Designed for use with wide, off-road tires, this setup gives you more clearance and a smooth ride. Built-in shock absorption limits rattle and bottoming out. E-Z Lube, long, standard-height spindle maintains deck height. Fits any trailer frame width.
Features:
Specs:
Note: This Axle-Less system requires crossbeam support. If your trailer frame doesn't have a crossmember in place, you can retrofit it with one, or you can add a support by running a piece of 2" x 2" steel tubing through the square holes cut into these units. You could also add a steel reinforcement bracket to the inside of the trailer frame.
Get more ground clearance and a more comfortable ride when you're towing with Timbren's Axle-Less trailer suspension. This suspension system provides great shock absorption to comfortably get you where you need to go and to protect your precious cargo as you travel - even on rough terrain. With 2 independently operating units, you'll get better handling when making tight turns. And because this system eliminates your axle and has standard-height spindles built in, you'll get more clearance without having to raise your deck height.
There are many suspension options for your trailer or camper. So, what makes Timbren Axle-Less different?
Axle-Less systems are a definitive upgrade over traditional leaf springs, in part because they allow you to do away with your thru-axle, allowing for maximum clearance. As you've probably noticed, having a leaf spring suspension means that your axle will always hang at least a few inches below your trailer's frame, resulting in limited ground clearance. This may make it difficult to navigate off-road terrain.
In addition, while leaf springs do a great job of supporting an even load, they may cause your trailer to bounce and rattle when it's empty or to bottom out with a heavy load. And they don't offer any type of shock absorption for a smooth ride - unless you have upgrades built in. With Timbren's Axle-Less system, gone are the days of dealing with these annoyances - this suspension is designed for a quiet, balanced ride, whether your trailer's fully loaded or empty.
A torsion axle is a step up in terms of shock absorption, and it provides more clearance than a traditional, leaf spring suspension, but that crossbeam will still hang down some. And if your torsion axle gets damaged in any way, it can't be repaired - you'll have to replace the entire thing with a setup that matches your exact trailer frame width.
With the Axle-Less system from Timbren, you won't have a low-hanging axle beam to get in the way when you want to go off-road. The standard-height spindles on this setup will keep your deck height the same, so you'll get that extra clearance and still be able to easily load and unload your trailer. And the rubber springs and independent operation both combine to absorb shock and deliver a smooth, easy ride. In addition, the Axle-Less system can be easily maintained over time, and it will fit any trailer frame width, so you don't have to worry about potentially ordering the wrong size like you might with other systems.
Another suspension upgrade on the market is Timbren's Silent Ride. This setup is a great option to reduce bounce and rattle because it has the same AEON rubber springs as the Axle-Less system. But the Silent Ride still requires an axle, so you won't get the same ground clearance or low deck height as you will with the Axle-Less suspension.
The Timbren Axle-Less suspension is designed with you in mind. All of the parts work together so you can tow your trailer comfortably - regardless of load size.
The first step in installing the Timbren Axle-Less suspension is to make sure that the mounting points for each unit are directly across from each other. The easiest way to measure this is to mark the desired mounting points on your trailer's frame. Then measure the distance between these points and the center of your trailer coupler. These measurements (A and B) need to be within 1/8" to keep your trailer frame square.
Once you have your mounting points lined up, you'll be ready to install the system. Drill 3 holes into your trailer frame at the desired mounting points. Then bolt each unit to the frame with Grade 8, 1/2" bolts (not included).
Because Timbren's Axle-Less system eliminates your trailer's thru-axle, you'll have to find another way to get the crossbeam support that keeps your trailer frame square. You have a few different options to do this depending on your application and how much fabricating you're comfortable doing.
If you're building a trailer, the best option is to begin building with the Timbren Axle-Less in mind and include a crossmember where you want to install the units on your frame. You can also retrofit an existing trailer with a crossmember.
If you don't have a crossmember where you want to install the Axle-Less system (and you don't want to add one), pick up a section of 2" x 2" steel tubing from a nearby weld shop. This tubing will serve as a support to keep your trailer square. It will hang only about an inch down from your trailer frame, providing more clearance than a thru-axle.
After you've mounted both of the units to your frame, you'll need to drill 3 holes into the steel tubing and into the built-in, square holes. Then, insert the tubing through the holes and secure it with 3 bolts (not included) on each side.
The last option is to fabricate a reinforcement bracket that can be attached to the inside of your trailer frame and to the Axle-Less suspension. It may be a little harder to fabricate a compatible bracket than to mount steel tubing, but you may get additional clearance with this method.
