bing tracking image
  1. Trailer Bearings Races Seals Caps
  2. TruRyde
  3. Bearings
  4. Standard Bearings
  5. 2500 lbs Axle
  6. 1.375 Inch I.D.
Replacement Trailer Hub Bearing - LM48548
TruRyde

Replacement Trailer Hub Bearing - LM48548

Part Number: LM48548
In Stock
$7.81
Retail:$21.72
You Save: 64%
Trailer Bearings Races Seals Caps
Add to cart
LM48548 - Standard Bearings TruRyde Trailer Bearings Races Seals Caps
zoom in icon
slider vertical icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

Need help with installation?
Locate installers near me
High-quality, tapered roller bearing. Replacement part uses industry-standard number. Great Prices for the best trailer bearings races seals caps from TruRyde. Replacement Trailer Hub Bearing - LM48548 part number LM48548 can be ordered online at etrailer.com or call 1-800-940-8924 for expert service.
  • All Info
  • Reviews (26)
  • Q & A (0)
  • Videos (2)
  • Photos

TruRyde Trailer Bearings Races Seals Caps - LM48548

  • Bearings
  • Standard Bearings
  • 2500 lbs Axle
  • 1.375 Inch I.D.
  • Bearing LM48548
  • TruRyde
  • Race LM48510

High-quality, tapered roller bearing. Replacement part uses industry-standard number.


Features:

  • Inner diameter: 1.375"
  • Matching race (sold separately): LM48510
  • Application: inner bearing for AH25555F agricultural hub


LM48548 Replacement Bearing





Video of Replacement Trailer Hub Bearing - LM48548

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.




Video Transcript for Feature Review Replacement Race for 02475 Bearing

Speaker 1: Today we're going to take you through the rebuild process on a couple of hubs. We've got an idler hub, and here we've got a hub and drum assembly. Works with electric rigs, but this can also work for just standard discs, if you've got a disc brake style setup.Basically what we're going to show you is how to get all of the bearings out. How to remove the seal. How to remove the race's if they're damaged, then get them replaced in the proper manner. We'll show you how to use an easy loop hub, which we have here.The first thing we are going to need to do is, get the grease cap off the end.

It can have either a rubber plug in it like this one does, or it can be a solid metal cap.These are pressed fit in there, basically by tapping on them on the back side. To remove them, a deadbolt hammer is typically what we're going to use. We're just going to start tapping as we go around. You'll see a little separation start right here, and slowly it'll work it's way off.Now the next step's going to vary a little bit depending on your axle setup. Do you see this is going to have a keeper that goes around the nut.

And that prevents that from being backed off, or removed. A lot of times you'll have a castle nut, which will have just little tabs that stick off, and there will be a cotter pin that passes through it. Just depending on your application, you need to get the keeper for the nut off. This style we just kind of pry out. A cotter pin you would just remove of course.Once we have that off ...

We'll start to take off the nut here, and the washer that's in behind it. Now yours should look a whole lot more dirty than this. There should be a lot of grease packed in, and through the hub, this one's brand new. We thought it'd be nice to show you the components before the grease was on .. Of our washer that comes off.And then here we're going to have our outer bearing.

