Lippert RV and Camper Steps
- LC432687
- 3 Steps
- Pull-Out Step
- Towable Camper
- 24 Inch Wide Step
- Lippert
- 27-1/2 Inch Wide
- No Ground Contact
- 7 Inch Drop/Rise
- Steel
This 8-1/4" deep, triple pull-out RV step opens and closes with just 1 hand. Anti-skid tread tape and water collection channels on step surface provide safe entry and exit. Bolts or welds onto your RV frame. Rust-resistant black powder coat.
Features:
- Manually operated RV steps make it easy to get into and out of your motor home
- Simply pull steps out for use and position back in place for travel
- Non-skid and slip-resistant step design
- Tread tape provides sure footing
- Water channels and drain holes help to keep rain from pooling
- Grab handle eases use and keeps hands clear of moving parts
- Black powder coated steel is sturdy and rust resistant
- Easy bolt-on or weld-on installation
- Mounts to RV frame in same manner as original step
Specs:
- Entry height: 24-1/2" - 27-1/2"
- Step dimensions: 25-3/4" wide x 8-3/4" deep
- Mounting bracket dimensions: 27-1/2" wide x 14" tall x 12" deep
- Drop/Rise: 7"
- Weight capacity: 300 lbs
- 1-Year warranty
![Lippert 687 Step Dims]()
![Lippert 687 step dims 2]()
![Lippert 687 Step dims 3]()
Will Lippert Pull-Out Steps Work for You?
Pull-out steps are typically installed on travel trailers. The pull-out steps from Lippert are easy to install and fold up underneath the camper for simple storage. To ensure you choose the correct size for your application, there are a few measurements you will need to take.
![Lippert Manual Mounting]()
The Lippert pull-out steps attach the underside of the camper chassis, directly beneath the doorway. To decide which size you'll need, locate the space available underneath your camper that lines up with the door frame, and measure the width and depth. You will need a mounting space that is at least 27-1/2" wide and 12" deep.
If it turns out you have more or less space beneath your doorway, there are other step assemblies available with bracket sizes ranging from 25-1/2" wide to 28" wide. A full list of the available steps is below.
![RV Steps Outriggers]()
Outriggers - metal brackets that act as an extension (LC301704 - sold separately) - may be needed for installation depending on the model of your original stairs. These provide extra length if the old steps are longer or wider than the new.
Once you know where the mounting bracket will go and what size mounting bracket you need, that spot will be used as the "mounting point" to determine how many steps you will need.
How Many Steps Do You Need?
![Lippert Manual Entry Height]()
To determine how many steps you'll need, measure from the mounting point to the ground. This is called the entry height. The entry height should roughly match the height of the steps when they're fully extended, plus 6" to 9" to account for the drop from the bottom step to the ground. This measurement will also tell you how many steps you need.
The chart below displays entry height measurements in the first column. If you determined you need a 25-1/2" mounting bracket, the step part numbers with that width are in the second column. If you determined you need a 25-3/4" mounting bracket, the step part numbers with that width are in the third column. The steps for 27-1/2" mounting bracket widths are in the fourth column, and the steps for 28" mounting bracket widths are in the fifth column. Choose the bracket size that is closest to your measurements without going over.
This page's step assembly is in bold text.
Entry Height | 25-1/2" Mounting Bracket Width | 25-3/4" Mounting Bracket Width | 27-1/2" Mounting Bracket Width | 28" Mounting Bracket Width |
---|
14-1/4" - 17-1/4" | Not available | LC432678 | Not available | Not available |
21-1/2" - 24-1/2" | LC432682 | Not available | Not available | Not available |
24-1/2" - 27-1/2" | Not available | Not available | LC432687 | Not available |
31" - 34" | Not available | Not available | LC432696, LC432690 | Not available |
36-3/4" - 39-3/4" | Not available | Not available | Not available | LC432698 |
How Do You Install the Steps?
To install the steps:
- Make sure the camper is level on flat ground
- Lift the steps into the mounting space and prop into place
- If needed, mark the mounting holes on the camper and drill
-Set aside steps before drilling
- If needed, install the outriggers
- Align step mounting holes and secure in place with bolts and flange lock nuts
-Make sure the bracket is backed up fully against the I-beam on the chassis
-Hardware not included
- Tighten hardware until snug
- Make sure assembly is sitting square and level
- Torque the hardware to 20 ft-lbs
432687 Lippert Components (LCI) Triple Radius Entry Step
Similar to Hickory Springs 953240RFXWC3, 95324EXTALC1, and 953240RFALC1
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.