The following diagrams show measurements taken on the Timbren Axle-Less suspension system.
A | B | C | D | E | F |
---|---|---|---|---|---|
13" | 19" | 1" | 5" | 5-15/16" | 4-1/4" |
G | H | I | J | K | L |
---|---|---|---|---|---|
5-5/8" | 8-1/2" | 4-3/4" | 1-3/4" | 3-3/8" | 3-11/16" |
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello neighbor Steven here with etrailer.com. Today we're looking at the Timbren axle lift trailer suspension with the heavy duty long spindle and a four inch lift. Now folks, this is what they consider a five volt spindle and it's rated at 7,000 pounds capacity. Now folks, I'm kinda limited on space today, so I wanted to kind of throw everything up here the best I could and give you an idea of what you're gonna give. But I wanna start off, I show you an image so you will get all the hardware and everything you see in the picture. I don't have the hardware laid out today due to space.
So again, you're left and right hand side, two spindle assemblies and all the hardware spacers, castle nuts, Kotter pins, everything you see there. Now getting into it folks, this will help deliver a nice smooth, stable, quiet ride regardless of the load size up to 7,000 pounds. This internal jounce here is gonna absorb the road shock and also support your trailer's load. The spring does rebound, which is gonna reduce body roll rattle, bottoming out, those kind of things. And it has a built-in Camber and tow in to help reduce the wear and tear on those trailer tires.
The units do work independently, one from each side, so what affects one side will not affect the other side. So that's a nice upgrade and feature of these as well. Now again, I don't have the hardware laid out here, but roughly to show you what this guy looks like installed pretty much something like this and you'd have it all bolted together obviously and everything. It does have a nice black powder coat finish. It's gonna resist rust and corrosion.
It is super, super thick, very robust, heavy gauge steel construction. It's gonna handle all the road abuse that you can send its way. Now the long spindle here accepts wide Off-Road Trailer Tire, so that's a nice feature and it is two separate units so you can bolt directly to your trailer frame and it is designed for like over-landing, off-road, that kind of stuff. Now the nice thing with a drop spindle is that it'll keep your trailer deck height the same but increase the ground clearance. Now everything here has built-in greaser, so you can see on the tip of the spindle there to make maintenance and that kind of stuff, minimal and easier to get to.
So it's compatible with the tire size of 235 85 16 or larger, and a wheel diameter of 16 inches or larger, the bearings and everything is sold separately. That's part number 25580 on the inner bearing. And the outer bearing is a 14125A. And then those matching races are sold separately. The grease seal would be a 10-36 also sold separately. Now folks, this is designed for a single tandem use trailers. Do not use it for three axles, it's all rated for two axles, most. Now if you want to do two axles, you would need two sets of this kit. Now keep in mind your hub drums, all that stuff is sold separately, 7,000 pound capacity. And one other thing to note that you can kind of see the square that goes all the way through. Let me zoom in here. So this square goes all the way through. That's for installing a cross beam support. So this axle system still requires a cross beam support. If your trailer frame doesn't already have one in place, you can retrofit it by simply getting a two by two inch steel tubing and run it through those and cut it to length as needed. Or you could also simply add a steel reinforcement bracket on the inside of the trailer frame. Well, I think it's gonna wrap it up for our look at this Timbren axle list trailer suspension. Again, you're getting the whole kit, all the hardware and everything included as you see in the photo there. Folks, thank you so much for your time. I'm Steven, thanks for watching and have a great day.
Average Customer Rating: 4.6 out of 5 stars (312 Customer Reviews)
Designed for use with wide, off-road tires, this setup gives you more clearance and a smooth ride. Built-in shock absorption limits rattle and bottoming out. E-Z Lube, long, standard-height spindle maintains deck height. Fits any trailer frame width.Very smooth pull. I'm very impressed on how the trailer pulls. My traditional axle trailer seemed to bounce a lot on the highway which made a lot of noise, but with the Timbren Axle-less that I installed on a new trailer, the trailer is so smooth and way less noise.
Great product.
Installed the Timbren Axle-less suspension a little over a year ago and approximately 5000 miles ago. I have been extremely satisfied with the installation and performance thus far and have had no issues. I also chose to install an optional crossmember for more strength using a 1/4" thick piece of 2x3 steel. I had to increase the weight capacity of my campers suspension due to renovating the interior completely and adding more weight. I also strengthened the frame to accommodate the extra weight. In addition to installing the Timbren 5200LB system I installed new 12" electric brakes and upgraded to 225/75R15 tires with E load range rating.