Continue to pull that. We're gonig to have our inner bearing here. That sits in the backside of the hub. And we didn't put it in yet, we will show you how to put it in. But a seal would typically be covering the backside here. We'll show you how to use a seal removal tool, or another tool. To get that pried up and out. To get an access to that inner bearing.Now for a drum style like this, that process for disassembly is going to be just the same. One thing to keep in mind if you're using a disc brake setup. You'll have to remove the caliper before the disc is going to come off.Now once we have the spindle exposed, as we said this is going to be really greasy. We want to get all the grease removed, and the first thing we'll do is inspect it. We want to make sure that it looks just like what we have here. Everything's nice and smooth. We don't see any kind of discoloration, or any marring on the metal. Indicating that our bearing's got hot.If you do have any of those symptoms, at this point it's time to replace those bearings. You don't want to repack them. Get new bearings, and put in there. You might have a bearing that's come apart in here. Another surface to ensure is in good condition, is where your seal is going to go. That helps seal all the grease inside of our hub. With a damaged or broken seal, that grease is going to seep out. Either out of the hub, or in this case into our brake assembly.Now if your axle has brakes, we're also going to check the disc. Make sure it doesn't have any issues, or your hub. And this is going to be a hub and drum assembly. The brakes are going to ride on this machine surface. You're going to check that for signs of excessive heat, discoloration, or cracking. And this is our magnet surface. We'll check that surface for the same issues.Now inside the hub regardless if it's a disc brake, it's a drum brake like this. Or just a standard idler style hub. You're going to have an outer race. Would be right here, it's a small tapered piece of metal your bearing sits in, and rotates on. That's basically the outer portion of the bearing.You have the same thing here on the backside. This is called the inner race. Now if those show any signs of wear, overheating, or cracking. Those are also something we'll need to replace, which we'll show you how to do in just a minute.Now, with your brake assembly exposed, if you do have electric brakes like we have here. It's a good idea to check all the components for wear, cracking, maybe missing pieces. Check your pad thickness to make sure those are in good shape. Basically if you have a non working brake assembly and you put everything back together, you're just going to have to take it apart and do it all over again to get back to the brake assembly. This gives you a really good option to be able to change them out.And most applications are going to use a four, or maybe a five bolt flange to hold them in place. And you'll just remove the lock nuts, or sometimes you'll have a hex nut with a lock washer. You want to remove those, and then simply slide your assembly off after you cut the wiring.The friction material itself should also be checked for any kinds of cracking, or overheating. If you have any grease inside the system at all, it's likely it's gotten on those pads. It's a good idea to get those changed. Now as far as the removal of the races go, it's going to be just the same whether we're using an idler style hub like we have here. A drum brake like we have here. You can basically see where the idler is, here in the middle of the hub. It's going to go all the way around there, and we just have this extra material here to provide our braking surface.Now if you're doing a disc brake style job again, it's going to be just the same here with the races living inside of the actual hub portion. You'll just have the discs there for the brakes to make contact. We're going to use this little bit smaller one, it's a little bit easier to manage to show you how to get these out. We've talked about where the races are. The outer here, the inner being closer to the inside, but on the backside of the race there's a little lip. That lip's meant to stick out just a little bit further than the hub, and provide us an area to put our tool on, and help to drive that out.If you look all the way through there on that inner race, you'll see that little lip that sticks out just from the hub slightly, and it gives us enough area to use our tool on. Now generally to remove these you're going to use a punch, similar to this. Some guys will use a screwdriver. Or a piece of pipe. If you have a piece of pipe that's small enough to fit inside of that diameter, you can take that down through and allow it to rest on that lip.Use our punch, and then just need a hammer. And we'll start working that out. We're going to tap all the way around. Kind of equally, and evenly apply the force to get it to come on out of the bottom for us.You can see now as it starts to come out there's going to be a little gap created between the hub and the race. And we can just keep going, bringing it on out. Then you can inspect the inside of the hub surface there. Make sure no damage or anything has occurred, and repeat that same process for the outer race if you plan on removing and replacing that one.Now in the outer flat edge, you can see we're going to have our tapered edge on this side. If we roll our race over to the flat side, typically there's going to be a manufacturers part number on there. That will help you identify which race it is, that you need to go back in your system. If those are rubbed off, worn off, if you can't read them. You can measure the outside, to outside diameter of the race here. It's a good idea to use a micrometer to get it exact.Now here's your basic micrometer. And again, the outside of the race is what we're going to need to measure. You want to go . I set the thickest point there. Looks like this one's going to be about 1.98. That's going to be the measurement you'll want to supply.Now while we've got this out, let's also look at the proper way to measure our bearing. Instead of the outside for the bearing, we need to measure the inside diameter. That's going to be pretty simple. Let's pull that out, find the largest measurement we can. Which here, looks like it's going to be 1.03. With that information, we'll be able to get the correct bearing, and the correct race, so they'll fit together properly and make a full bearing kit for us.Now here's the race, we're going to show you how to get this put back in. Basically just going to press fit inside of our hubs. We need to get it down on there. Kind of like that. And you'll have a couple options. A lot of times you're going to see do it yourself or at homer, just going to use a wooden block. Just place it on there. That's going to get you started, but at that point you'll struggle in getting it to go all the way down into it's seat.Now to take care of that problem, there are several seal drivers that are available. Seal and race drivers that are available out there on the market. It's designed to fit down inside of our race, inside of our hub and get it down there where it needs to go. This is part number ptw83020, has several different sizes, even if you have multiple trailers it's going to do the job.Now the side with the angle on it, is designed to fit down inside of our race. If we use the other side, that's going to be for driving your seal into place. Just want to hold it, and take it on in with your hammer. You'll see, you just want to insure that our race is all the way up against that line on the hub where it's supposed to mate to.Now when it comes time to