Metal Low Profile Replacement Cover
(492 reviews)
Price: $33.01
In Stock
Metal Low Profile Replacement Cover
Item # BV0534-00
Retail:$93.59
Our Price: $33.01
You Save: 65%
In Stock
- All Info
- Reviews (492)
- Q & A (0)
- Videos (3)
- Photos
Ventline RV Vents and Fans - BV0534-00
- Roof Vent
- Replacement Lid
- 14W x 14L Inch
- Silver
- Ventline
- Continuous Hinge
Replaces the flat metal cover on Ventline Ventadome RV roof vents.
Features:
- Replaces the flat, low-profile, metal lid on Ventadome roof vents for motor homes and enclosed trailers.
- Works with Ventline Ventadome roof vent model V2110.
- Measures: 14-1/4" by 14-1/4"
- Mill finish
- Made in the USA
BV0534-00 Ventline Metal Low Profile Replacement Cover
Video of Metal Low Profile Replacement Cover
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Ventline Replacement Operator for Trailer Roof Vent Installation
Today on enclosed trailer we'll be installing the Ventline replacement operator with knob and screw for Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. We'll also be installing the replacement dome assembly for the Ventline Ventadome trailer roof vent. Part number Bv0534-00. Now you'll need to first take apart the interior portion of the vent. There's four screws that hold the outer trim piece on.
You want to be extra careful here, as the plastic becomes very brittle as it gets older. Next there's two screws, one on the front and back, that hold the screen in place. These are small Phillips head screws. With that done, we'll go ahead and set the screen down out of the way. Next, you'll remove the two screws that hold the operator arm in place. You'll then slide the operator arm out through the slot.
We'll then take the new operator arm, slide it back up into place, and put the two screws back in, holding it to the frame of the vent. Next, we're going to need to go up on the roof of the trailer. Now we're ready to install the new cover. Just slide it in from one side and as you're doing that you want to make sure that the actuator arm slides through the round portion and then up into the channel. Now, it makes it a little easier if you have someone down in the trailer to help guide this through, or to raise and lower the actuator arm if need be. Now, we'll go ahead and lower the lid all the way down where we can bend the tab over. You want to make sure that both sides are bent far enough that there's no chance they can slide back out of the track.
Next, we'll need to go down into the trailer where we'll be attaching the friction clip to the operator arm. That way it can't come off of the new lid. You want to make sure that the concave side of the clip bears against the dome bar. If you've attached the handle temporarily, you will need to unscrew it so we can put the screen back up into place. Once the screen's back up into place you can go ahead and put the handle back on. Finally, we'll put the trim ring of the piece of plastic that goes around the outer edge with the four screws.
With that, that's all there is to it, to replacing the Ventline replacement operator with knob and screw for the Ventline Ventadome trailer roof vent with metal dome. Part number BV0115-04. .
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Did not fit
- Arrived Damaged
Customer Reviews
Metal Low Profile Replacement Cover - BV0534-00
Average Customer Rating: 4.9 out of 5 stars (492 Customer Reviews)
Replaces the flat metal cover on Ventline Ventadome RV roof vents.by: Wendy05/30/2023
I waited several months before writing a review so that I could make sure this replacement cover didn't leak. It hasn't! It was really easy to install which I did myself. For reference, I'm a 53 year old woman. Our trailer is an enclosed aluminum trailer, and this cover fit perfectly.
by: James 09/09/2023
Cover was easy to replace and fits well. I either missed the recommendation that the seal may need to be replaced or there should be . Eitherw way I'm happy will be ordering a seal.
by: Jim H06/24/2016
We have replaced over a dozen cracked and UV damaged plastic roof vents on our cargo trailers with the Ventline metal vents and replacement metal covers from etrailer.com.
etrailer has always provided us with fast turnaround time on deliveries and excellent follow-up and their pricing is very competitive.
I recommend etrailer to anyone who needs trailer parts and accessories.