I am satisfied with the overall craftmanship of the product. But I was disappointed with the welding on the spindles. none of the weld splatter was buffed off, and the welds looked gobbed on, unlike all the other welds which look good.
The axle-less suspension worked very well for my boat trailer. The suspension was easy to attach to the trailer frame and provided a lower profile than the traditional leaf spring and axle system.
The trailer rides great down the road and no more worries about saltwater and rusty leaf springs. Not a cheap option but I’m very happy with the setup. When installing, just be sure to measure accurately and have sharp drill bits. A drill press type of guide also helps ensure correct drilling angles. The first picture is of a mounting gusset a local welding shop made. One is needed for each side and necessary to provide needed mounting strength-at least on my trailer frame. Pics 2 and 3 show the mounted suspension on one side of the trailer. Pic 4 shows the suspension on one side of the trailer with the axle attached and a separately purchased disc brake assembly mounted on it. Finally, pic 5 shows a 2” box channel between both suspension assemblies. Independent suspensions would have been nice, but I wanted to ensure trailer rigidity was maintained. So, after one year, so far, so good. It’s all smooth sailing down the highway.
Huge improvement over the factory leaf springs. The suspension is so nice and quiet, I forget I’m towing. Very rust proof as well with many dips in saltwater with no signs of oxidation. Not the easiest to install but it’s nice to have the option to either weld or bolt on and replaceable spindles insure the suspension will likely outlast the rest of the trailer.
Purchased 2 sets of the Timbren 1200 Axle-less systems for upgrading the suspension on an older 30' ft glider trailer. Single axle with small (13") tires made towing tough due to porpoising, dragging on drive entrances do to poor flotation; also German made and metric, no repair parts. GVW 2000 lbs equated to bouncy ride.
Dual sets now allow the trailer to ride over bumps and sharp inclines easily, smoothly, little bounce on country roads; porpoising is history. My glider now rides securely, safely, quietly.
Install time 4 1/2 hours (includes head-scratching). Results are outstanding, units are totally solid. Recommend the square tube interconnect, easy and quick - trailer frame was on the light side, so a precautionary fix. Clean look underneath.
Ordered 5 wheels w/tires, very nice.
Helpful neighbor so impressed he ordered a HD single set for his new DIY snowmobile trailer.
Customer satisfaction 100%, from phone order, online support, product information, immediate shipping, install instructions, followup... HIGHLY RECOMMENDED!
The service from etrailer has been great! They have been very helpful through the entire purchasing process. My one star is due to the quality of the product. First, for something as heavy duty as these are, you’d expect better packaging. On arrival, one of the spindles was sticking out of the box and the hand holds were torn on one of the other boxes. I was a little worried what I might find in the damaged box but everything seems to be intact. The disappointing part is the quality of the welds. For the price you are spending on these, I would expect a higher quality of fabrication. There is undercut in the welds that hold the three support plates together and big ol sloppy welds every where else. Unsure of what to do as my trailer has been designed around this suspension system.
Trailer suspension and disk brake performance is outstanding big big difference over leaf spring and electric drum brakes.
Installation required modifications to the frame to monut the timbren suspension
I purchased the 3500 lb. set w/4" drop. Wish they made a 2" drop. Install was fairly easy, but most of your time will be consumed with alignment measurements, acquiring shims, and making adjustments. I was lucky to have a very square trailer frame. However, the "slop" in the all of the mounting bolts (especially, the spindle mounts) is more than the 1/8" window they specify. You will want to preload all bolts before tightening, and then measure for alignment/toe-in. The units are supposed to have camber built-in, but it's not near enough (more shims). Also, this suspension has more travel then the documents indicated. I had to re-mount my fenders 1" higher to keep the tires front hitting. When fully loaded, you might have 1" of travel left. All that being said, the ride is better than I anticipated. It's less bouncy than a torsion axle, and very quiet. If I was building a trailer from scratch, I would use this system, again.
I used these axles in a different way than most would. I needed a trailer that was small, could handle tight switch-backs, carry 600 lbs and be light. I had this idea and as a retired design engineer I saw a great possibility in this axle. I have made four of these trailers now, one as a camp trailer, 2 for trail work for State Parks and one as a utility trailer.
I rebuilt a 4 x 8 trailer using the Timbren Axle-Less Trailer Leaf Spring Suspension and it works great. I would recommend it to others.