pack your bearings you're going to have several different ways of doing this. You can just use your hand, is the traditional method. That's going to be the method probably reserved for the very occasional trailer work kind of situation. If you do it once or twice a year, probably get away with it that way.Next you would go to a, kind of a sandwich funnel style almost. If you look inside of there, you can see the bearing. It's located between the two pieces. Just use a grease gun. Start filling that with grease, and that's going to fill our bearing for us. And the third, with this one you're just going to place your bearing down and in. It should be pretty close to center. And then we've got our cone her that's going to go down and secure that.Now I think this style, wastes a little bit more grease than what this style will. This has a dust cap. You can see, you can keep your grease in there, put your dust cap on there and save it for later use. This will be if your going to do it every couple years. And this particular style would be if you're a more regular user.Let's start by showing you how to use a bearing packer. Similar to this. Again, we've just got our grease inaudible 00:11:07 here on the top. And then just slowly start to fill it. Now I like this style quite a bit. I think even regular users might enjoy it, because you can get a really quick visual look at that bearing. You're not going to have to overdo it, or have to much grease.You can kind of see in there now, we're starting to get grease to come out of it. Couple more pumps, we'll be good. You can see we've got grease coming out all the way around. Where all of our bearings are. Got a little bit of excess there. Just take that around the outside of it. And then we should be able to lift it off. And now you can see what we we're talking about. Just a little bit of excess there, that you're just going to wind up wasting.Now we'll take our bearing, we're going to place it right down in our race. And then we'll cap off the back with our seal. Right now our seal's going to fit in just like our race did. It's going to have a little bit of a pressure fit to it. Now very often in this situation, I see people using the four by four method. Kind of here, just placing that on and tapping it. As an option though, if you do have one of these. You can see that's designed to fit right on the top of the seal. And help drive it in.The biggest thing here is, just going to be getting it driven in squarely. You can see, this side's in a little bit further than this side. I'm going to start this side first. Now since we didn't have the opportunity to show you before, we're going to take a look at pulling a seal. Now this is a seal puller, we carry this on our website part number ptw1219. This is meant to hook underneath the seal. And then you kind of pull up on it, and just like our race you'll have to work all the way around that edge. Just bringing it out a little at a time.If you don't have that available. Another option would be a screwdriver. You just kind of get that under the seal, and turn it. And see, that'll allow you to also pop that out. We've taken care of our race. Our inner bearing. Our seal. The last component, before we put our hub back in place is going to be our outer bearing. Now with this bearing, I'll show you the hand packing method.This is definitely . Slightly dirtier method than the bearing packer. When we get grease on our hand we want to look at the larger side of the bearing. This is the smaller side. We have a larger side In between the inside and outside there's a gap. We can see our rollers in there. We want to grab that, and use that gap and shove grease inside of it. Now this is going to take a little bit, you want to work in the same spot until you get the grease pushed all the way through. We can see on the top there we've got a little bit starting to come through.And once we push it in the bottom, and you see it start coming out the of the top in those little drips, it's going to indicate that, that section's fully packed. Just need to work all the way around their outside edge now and do the same thing. Alright, once that's all the way around . The bearing will be ready for use.Now one more thing I like to do. We can see our inner bearing there, and our outer bearing. Well between the two, got a pretty big gap in there. If you'll take a . Pretty good amount of grease. We're just going to go all the way around. See how we can go all the way around the inside and just line that really well. The more grease we have in here, the less chance we have of any moisture getting in there, which can cause corrosion, rust, pitting. Pretty much things we do not like when it comes to bearings, races, and hubs.Put plenty of grease in there. And then this one does have the easy lube spindle, that'll even fill it in more. Now we can get our assembly slid on. I like to keep my thumbs on that outer bearing, just to prevent it from . inaudible 00:15:28 pushed off there. Now we can put on the original hardware that we removed, in taking off our hub the first time. In our case, we had our washer and our nut.Now most commonly you'll see pliers similar to this being used. We basically want to get that tightened down. Once it's fully tightened down you'll feel some resistance in the hub. We back it off just slightly. That'll give us a little bit more freedom of motion there. Something you don't want however . Is any movement in, or out on your hub. You want to be sure that everything is compressed, and you don't have what's called end play. Which would be the play in and out.Once we've got that set, then you'll put on whatever tight keeper yours came with. Get that put back in place. Now with an easy lube style hub, you're going to place your grease gun on the end, and then you can just fill the remainder of that hub up.Now for your typical applications, you're either going to have a solid cap, or a cap that'll have a rubber plug in it. A solid cap's going to be for an axle without the grease inaudible 00:16:51 here on the end. Goes on there. Just knock it on with your rubber mallet. Same with the one with the plug. Just gives you a removable area there, be able to cap that off.We'll show you how to put that on. Now as alternatives as well, a lot of times on boat trailers and marine kind of situations. You'll see a bearing buddy. This is going to apply a little bit of pressure on the grease, you'll fill it up. This kind of comes out just a little bit. That applies constant pressure on the grease to make sure we don't have any air, or anything like that. Then there is also an oil bath hub available. Now this is going to be for use with seals that are going to be designed specifically for oil bath use. You'll have to change that seal.We're using a double lip seal. There are also single lip seals available. Of course a double lip seal is going to give you just a little additional security. Keep that in mind when you order. But let's get this knocked on there now so you can see how that works. We just want to take the cap, we're going to center it. This is going to be very similar to what we did with the seal. And then just gently start tapping it around the outside. And it'll seep down on there for you.It's really going to be the same thing that you'll do with any of the end caps. Now with this side done, it's a good idea to take care of all the other hubs. Get them all on the same maintenance schedule. And as long as you'll periodically check the grease, take your trailer out for a trip occasionally. Just to keep everything lubricated. It should extend the life of these parts, and give us years of good service.

