In-stock alternatives that can ship today
Replace the vent cover on your Elixir trailer roof vent (made after 1995) or your Ventline trailer roof vent (V2094 - made before 2008) with this equivalent part. Fits 14-1/4" x 14-1/4" openings.
Features:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today in this old enclosed trailer we're going to repair the roof vent. What we're going to do is put a new cover on the top of the vent and on the inside we're going to install a new screen. A new screen for the inside is part number BVC0573-31 and our roof vent cover is going to be part number BV0554-01. First, we'll go ahead and take the trim ring off the interior here. Now there's a screw here and here we have to remove. We also have to remove the handle too.
Now this is the condition of the roof vent right now. The dome is completely gone and all that's left is a hinge and the brace in the middle. What we'll do is crank the brace up a little bit to make it easier to remove and we'll remove what's left of the hinge. On the bottom of the hinge is some tin that we just peel off out of the way and you should be able slide off to the other side. We'll also remove the trim ring and the screen.
We'll need that out of the way to work with it. Let's go ahead and bring this up. We'll go ahead and put our new vent dome in place. We just slide it on. Now we'll take our tab and just bend it down so it cant slide out.
We'll do that in both sides. Now, to put our crank mechanism back into track, we'll just go ahead and loosen it up, put the roller back in here and then bolt it back in place. Now, we can go ahead and put our screen in place. Now this is our old vent and this is the new vent we're going to replace it with. Dimension wise, its an identical fit.
However, the only difference is the hole for the crank is located in a different stop. The older screens or older vents are getting harder and harder to find. By using this new vent, we'll only need to do one modification. We'll place one over the top of each other, square it up and we'll use a 1/2-inch drill bit to mark our hole. We're going to give you a measurement from this mark to the edge right here. Now that looks like 3-3/4 inches. We'll put a block under it then we'll drill out a hole. We'll start smaller and work our way up so that way we have a nice even finish when we're done. Now, for our original hole here when we have everything installed, we'll just use some silicon sealant to fill up the hole. We're going to reinstall the trim. We'll go ahead and put our handle back into place then we'll take a few seconds to seal up that hole. Also, if you can get a hold of a plastic plug, you'd use that as well on here too. We'll go ahead and operate it. With that, that'll finish it for our roof vent repair on this old trailer.
Average Customer Rating: 4.9 out of 5 stars (2444 Customer Reviews)
Replace the vent cover on your Elixir trailer roof vent (made after 1995) or your Ventline trailer roof vent (V2094 - made before 2008) with this equivalent part. Fits 14-1/4" x 14-1/4" openings.
These pictures are of the replacement of my vent covers on a 1975 Star Craft Camper. The ones I ordered from you were slightly bigger, 14.5 inches, than the standard 14 in replacements and were a perfect fit. They installed easily once I removed years of caulking and sealant from the hinged slide rail. It has been a year since I replaced the covers and they are holding up just fine. Recommend any do it your selfers carefully measure the existing covers to make sure they will fit properly.
Robert - 05/08/2020These were the perfect replacement vent covers (2) for my camper. Very easy to install. I would use them again. One of my crank mechanisms is missing a metal spring clip so it doesn't work as smoothly, but I highly recommend these covers.
Robert E - 09/08/2021I think the product will be ok, havent installed them yet but 2 of the 4 i ordered may give me problem due to packing. They seem warped and both are flat on top where they should be domed.
Perfect replacement for my old deteriorated vent cover. Easy to install, direct fit.
Perfect replacement for 20 year old covers! They fit great, are easy to install (you'll need to work from inside and on top the camper), seem to be sturdy yet forgiving enough to take an errant tree branch or light hail, and let a lot of light inside. The domes are slightly higher profile than the OEM, but it provides a quieter angle for raindrops (and "glancing blows" angle for small hail - which cracked the old ones). I doubt I'll need to, but I would buy them again - especially from etrailer.com.
