needed. And the installation was easy. The only thing I would include would be both limit switched.
installed on 1999 Monaco Dynasty did have to drill mounting holes just a little to lineup.Works great, No problems at all. Finish seems to be holding up well. would highly recommend.
Excellent product recommendation by etrailer. Excellent installation.
This step is a big upgrade from the original steps. Much better mechanism and smoother operating than the original.
it was i was looking for.it shorter in high perfect.
I’m very satisfied, great communication. Always available!
These guys and gals know their products and deliver as promised. I have been buying from them for about three years now and I am very satisfied with the customer service I receive.
We really like it!
Couldn't be more happy with the product.
Everything is exactly what it should be thank you for your excellent service I got the package the following day which is even earlier than you originally mentioned great thank you
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.