Customer Satisfaction Score:


Customer Reviews

Replacement Trailer Hub Bearing - LM48548 - LM48548

Average Customer Rating:  4.8 out of 5 stars   (26 Customer Reviews)

High-quality, tapered roller bearing. Replacement part uses industry-standard number.

by:

Great friendly staff



by:

I replaced all the bearings races seals and brakes on a small travel trailer. Bill P.at etrailer took my order and three days later I had everything in my hands. Great job Bill ! All the parts were exact replacements and the install went very smooth. There is video help on their website to show how to make the install easier. I have been dealing with etrailer for several years and have never had a bad experience. I was completely blown away by the pre assembled brakes . Backing plate, shoes, actuators, self adjusters and wiring all ready to bolt on. How much easier can it be? With the best prices, fast shipping and great help on line etrailer is the way to go.



by:

This was an order for replacement 40+ year old wheel bearing parts that had no identifying parts numbers. It was very hard to mach up, but etrailer provided enough information for me to locate the right parts.
The parts were deliver quickly with great communication and fit perfectly!
Thanks



by:

Again how much can I say about bearings?
After traveling almost 6500 miles with these on my 1969 Yellowstone Camper, they still are good and no problems



by:

bearings and seals all were fine. THANK YOU FOR YOUR SERVICE , Jay-



by:

good bearings I use them in off road highly abused environment and replace annually as preventative maintenance have never had one fail



by:

Everything looks excellent. Adam did a super job putting together this package. I will be buying from etrailer again. Thanks Louis



by:

It was delivered very fast!!! I got my bearings in 24 hours!!!
Thank you Amanda! The only thing I would suggest is that they should be packaged a little better, individually. They were all in a baggie inside the box. Other than that...very happy.



by:

So far so good!



by:

You guys are FAST, not half fast like other dealers!



by:

Crap.