Gabriel - 06/18/2020Shipped RV roof vent in a very timely manner. Roof vent was very easily installed. My old roof vent was becoming brittle and hard to clean. This replacement fulfilled my need. Thank you for excellent customer service.
Michael R - 07/25/2021The rv roof vent covers fit absolutely perfect as a consumer it’s really appreciated when the product that is ordered and recommended by the etrailer product information dept fits and is adaptable perfectly . Thankyou so very much etrailer .Very pleased
Hello...yes, we did receive our package. When my husband opened the box, he discovered several of the roof vents had slight dents in the top, due to the fact they were taller than the box would allow for closing, so showed signs of being pushed down from the top so the box would close. But he managed to push the dents out without a problem.
This was so easy to install from the instructions provided I didn't even need to use my degree in Engineering. Now I need to recoat the roof
Vent cover arrived ahead of promised delivery time in perfect shape. Second time I have ordered from etrailer.com. Site is easy to navigate and place order. When product arrived, instructions easy to follow. Now I am ready for the rain!
Was a simple replacement job. Hardest part was locating the proper bit that fits the screws holding inside flange.Replacement cover arrived within days of placing the order.
I got my item in the mail less than a week after I ordered. I have a 2004 Pace cargo trailer. The original dome fell to pieces from age and sun exposure. I found etrailer and found the dome item BV0554-01. Installed it in about 15 minutes. Looks and works great.
Kenneth M - 09/10/2019Great price and have easily installed both vent covers. Instructions were very good and the covers are an exact replacement. Thank you.
Jim H - 07/31/2021I have an enclosed trailer that had a deteriorated roof vent. I wasn't sure which vent would fit my trailer because two different ones were available. I checked out several websites and etrailer.com had the best detailed information, pictures and how to DIY videos. This made it very easy for me to order the correct vent and install it with ease. It was also very competitively priced. I selected the cheapest shipping and was amazed that it only took a few days. Whenever I need anything for my trailers, I will go to trailer.com first!
This was just the replacement part I needed and it arrived in 1 day. The video help us take the old dome off and install the new one. Thanks for great service.
Paula - 09/06/2021Arrived on time and was a perfect fit for my 2005 Lance camper. Easy to install with detailed but easy to follow instructions. Very satisfied and best price I could find!
The new roof vents arrived in great condition and were the right size (always a good start). I watched a quick video on YouTube and had both vents replaced in less than one half hour! There are 6 different hinge types so make sure you get it right. I couldn't say enough good things about etrailer, they do Everything Right from order options, pricing, product education/knowledge and installation videos!!! Thank You etrailer!
Louie - 11/06/2020Install was pretty easy. Think followed something online.. One year later it still looks new. Thanks.
Perfect fit for my 2006 Atlas utility trailer. Easy installation, and virtually identical to the original vent. I had originally ordered part # BBC0530-01. etrailer notified me that the part was back-ordered from the factory, and suggested this unit instead. Worked like a charm and saved me $35! Thanks!
This shank works perfectly with my 2019 Chevy Tahoe with tow package and 2017 Forest River 2360 Trailer with a Pro Series weight distribution hitch. On the bottom adjustment holes it lines up at the same height as the trailer ball when level. A very heavy duty shank.
The replacement roof vent was perfect fit. I replaced old cracked vents that were leaking. works great.
very easy to install. I liked it nice and bright
Rose - 09/28/2021I ordered this cover to replace an old vent cover on my motorhome. This one was marketed as an exact replacement for the original manufacturer's part. The cover arrived packed cleanly and contained installation instructions. I installed the new cover and it fits perfectly!
Thank you. A 1 hour fix (2 covers) that I put off for 8 years. It's easy to do fix your vent covers.
The plastic only lasted 8 months At first I thought the wind caught it and ripped it off. But then the other vent that is exactly the same brand and age also fell apart. The plastic became very brittle. I’m very disappointed, I ended up buying a metal one because the plastic ones obviously don’t hold up.
Do you have a question about this RV Vents and Fan?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.