Jim H.
by: Rodney10/09/2022
My trailer has 4 roof vents, and they all disintegrated at the same time with two of them blowing off in a thunderstorm. I live in SW Arizona, so the sun does a ton of damage. I was looking for vent lid replacements that should hopefully last longer than the last ones, and took a chance on these metal ones. Although we had some issues with the ordering, the lids arrived in a few days, well packaged and in perfect shape. I had to wait until my son was available to install, as you need someone inside the unit and someone on the roof. These metal lids fit perfectly on my 2019 Shockwave (Forest River) vents, and should last quite a while I hope. Although these lids won't allow any light in, the old vents were black, so shouldn't be much of a difference.
by: Rhonda P. 06/01/2019
I ordered 3. I received them promptly, but the hinged area that you slide onto your camper was to loose and the cover came off when I opened it. So I had to use a pliers and crimp them smaller. Then one had rivets on the support bar where the other 2 did not so it won’t close all the way.
by: Bruce09/23/2016
I am very pleased with your service and received the Roof Vet Covers in a timly manner.
The covers fit just fine and look nice. See trailer picture attached.
by: Dave in NC10/22/2014
Much lower profile than the original plastic dome I shattered when rolling my trailer into the garage (DOH!).
The Installation video was helpful but, due to the obscure screws my trailer manufacturer used to install the vent, I had to work topside, above the screen, using an offset screwdriver.
The replacement dome arrived very quickly (which was good, 'cause rain was on the way).
by: Wes H08/22/2018
Ordered this metal vent lid to replace the deteriorating plastic lid on my 2017 Lark trailer and have no regrets. This lid is well built, fit perfectly and operates smoother than the plastic one because it flexes less. Followed the directions on the package and had the lid replaced in 10 minutes or so. It was an easy swap and probly the best investment I could have made for the integrity of my trailer. No more worrying about hail busting that cheap plastic lid. I will definitely be ordering my new trailer with this lid installed. I highly recommend replacing those cheap plastic lids with this one.
by: Leanna09/15/2019
Came exactly as advertised. Installed quickly. No pictures of before, the plastic completely fell apart in removing. I opted to paint it white with Rustoleum, and it works great. Wish I had known this was available the last time we replaced it. Should never have to replace this on this unit again. Will definitely remember this for ANY future applications.
Comments
It’s been installed a year now and still looks and works great. Best replacement for the top vent on the market. I am not sending another pic, because it still looks as good a year later.
Leanna - 09/16/2020by: Rodrigo01/28/2019
Thanks
El producto tal como se indicaba llegó perfecto y calzó muy bien en mi camper. De muy fácil Instalacion, no más de una hora. Gracias
(The product as indicated was perfect and fit very well in my camper.
Very easy installation, no more than an hour.
Thank you)
by: K.G.05/10/2019
The plastic vent cover on my 2018 trailer, only a year old started crumbling and disintegrating, received this metal cover from etrailer.com and was very satisfied, shipping was quick and installation was easy, probably the last vent cover I will ever need for this trailer.
Thank you etrailer.com
by: Erin B09/28/2022
We love our new metal covers for our camper! We replaced our old and cracked plastic ones; they were no match for the sun! These metal ones will last and the high temps we get in NorCal won’t affect them! We love to hear the rain fall on them; reminds me of my metal roof on my house.
by: Murray12/23/2019
Shipped promptly. Easy installation. Seems to be a great lid
Comments
Its been solid! No leaks,cracks or issues. Very happy with my purchase.
Murray - 12/25/2020by: Valeriy01/04/2023
Worked well after painting it. Wish it was galvanized.
by: Thomas05/05/2023
Looks like it will be a perfect fit, won't have to worry about the plastic rotting out anymore since this one is metal quality looks good, fast shipping thank you
by: Anthony C.08/11/2014
Fits like a glove, way better than the plastic dome that was on it and ended up cracking and blowing away in a wind storm.
by: Jef lindenmayer08/28/2019
I purchased two flat metal vent covers for my 5th wheel as it sets outside in the extreme elements of the Arizona desert. Prior to me finding the metal vent covers at etrailer I would have to replace the plastic vents every year. Glad I found these vent covers. Get a couple for yourself and never worry about having to replace them again.
Jef Lindenmayer
Comments
These vent covers have eliminated the need for annual replacement. Save yourself some time from crawling on top of your RV and keep the money in your pocket. Buy the metal vent covers.