by:



by:

good



by:



by:

Everything went awesome. I am not used to that. Thanks.



by:



by:



by:



by:



by:



by:



by:



by:



by:



by:


25
26
Show More Reviews

See what our Experts say about this TruRyde Trailer Bearings Races Seals Caps

  • Replacement Hub and Drum Assembly for Equipment Trailer with Mobile Home Axles
    Based on the measurements you have taken, the inner bearing is the # LM48548. This is a bearing for an agricultural hub and does not match any hub and drum assemblies with the # LM67048 outer bearing. This is common with mobile home axles. More often than not the only option is to replace the axle, which is what you will need to do if you want to change the hubs and drums to use different wheels. If you decide to replace your axles, you will need to know the capacity as well as the length...
    view full answer...
    Image 1 for
  • Replacement Bearings for idler hub with LM4858 Inner Bearing
    I have a solution for you, but we do not have any hubs that are compatible with the item # LM48548 inner bearing that you currently have. .003 is a tiny difference but that can still cause problems down the road so I do not recommend replacing your hub with the etrailer Trailer Idler Hub Assembly item # AKIHUB-545-35-K. You could continue to use your old hubs and simply replace the bearings. The inner bearing is item # LM48548 and for the race you'll want the Replacement Race for LM48548...
    view full answer...
  • Replacement Hubs and Brake Assemblies for Dexter Mobile Home Axle and 8-147 Hubs
    Based on the information you gave, although I can't help with the axle (other than to state it is a 3,500 lbs axle). Dexter mobile home axles were designed for one time use and weren't really documented for replacement parts, but because you have the hub number I can still give you the info you need for new drums and brakes. Your current Dexter hub 8-147 I was able to look up and it has an inner bearing # LM48548, an outer bearing # L44649, and a grease seal # 58846. Based on this information...
    view full answer...
    Image 1 for
  • Carlisle Electric Over Hydraulic Actuator Recommendation for Converting a Trailer With Surge Brakes
    I have a solution for you that you maybe didn't think of, but I checked the bearing numbers you gave and could not find any replacement hubs that match with both of those bearings. I would recommend you convert your trailer to electric-over-hydraulic brakes. Basically you will replace your surge actuator with an electric over hydraulic actuator and a hydraulic pump that is controlled by a brake controller will apply the hydraulic brakes of your trailer. EOH braking systems are literally...
    view full answer...
  • Replacement Bearings, Races and Grease Seal for Dexter 8-147 3500lb Axle
    Your Dexter 8-147 hub uses a # LM48548 inner bearing and a # L44649 outer bearing. The inner race is # LM48510 and the outer race is # L446910. The grease seal is part # 58846.
    view full answer...
  • Correct Seal For 2.562 Boat Trailer
    After running the numbers the Seal Set # BB60010 you were looking at is for the L68149 Inner Bearing or the 1.810 Bearing Buddy. I don't think that is what you're looking for. I found this Seal Set # BB60002 which is for LM48548 or L68149 Inner Bearing and also for a 1.980, 1.968 or 2.562 Bearing Buddy. The 2.562 matches the seal number you provide and this is the best match I could find on our site. I've included a video Randy made to help you with the install!
    view full answer...
  • Finding Replacement Bearing Sizes for 2006 EZLoader Trailer
    I spoke with EZLoader, who gave me your bearing sizes. The inner bearing is # LM48548, which measures 1.375 inches. Its matching race is # LM48510. The outer bearing is # L44649, which measures 1.063 inches. Its matching race is # L44610. You can also purchase a grease seal set, # BB60002. We also offer grease caps for 1.98 inch hub bores, such as the standard grease cap # RG04-020, and the EZ Lube grease cap # DC200L-DCRP. I've attached several review videos of these products for...
    view full answer...
  • Bearing Recommendation for Trailer with LM48548 and L68149
    We have the bearings you are looking for. You would want part # LM48548 and # L44649. These are not identical though. Then for a grease seal set you'd want the part # RG06-050.
    view full answer...
    Image 1 for
  • Replacement Bearings and Seal for Dexter Hub 8-147
