Arrives before Christmas To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Aerodynamic, aluminum crossbars let you build an aftermarket roof rack for your vehicle. Full-length bars provide plenty of space for carriers and accessories. Vortex strips in C-channels reduce wind noise. Theft-deterring plastic locks included.
Features:
Rhino-Rack Vortex Aero Crossbars - Silver - 59" Long - Qty 2:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
How's it going everybody, it's Ethan here at etrailer. Today we're gonna be taking a look at and showing you how to install the Rhino-Rack Vortex Aero Roof Rack System on our 2021 Ford F-150. So with the F-150, obviously we have a good amount of bed space, but if you wanna get something longer or larger up there and maybe couple this with like a ladder rack to give some longer loads like a ladder or a lumber or on the sports and rec side, maybe you have a larger kayak you wanna get where you need it to go, a roof rack system like this one is gonna be a great solution for you. So let's take a closer look. The roof rack is going to have a weight capacity of 165 pounds. It's going to fit on our roof with the fit kit that we'll show you in the installed portion.
But 165 is gonna be a pretty solid or pretty common number that you see with roof racks like this, which is gonna be fine for most of the things you wanna get up there. You just wanna double check and make sure that your roof weight rating is in that same ballpark. Make sure you know what each of those are and go by the lowest ready component just to be safe. The crossbars we have on our system right now are gonna be 59", which is a solid length. We stay pretty much well within the width of our vehicle overall.
They're going to be elliptical so they taper on both ends to cut down on some of that wind noise and drag. But anytime you put something up on the roof, you're gonna deal with that. Luckily, we also do have a vortex strip on the top which is how the bars get their name. So that's going to help again cut down on some of that wind noise, otherwise we just have that open channel up here. Speaking of that channel though, that's gonna be great for your T-track accessories.
If you have those, you can slide those in. But with the strip you are going to have to trim it up if you wanna leave this strip in with those accessories on. So it's not a horrible idea to just grab another strip if you want to, in the event that you do end up doing some trimming. On our end cap here, we do have a plastic lock which we can use to unlock or lock our end cap but you can upgrade those to metal if you'd like. On the underside, you do have the option to use a measurement strip that you are gonna trim up and put wherever your towers are not.
In our case, this is just for demonstration and we'll talk a little bit more about that in the install portion as well, but that'll cut down on that whistling noise underneath as well. And using the provided key, we can take our end cap off and just show you how that works. So it's just a metal lock core there that will expose our fit kit hardware. So as long as our end cap is on and it's also locked up, no one is going to be able to access your fit kit hardware and remove the rack from your roof. From here I'm just gonna get a quick measurement to give you an idea of how much height you're going to be adding to your roof with the system. So from here in the middle, you're going to be looking at adding about 4-1/4" from the highest point. So if you're thinking about storing this in your garage, especially if you have something on there, add about 4-1/4" to whatever that's gonna be to find out whether or not it will fit in your garage or if you'll go anywhere where there might be some clearance issues. The roof rack system is gonna be made out of an anodized aluminum so it's gonna be really lightweight, easy to work with, but also very durable and rustproof at that point. It's got a nice matte black finish so it looks good. I think it fits the aesthetic of our F-150 really well. Overall, the install portion isn't too terribly difficult. It can be a little bit tricky, but you just need to be patient. Use the measurements that the instructions give you and make sure that you know where everything is gonna go. But if you need a little bit of help with that process, we'll walk you through it right now. To get started, the first thing we'd like to do is to slay everything out so that we know where and what it is. So we have our crossbars, we have towers, our fit kit, the clamps, and the hardware. We've got the pads and the bases for our towers. We have the tools and I would recommend picking up some kind of fabric tape measure as well as a regular tape measure. And then we have this measurement strip that comes included that we'll have to trim up according to our needs and definitely keep the instructions close by 'cause we will have to reference those often. But we'll begin by removing the end caps on our crossbars. We are going to use this plastic key to fit into the end cap. Just turn it and pull it out as long as we have it rotated fully, and we need to remove that in order to get our towers on. So we're going to line up this metal plate here with the underside, with the channel underneath our crossbars and just slide those on. And now is when you're gonna use that measurement strip. So for our case, ours