Jef l - 08/29/2020by: Todd04/01/2019
Perfect fit, easy install and most of all this item should not crack after 1 year of use like the plastic models and leak while on the road in a rainstorm. The only drawback is less natural light in the trailer but less light is better than ruined cargo due to water damage. This item should last the life of the trailer.
etrailer.com always gets your item to you promptly with great tracking options.
Comments
One year later and still working perfectly!
Todd R - 04/08/2020by: Christy 01/29/2023
Has held up great! And fit perfectly so no more stressing over the sun or any weather messing it up or cracking it! Thank u.
by: Thomas02/21/2018
Good vents, fit right and only one desire is that they were aluminum instead of galvanized metal. Eventually will rust so am giving a protective coating to further retard rust. Replaces my old 5th wheel vent covers; second or third time, now
will not have to worry about having to replace again as with the plastic ones.
Comments
GREAT! Only problem was too low for bathroom vent but a little hammer work took care of that. Last one I will have to do.
Esther T - 02/24/2019by: Daniel 06/26/2020
I purchased the metal dome replacement for my ventline trailer roof vent because the original completely crumble to pieces after two years. Like always Etrailer shipped extremely fast, parts were packaged superb, installation was extremely easy and well documented with lots of instructions and the fit and finish was by far better than the originals. etrailer is the best!!
Comments
The vent covers are the best I have ever owned! I would recommend them over any other product!
Daniel - 06/27/2021by: Shawn 08/22/2022
Sturdy replacement unit for the money. Not as fancy as the plastic domes but I think it will hold up to the weather much better and longer.
by: Doug L.10/30/2012
Just what the doctor ordered!! Needed to replace the two old cracked plastic vent covers on my 1982 vintage Alaskan camper with more durable lower profile alternatives to better fascilitate the use of the boat/canoe rack and to stand up better to heavy snow
loads. The BV0534-00 worked equally well on both the original DTS
unit and the newer Elixir replacement unit and will undoubtedly hold up to the elements much better.
Comments
Its now been over a year now since I installed the two Ventline BV0534-00 replacement covers on my old Alaskan camper and they are holding up very well and performing as good as new in spite of being continually exposed to the Ozark elements and excessive humidity.I just wish I had installed them years ago and avoided the expense and hassle of having to replace several inferior plastic covers over the years.Quality speaks for itself.
Doug L - 04/30/2014by: Jerry 05/07/2020
These metal vent covers were purchased to replace plastic covers on motorhome.
Easy to install. Did have to hammer dimple in one to clear vent fan motor in bath.
metal covers are lower profile than plastic. Have not had any condensation on inside of covers which was a problem with plastic in high humidity.
Comments
working fine, no problems
Jerry - 05/30/2021by: Jonathan04/26/2022
Perfect replacement for my cargo trailer. UV light disintegrated plastic dome and this one fits perfect in it's place. Took less than 5 minutes to install.
25
492
Show More Reviews
See what our Experts say about this Ventline RV Vents and Fans
- Metal Replacement Cover for RV Bathroom Roof VentThe only metal roof vent cover we offer is part # BV0534-00 which is meant to fit on a 14 x 14 inch roof vent with a continuous hinge. If this fits the description of your existing vent, the # BV0534-00 would work well for you.
view full answer... - Replacement Roof Vent Cover for Trailer Vent with Continuous HingeIt looks like the # BV0534-00 would work for you since you said that your roof vent has the same style of hinge that this cover has. When picking out a replacement roof vent cover the most important factor is the hinge style. Since yours has the continuous hinge then the # BV0534-00 would be the correct one to use. I attached an install video for you to check out as well.
view full answer...
- How to Find Which Replacement Vent Lid Replaces Cracked Vent Lid on 1987 Lynx Prowler CamperWhen measuring for a replacement vent lid, you will want the outside dimension of the housing that extends through the trailer roof. This dimension is typically 14 by 14 inches. Closely examine the remaining portion of the vent, looking for a manufacturer name or model number. If you cannot find that information, you can examine the replacement lids we offer (see link) and match them up by the dimension of the housing and the style of hinge. Each replacement lid will have a detailed photo...
view full answer...
