The Axle-Less system provides a smooth, quiet, safe ride and can eliminate the need for an axle, allowing for maximum ground clearance and a low deck height. Suspension units replace your existing axle and operate independently. Fits any frame width.
Features:
Specs:
Note: The Timbren Axle-Less suspension system may require additional support on your trailer. If your trailer does not have a crossmember above the spot where you want to install the Timbren system, you may need to reinforce the frame. You can accomplish this three ways. First, you can retrofit the trailer with a crossmember. Second, you can build out the trailer frame. Third, you can use standard, 2-inch steel tubing to connect the 2 Timbren suspensions together using the built-in square hole on each unit.
Ride on rubber with Timbren's Axle-Less trailer suspension system. This one-of-a-kind suspension consists of two separate units, each containing rugged steel arms and two strong, hollow rubber springs. Overall, the system safely and effectively absorbs road shock, minimizes trailer bounce and rattle - regardless of load size - and helps to protect your trailer's components and cargo. Built-in camber and toe-in keep your trailer tracking straight to minimize tire wear. Integrated hangers attach to your trailer's frame. And 2-inch holes make it easy to reinforce your trailer's frame by adding standard, 2-inch-square steel tubing (if needed).
The Axle-Less independent suspension system replaces your trailer's existing leaf spring suspension and can eliminate the need for an axle. The independent action of the suspension reduces roll when your trailer is cornering and allows you to maximize ground clearance and minimize deck height. Your trailer can have the same side-to-side clearance as your tow vehicle. And the low deck height makes it easy to load cargo from either the rear or the side.
Because you're riding on rubber, your trailer will ride smoothly and comfortably, whether you're navigating rocky terrain or highway asphalt.
The Axle-Less suspension's progressive spring is a definitive upgrade over leaf springs. Although leaf springs deliver a stable ride when supporting a load, a trailer with leaf springs will bounce and rattle when it's empty or supporting a light or off-center load. On the other hand, your trailer can bottom out on bumpy roads if the load is too heavy. The AEON progressive-rate springs of the Axle-Less suspension always deliver the same reliable performance, no matter the load size. As more weight is added to the trailer, the springs compress and become stiffer, offering more support for heavy loads. And because they rebound more slowly than leaf springs, the AEON springs do a better job of absorbing road shock, thereby keeping your trailer from bouncing and rattling when you're carrying a light load. So with this versatile system you will enjoy a smooth ride whether you're towing an empty trailer or a hefty load.
Unlike leaf springs, Timbren's Axle-Less suspension units operate independently of one another. Each spring activates only when needed. This reduces roll and delivers top-notch performance, even when you're hauling off-center loads. When your trailer with leaf springs takes a turn, one side of the suspension compresses and takes on more weight, and the other side becomes looser and bounces. This causes rattle and can make the trailer lean to one side. But when your trailer with the Axle-Less suspension takes a turn, one side compresses and becomes more rigid to absorb the weight, and the other side expands to normal height to help steady the load and minimize bounce and rattle. The load stays better balanced, even if it is off-center.
Timbren's Axle-Less trailer suspension system is a great alternative to torsion axles. While both systems allow either side of the trailer's suspension to operate independently, only Axle-Less suspensions are actually separate units. Torsion axles still require a bar that spans the bottom of your trailer, whereas Timbren's system can eliminate the need for a thru axle - giving you the same amount of ground clearance from the front of your trailer to the rear. It also allows Axle-Less suspensions to fit any trailer width - unlike torsion axles, which have to be fitted to an exact frame width.
Axle-Less suspensions operate in a smoother, less stressful manner than torsion axles. Torsion axles use a twisting motion, where the bar inside the axle tube rolls against rubber cords or a rubber wall to create compression and resistance. The up-and-down motion of the main spring and the side-to-side motion of the rebound spring in Timbren's Axle-Less suspension work together to provide smooth, consistent compression - with no twisting - that results in a better ride and less stress on the suspension's components.
Whether you are building a trailer or retrofitting your existing trailer with the Axle-Less system, you must make certain that the trailer's frame is both perfectly square and sturdy enough to support a heavy load without the aid of a thru axle.
There are three ways to install the Axle-Less suspension. The easiest method, which is recommended if you are replacing axles on your trailer, is to install a piece of 2-inch-square tubing (sold separately - available at most weld shops) through the integrated hole in the Axle-Less suspension. Then all you need to do is bolt the suspension to the side of the trailer's frame with three bolts (not included).
The second option for installation is to fabricate an inboard extension plate that attaches the trailer's frame to the Axle-Less suspension.
The third method of installation is to bolt the Axle-Less suspension's hanger to the trailer's frame and to an existing crossmember that is in the area where you want to install the suspension.