has already been trimmed up so we can't use it effectively but you're gonna basically line it up with your tower, find the measurement on your instructions. In our case, we're looking for 169, so I'll get that roughly to where it needs to be. In your case, you could actually use the full measurement strip and trim it up if you need to. We repeated that process on the other side. We just slid our tower under this channel here and line it up according to the measurement, removed our end caps and now we just need to replace those real quick. Again, just put 'em on and tighten 'em down with the key. From here, since we're doing our front crossbar, just be sure to reference the instructions but we're going to attach one of our base pads to the rest of the base, and we wanna make sure you can see this arrow on here. We wanna make sure that ends up facing forward, so in our case, we're going to get these on and then we'll line it up with the tower. With the pad connected to the base, you can see where these openings are, and where they'll fit on our towers. So from here, again, we just wanna make sure that that arrow is facing forward, and we can snap this on into place. And then we're gonna repeat this process again on the other side. Once our towers are roughly in place, we're going to get a measurement. In your case, you could use the measurement strip. In our case, we would've to trim that up, and this is just for demonstration, so I'm gonna use our fabric tape measure to find that 169 millimeter mark in our case. And now I'm going to use the Allen key provided to tighten this down. As we tighten down, something important to note is that this tool does have a built-in torque spec, so just the way it's designed. Once we start turning, as soon as we see that line straightened out, that's about as tight as we want to go. Once we have our towers all set up, our measurements where we need 'em to be and both bases in place, now we can place our crossbars roughly on our roof, whereabout we think they're going to go. Just a matter of getting them roughly in place for now. And then we're gonna come back and get the measurement to make sure that they're in the right place. From here, again, since this is the front crossbar, I'm going to be using the measurement A in our case, which is 280 millimeters or 28 centimeters from the center of our door jam to the center of the tower. So in our case, I need to slide forward quite a bit. It's gonna be kind of hard to tell for now until I move the other one forward as well. So I'm gonna go to the other side and get that measurement now. Once we have everything in place and all our measurements are good, if your end caps are on, make sure we get those out of the way. If they're locked, go ahead and just use the provided key to unlock it. But now we're going to fit the bolt through this hole here on our clamp and make sure that it threads into that opening there inside our tower. Once you get the bolt here to start threading, it's probably gonna be easier just to use the tool to get it most of the way in. In our case, I'm gonna go to about 70, 75% here. I'm not gonna tighten it down all the way 'cause it might start pulling the whole system towards me, rather I'm gonna tighten this one down, and then I'm gonna go back to the other side, tighten that one down, come back and finish this one up, and then finish the other side up as well just to make sure everything's even as possible. Now that we've gone back to the other side and tighten that one down, I'm gonna finish tightening this bolt here. Again, just using this tool. Once it gets to the point where it straightens out, that's how you know we're at the desired torque. So I'm right about there now. All that's left to do is to replace our end caps and lock those up. So overall, if you're looking for a really effective way to extend your load space, whether that's getting some larger or longer items up on your roof, the Rhino-Rack Vortex Aero Roof Rack System is gonna be a great option for you. We just took a look at how to install it and how it fits on our 2021 Ford F-150.
Average Customer Rating: 4.7 out of 5 stars (1830 Customer Reviews)
Aerodynamic, aluminum crossbars let you build an aftermarket roof rack for your vehicle. Full-length bars provide plenty of space for carriers and accessories. Vortex strips in C-channels reduce wind noise. Theft-deterring plastic locks included.
i George from etrailer,
The rack is awesome! Strong, firm hold and nice looking. When doing surveys, I put my ladders on the rack.
I highly recommend this etrailer.
I put 3 stars because its a useful functional non-harmful roof rack solution for my WRX sedan. This review lost 2 stars because the rubber top pieces get damaged upon any accessory removal or install like(bike, snowboard rails etc). Additionally, these accessories also look to be weathering quickly because of build quality. Hopefully this helps your decision! Thanks
Once installed the product is very sturdy and looks great. But the directions are hard to follow because of the separate components and would have been really tough without the video which was great. I have one problem, how can I eliminate the annoying wind sound when driving when nothing on the rack. I saw a video where wrapping a line around the crossbar can help. It has helped a lot but not completely. Is there another secret for this?