- Metal Replacement Cover for RV Roof VentThe only metal roof vent cover we offer is Replacement Dome Assembly # BV0534-00 which has a continuous hinge and fits a 14 x 14 inch roof vent. Since the hole in your existing vent is 14 x 14, you will want to check if your previous vent cover had a continuous hinge. If so, part # BV0534-00 should work well for you.
view full answer... - What Type of Metal is the Replacement Dome Assembly BV0534-00The Replacement Dome Assembly # BV0534-00 that you referenced is made of galvanized steel which means it has a zinc coating on the steel that prevents it from corroding. I attached an install video for you to check out as well.
view full answer... - Could Aluminum Trailer Horse Trailer Use Ventline Vent part # BV0534-00If the roof vent on your horse trailer is the standard size of 14 inch by 14 inch then yes the Ventline Roof Vent part # BV0534-00 is a fit and would work well. If the vent you are replacing happens to be smaller you could always enlarge the hole to allow this one to fit as well. I attached an install video for you to check out as well.
view full answer... - Will White Replacement Vent Cover Last Longer Than Smoke Colored Cover For Pre-1995 Elixir Roof VentWe offer one metal replacement vent cover. It is part # BV0534-00 but it is designed for a 14-1/4 x 14-1/4 inch vent. The 61635 and 61634 are designed for a 14 x 14-inch vent. The discontinued part 61635 is made of plastic so I don't think there will be a lot of difference in the length of time either replacement lid will last.
view full answer... - Can a Metal Replacement Vent Cover be Used to Replace a Plastic Vent CoverReplacement vent covers are very specific in terms of what vents they will fit. Metal cover # BV0534-00 is designed to fit Ventline Ventadome roof vent model V2110. If your vent originally had a plastic cover chances are this metal one will not fit. I have included a link to the vent covers we carry. If you are not sure of the model number you will need to look at the hinge style on the existing cover and compare it to the hinges pictured on the product pages of the covers.
view full answer... - Can Older Ventline Roof Vent Lid be Replaced with Metal LidYou can replace your plastic vent cover # BV0554-01 with the metal lid part # BV0534-00 that you referenced and you'd be set.
view full answer... - Replacement Metal Dome Cover for Vent Assembly on 2003 United TrailerBased on my research, the Ventmate model cover you are currently using is designed to fit the same 14 x 14 inch opening as the Ventline Replacement Dome # BV0534-00 that you referenced, and just as important, features the same continuous hinge style. With this in mind, this Ventline metal cover should work perfectly as a replacement and will provide a more durable unit. I have attached a couple of short video demonstrations on this cover that you can also check out to get a closer look...
view full answer... - Can Metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vents be PaintedReplacement Dome Assembly # BV0534-00 doesn't have to be painted but you could paint it if you want to. There are special requirements for painting galvanized metal though. The first thing you will need to do is clean the galvanized parts with water-based cleaner/degreaser to remove any of the oily film on the parts from the galvanization process. Once clean you will need to use a water-based primer. Do not use a petroleum-based primer because the oil can interact with the zinc on the...
view full answer... - Replacement Metal Roof Vent Cover for Spartan Cargo TrailerI don't have any way of knowing what the screw size that's being used on your current trailer, but I can tell you that the Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent - Flat, Mill Finish Metal # BV0534-00 will work on your vent. The 14-1/4" x 14-1/4" is the actual size of the vent opening in the trailer, but the vents themselves are 14" x 14". When measurements are referred to, everything that mentions one of those two sizes is going to be the same, so the parts are...
view full answer... - How To Remove Dome On Ventline Trailer Roof VentThe removal of a trailer roof vent dome will vary by model but most use a fairly standard hinge design which requires releasing the lift arm from the center and then sliding the dome to either side once partially open for removal. The hinges can become rusted so it may require some penetrating oil and elbow grease. They don't all remove the same way but this method is most common and you can send a photo if you feels yours is different. If you need a new replacement dome I have attached...
view full answer... - Replacement Metal Roof Vent For A 14" x 14" VentIf you have a cover like the part number 4140155 that you have provided, that is a 14" x 14" so this low profile metal cover # BV0534-00 is 14-1/4" by 14-1/4". The extra 1/4" is just from the 1/8" lips on each side.
view full answer... - Will Metal Lid Replace Plastic Roof Vent Lid with Continous Metal HingeYes, if you have the same continous hinge on your roof vent as the metal lid part # BV0534-00 this lid will work well as a replacement. I attached an install video for this for you to check out as well.
view full answer... - Can Plastic Trailer Roof Vent Lid with Continuous Hinge Be Replaced with Metal LidGenerally speaking, if the hinge is the same then you can use pretty much any replacement lid as the sizes are all standard. Therefore, the metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent part # BV0534-00 should work for you since it uses a continuous hinge. That said, there can be issues with the arm when switching from a dome to a wedge shape or vice versa so that something to keep in mind
view full answer...