With both the second and third options, you must use three bolts to attach the suspension to the side of the frame. And you also have to use two or three bolts to attach the suspension to the bottom of the frame extension, or crossmember. Both the second and third methods of installation will eliminate the need for a thru axle and provide the most clearance.
Timbren's Axle-Less suspension units should be installed directly across from one another. Before mounting the units, measure back from the coupler and mark the frame to make sure that the two distance measurements (A and B) are within 1/8 inch of each other. Then you can drill holes through the frame and attach the hangers with Grade-5, half-inch bolts (not included).
Average Customer Rating: 4.7 out of 5 stars (207 Customer Reviews)
The Axle-Less system provides a smooth, quiet, safe ride and can eliminate the need for an axle, allowing for maximum ground clearance and a low deck height. Suspension units replace your existing axle and operate independently. Fits any frame width.The trailer rides great down the road and no more worries about saltwater and rusty leaf springs. Not a cheap option but I’m very happy with the setup. When installing, just be sure to measure accurately and have sharp drill bits. A drill press type of guide also helps ensure correct drilling angles. The first picture is of a mounting gusset a local welding shop made. One is needed for each side and necessary to provide needed mounting strength-at least on my trailer frame. Pics 2 and 3 show the mounted suspension on one side of the trailer. Pic 4 shows the suspension on one side of the trailer with the axle attached and a separately purchased disc brake assembly mounted on it. Finally, pic 5 shows a 2” box channel between both suspension assemblies. Independent suspensions would have been nice, but I wanted to ensure trailer rigidity was maintained. So, after one year, so far, so good. It’s all smooth sailing down the highway.
A must have suspension if you're building an off-road trailer!
We use Timbren's ASR3500S06 on all of our XER trailers. We couldn't be happier. It is a well built suspension.
Best suspension you can get for off-road trailers. We use this suspension on all of our VORSHEER XER trailers.
You guys are awesome! Great how to vi deos.
Came late. Not e-trailers fault. Covid-19 and China's fault. They bolted right up on my trailer frame. Really like the way they make my tear drip trailer handle. No sway, no bouncing all over like it use to. Will always put these under any trailer I build from now on. E-trailer keep up the great work.
These are going on a single axle trailer. They appear to be heavy duty and well made. The shipping was quick.
Only been driving around on the axle-less system for about a week now and it has far exceeded expectations. I get better gas mileage, my trailer now sits like it was intended to, my trailer doesn't bounce like it used to, I wouldn't trade this axle system for any other. Just wish I would have known which outboard assembly arm my trailer needed with the axle-less system before I placed my order. Still not a problem though, plan on using the wrong outboard arm to build a different trailer. So far, a great product!
works great, only had one discrepancy, on a long trip part of the rubber on one side of the trailer worked its way out, it was repaired and hasn't given us any other problems.
The suspension I ordered is of high quality and I received it sooner than I expected , its good to do business with a company that produces its products so fast.
These are quality. Excellent ride height and clearance. Turns your ordinary trailer into a bulletproof beast.
Everything arrived in great shape and included easy to follow installation instructions.
Thank you Dena
Work great
Killer axles
Everything was delivered ahead of schedule and met the expectations provided by the sales person.
Wow. Solid build.
Review from a similar Axle-Less Suspension in Trailer Axles
Trailer suspension and disk brake performance is outstanding big big difference over leaf spring and electric drum brakes.
Installation required modifications to the frame to monut the timbren suspension
Review from a similar Axle-Less Suspension in Trailer Axles
They have more pros than cons, but the second set I bought broke the flat plate that holds the spindle at about 8 months. The steel quality seemed less than I would expect since it basically peeled it back like a pop can as you can see in the pictures. Otherwise I like the clearance and ride. They last 2-3 years where the torsion axles I replaced would wear out in 4 months after driving down rough gravel roads. There is a grade zerk on the underside which I didn't realize until I bought the second set. That would have helped the first set last longer had I known about it.
Review from a similar Axle-Less Suspension in Trailer Axles
I used these axles in a different way than most would. I needed a trailer that was small, could handle tight switch-backs, carry 600 lbs and be light. I had this idea and as a retired design engineer I saw a great possibility in this axle. I have made four of these trailers now, one as a camp trailer, 2 for trail work for State Parks and one as a utility trailer.
Review from a similar Axle-Less Suspension in Trailer Axles
Needed a suspension system that I could make a low profile kayak trailer, that would fit in a specific area next to my garage. These were excellent that I could make the trailer any width I wanted. Easy to install and well made.
Do you have a question about this Trailer Axle?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.