They have more pros than cons, but the second set I bought broke the flat plate that holds the spindle at about 8 months. The steel quality seemed less than I would expect since it basically peeled it back like a pop can as you can see in the pictures. Otherwise I like the clearance and ride. They last 2-3 years where the torsion axles I replaced would wear out in 4 months after driving down rough gravel roads. There is a grade zerk on the underside which I didn't realize until I bought the second set. That would have helped the first set last longer had I known about it.
It is important to know that your wheels are going to sit very tight to the trailer frame. I needed to add an extension to the hub for it to clear the sides of the camper I built.
These units install easily, are well made, and perform great! The trailer doesn't bounce around like you see a lot of trailers do while traveling down a bumpy road. I traveled some unpaved roads with no issues. I am certainly glad I went axleless. I installed with 15" tires. Problem is I didn't go big enough.
I intended to install on an existing trailer that I had. Changed my mind and built a new trailer. The new trailer came in heavier than I had planned. 2k pound capacity is now too small. I have to watch what I load the trailer with so I don't over load the suspension. I intend on buying the 3500 pound units when I have the money.
Timbren saved our RV road trip! The leafs on the axle on our 2018 Jayco TT came apart while driving in Maryland. We tried going to the manufacturer, but they were useless. Going to a RV mechanic meant being grounded for at least 2 months. Then we found Timbren. With the help of Timbren's excellent staff we purchased axle-less system through etrailer, who made sure we got as quick as possible. It came ahead of schedule, my husband installed the Timbren system and we were back on the road! The axle-less system is better than the original manufacturers. If you plan on taking your RV or TT farther than 100 miles GET THIS INSTALLED and get it through etrailer.
This suspension system did EXACTLY what I wanted. I replaced the leaf springs, axle/hubs on my small trailer. The new suspension improved the capacity, lowered the bed 4+inches, improved ground clearance and allowed me to rebalance the trailer all WITHOUT having to have any welding done. Everything needs to be measured very exactly and the alignment technique is fairly cumbersome and takes a bit of time. In the end, I have a quiet, steady, strong, low riding trailer. What more could you ask for
The order came in on time and the customer service at etrailer.com (Ashley) and Sean from Tmbren was outstanding. They both were very helpful in my choosing the right product for my needs. The axle less suspension's performance is absolutely superb. It vastly improves ride quality. I am using it on a teardrop camper that often goes on gravel roads and the raddling sound from the leaf axles was horrible. A couple of points to consider before you settle on the axle less suspension: keep in mind that you will lose some hight of the trailer. While you will gain clearance from the lack of the axle, the suspension will make the trailer sit lower than before.i had to lower my hitch by an inch to maintain the trailer leveled. Also it does appear to compress at higher rate than the leaf springs, which makes it softer but easier to reach it's limit. Overall this product is absolutely a must if you are looking to improve the safety and the quality of your towing.
Incredible system. Handled our Overland trek through Colorado and Moab. These axles on our 1917 Ford bed ran multiple Jeep Badge of Honor trails. The suspension handled flawlessly. Handles off camber rocks and drop offs smoothly. We ran the 4 inch lift and off road offset to fit the factory Jeep wheels.
Installed the Timbren Axle-less suspension a little over a year ago and approximately 5000 miles ago. I have been extremely satisfied with the installation and performance thus far and have had no issues. I also chose to install an optional crossmember for more strength using a 1/4" thick piece of 2x3 steel. I had to increase the weight capacity of my campers suspension due to renovating the interior completely and adding more weight. I also strengthened the frame to accommodate the extra weight. In addition to installing the Timbren 5200LB system I installed new 12" electric brakes and upgraded to 225/75R15 tires with E load range rating.
We made an amazing creation out of those two axle-less axles.
We made a large fuel cell that is used for offroad use and it has worked excellent this entire time.
They are really great products and we would love to work with them again.
Actually, we do a ton of social media stuff and youtube and if you ever have interest in sending us products to build content around, I would love to have the opportunity!
Thanks,
Michael Brandt
Garage Bound, LLC (On Youtube and Instagram and all the other socials)
We use Timbren's ASR3500S06 on all of our XER trailers. We couldn't be happier. It is a well built suspension.
I put these on an off-road trailer build. They have been fantastic! I've done many miles and they held up great. Highly recommend.
Had a broken torsion axle on dual axle boat trailer. Manufacter six to eight weeks to replace. Got this product in week. Installed same day. Very happy .cancelled new Axel order.
Needed a suspension system that I could make a low profile kayak trailer, that would fit in a specific area next to my garage. These were excellent that I could make the trailer any width I wanted. Easy to install and well made.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.