The rubber molding easily compressed and served no purpose other than to fall into the channel and thus shred the aluminum gunnels on my expensive Kevlar canoe. I contacted Rhino rack and they were quick to dismiss my information with zero concern or questions. This is a product easily made better with modest changes to improve. Too bad customer service doesn’t exist…
Used my rhino rack traveling thousands of miles over the past year. They are a great product for the price, no need to buy the expensive big name products. Highly recommend these roof racks.
The rhino rack is well made but suffers from the flat bottom rubber feet. Since nearly all cars and trucks have roof seams, foot pads should be stepped to engage the seam like other racks such as Thule does. It's unlikely that very many different shapes would be needed to fit most vehicles. Rhino tech didn't agree with my assessment.
Not too hard of an install and it looks great! Highly recommend for a basic utility roof rack for your 23 Tacoma.
Superb fitment. Precisely fits the roof of your car giving me confidence lugging my canoe or car top carrier around. Reasonably priced. You can tell the feet were designed specifically for your car. I've recommended etrailer and this Rhino Racks to several friends. Installation is super easy too with included measuring tapes, stickers to always return the mounts to the same location, etc.
Bought as part of a Rhino-Rack Aero bar roof rack. Built solid and assembled easily. The keyed locks work perfectly. If you do install these make sure you check the rack for looseness every so often or before a trip. It's easy to open the cover and tighten the bolt just to be sure.
For the honda fit the Rhino rack system is the only rack that will fit. Because the Rhino rack is a one size fits all it is complex and fiddly. I would not recommend it unless there were no other options available.
I've been using my Rhino-Rack primarily for hauling up to two kayaks. It has performed very. On the particular trip we are on now we went thru some pretty high winds blowing from the side of our rig and the kayak stayed secured. I would highly recommend this for anything you want to carry on top of your vehicle.
The selection process that etrailer uses is top-notch. This really helped narrow down the choices for my 2019 RAM Quad cab. I bought this all kitted together. The assembly process is very straightforward and well-documented. I would highly recommend etrailer as a source for vehicle accessories. I have Yakima bike racks on our Subaru and this is as good if not better.
Rhino-Rack installation was fairly easy. We’re using it on a 2012 model Ford Flex.
I liked doing business with you. I like the products I ordered. I did have trouble with part of the shipping. It was not your fault, but the part of the shipping you used The USPS did not work. I neverrnecieved the item from them and you had to ship me another via UPS. Over the last 10 years I have had a number of problems with the USPS with packages and mail. They are especially difficult to get information from when something seems to be lost. I would recommend not using the USPS for your shipping needs. Again, I am very happy with you and the products I bought from you.
Awesome cross bars
Fit perfectly for my CR-V. Have had no issues with them after a year use. They are removable, but I leave them on because it took me forever to install them and I forgot to use the included stickers to mark where they go. I haven't removed them to know whether they have damaged or scratched the paint, but functional wise they're great if you have a naked roof.
being a part of a system, they alone aren't spectacular but do what they need to
Mounts great to my F150. Carries my canoe perfectly. With kayak attachments it carries those well. Nice to have a roof option to keep the bed open
Absolutely love the Rhino Rack. Easy to install (watch the [online] video). Looks GREAT. Hauls my kayaks no problem. Very well made and I highly recommend this product.
This rack has not scratched my car which is very important to me. I have used this rack on Very bumpy dirt roads and my kayaks have been held on by the Rhino rack as expected.
Love my Rhino rack. Very sturdy and easy to install. Highly recommend!
Works great with the rhino rack for hauling Kayaks.
Great rack for a great price. I tried an Amazon knock off, and that was a piece of junk. The Rhino rack is relatively easy to install, is very secure, and has lots of accessories.
The installed rack has done the job well and after installing and breaking down after one ski season and then reinstalling for the next season, no issues or problems to report. Everything has worked out great.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.