- How to Pick Out Replacement Vent Cover Recommendation for a 2004 Fleetwood WildernessThere are a few things to look at when looking for the correct replacement vent cover for your trailer. The first item that will help is knowing the manufacturer of the vent on the trailer, such as Elixir, Jensen, Ventline etc. The next thing that you will want to consider is the size of the vent itself. The Vent Cover, # BV0534-00, that you referenced is designed to fit plastic vent frames that are 14 inches by 14 inches. The actual outside to outside dimensions of this vent cover are...
view full answer... - Are the Ventline Vent Covers # BV0554-03 and # BV0534-00 InterchangeableYes, the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents # BV0554-03 uses the same hinge style as the # BV0534-00 that you also referenced so the two would be interchangeable. We actually had a customer send us in picture of how they used the # BV0554-03 to replace a damaged # BV0534-00 that I attached.
view full answer...
- Roof Vent Operator Recommendation for a Metal Lid Roof Vent on 1989 Casita TrailerSounds like you need the Replacement Operator w/ Knob # BV0115-04. This operator is designed to fit the roof vents with a metal lid and crank handle in the center of the vent like what you have. Check out the install video I attached so that you can compare your vent to what this product fits, and to see how it will install.
view full answer... - Can a Metal Vent Cover Replace the Plastic Vent Cover for a Ventline Trailer Roof VentYes, the metal replacement dome assembly # BV0534-00 you referenced will work as a replacement for the plastic vent cover # BV0554-01. The replacement cover # BV0534-00 measures 14-1/4 x 14-1/4 inches and is a galvanized metal to combat corrosion. I included a couple videos that you can take a look at too.
view full answer... - Replacement Roof Vent Lid for 2015 Diamond Cargo Car Hauler TrailerDiamond Cargo's website does not provide any details about the roof vents installed in their car hauler trailers but since most trailer roof vents are the square 14 x 14 size chances are good that is what you have. We offer all types of roof vent replacement lids. If you can find a brand and/or part number anywhere on the vent that will help too. You'll want to check the hinge type used on your vent. There are three basic types and all are shown on the photo I linked for you. Once you...
view full answer...
- Available Trailer Roof Vent Replacement Lids with Continuous Type HingeWe offer replacement lids, complete vents and also protective vent covers for 14 x 14-inch trailer roof vents. We do not offer anything in a 13 x 14-inch size so I will presume your vent is a 14 x 14. You can use the linked page to click on Replacement Lids at the top of the page; then just click continuous hinge to see products like Ventline white Rounded Dome Lid # BV0554-01 or metal lid # BV0534-00. If you can find a brand name and/or part number on your vent that will help to narrow...
view full answer... - How to Select Replacement Lid for Trailer Roof VentReplacement roof vent lids come in one of three hinge types and this you will want to match to yours as you select replacements. Please refer to the linked photo that shows the three hinge types, 3-point, 4-point and continuous. You can then use the linked page for roof vent lids to select the hinge type and preferred color. For example, for a flat metal vent lid with a continuous hinge you can use part # BV0534-00.
view full answer...
- How to Pick Out Replacement Vent Cover for 2009 American HaulerIf your roof vent had a plastic cover on it then the correct vent cover would be the part # BV0554-03. If instead you had a flat metal cover you would need the part # BV0534-00. Both of these have continuous hinges.
view full answer...
Do you have a question about this RV Vents and Fan?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Video Edited:
Zack K
Video Edited:
Chris R
Written by:
Raymond P
Installed by:
Cole B
Updated by:
Mary K
Updated by:
Manda E
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-636-245-0062
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.