    The inner bearings should be # LM48548 (1.375 inch inner diameter), outer bearing should be # L44649 (1.06 inch inner diameter) and the grease seal should be # 58846. I would recommend you pull your bearings out to verify that but that SHOULD be what you need.
    view full answer...
    Image 1 for
  • Recommended Replacements for an Older Trailer Hub
    Having an inner bearing # LM48548 and outer bearing # LM11949 is definitely going to make things a bit difficult. I went through all the hub options we have available, but none will match your set up, unfortunately. That being said, we should be able to get replacement lugs for you. This will depend on the size needed, but the # 7-122 will be 2 inches long with a 1/2 diameter, the # K916WB25 will be 2 1/2 inches long with a 9/16 diameter, and the # 7-232 will be 2 3/4 inches long with...
    view full answer...
  • Replacement 3,500 lb Spindle and Hub for Old Enclosed Trailer
    Since you have a very old enclosed trailer there are bound to be some parts that need upgrading and the issue here is that your inner bearing # LM48548 is for agricultural hubs and there isn't a replacement hub we carry that you will be able to use. What I recommend doing in order to convert your trailer to find parts much easier is to have your spindle cut off and have a new one welded on by a professional welder. For a 3,500 lb axle you can use the EZ Lube Spindle # TRU74FR and add the...
    view full answer...
  • Will The Spindle Grease Seal Set # BB60002 Work With EZ-Lube Axles
    Hey Jeromy, The # BB60002 is just a seal that sits at the back of the hub and wouldn't interfere with usage of the EZ-lube fitting. To determine if this is the correct fit you would need to measure your spindle at point B from the diagram below and the inner diameter of the trailer hub's bore hole. The description is a little confusing but essentially is just saying that this seal would fit if the spindle fit a # LM48548 or # L68149 Inner Bearing and then had either a 1.980, 1.968 or...
    view full answer...
  • Replacement Parts for 1970s Camper Frame with Dayton Fayette Axles
    The Lippert Components Heavy-Duty Replacement Shock - Yellow # LC283280 is 8.625 inches compressed and 13.5 inches fully extended. Your current suspension may extend and retract slightly further but the shocks will be a good replacement based on the actual shock absorbing as long as they will fit your brackets. Unfortunately we don't have any info on your axle or hubs, so to help, I will need to get the bearing numbers printed on the face of your inner and outer bearing of one hub. If...
    view full answer...
    Image 1 for
  • Replacement Hub Options For a Spindle Using LM48548 Inner and LM67048 Outer Bearings
    I can help you find some replacement spindles and hubs as we do not carry a hub which fit with the Bearings # LM48548 and # LM67048. The Trailer Idler Hub Assembly # 52655IEU gives you a new EZ lube spindle with a idler hub that accepts a 6 on 5-1/2" bolt pattern wheel. If you need a different bolt pattern to match your current wheels and tires please let me know your bolt pattern.
    view full answer...
  • Replacement Bearings And Races For Agricultural Hub
    What you have is an agricultural hub assembly. We will not have a replacement hub but we do offer replacement bearings and races. Inner Bearing # LM48548 Inner Race # LM48510 Outer Bearing # LM67048 Outer Race # LM67010
    view full answer...
  • Is There A Direct 5 On 4.75 Bolt Pattern Drum To Replace An Older Dexter 8-147 Drum
    I have had a few of the older Dexter 8-147 hubs pop up recently and we definitely have all the parts needed to do an overhauling of the internal parts. I have all these listed below, but with this having a unique bearing combination, there will not be a direct replacement hub available. In order to switch to a hub/drum with the 5 on 4-3/4 bolt pattern, like the # AKHD-5475-35-K, you will either need to replace the axle, or cut off your current spindles and replace them with the TruRyde...
    view full answer...
  • Are Trailer Bearings L44649 and LM48548 the Same
    The bearings part # L44649 and # LM48548 are not interchangeable. But since we carry both we have solutions for replacing both of them. If the races are good I would not mess with changing them. I attached a help article on adding e-brakes to a trailer as well.
    view full answer...
  • Recommended Axle Compatible With Electric Trailer Brakes To Replace Axle With Obsolete Bearing Combo
    I have a replacement axle option for you, but there is not a hub and drum assembly available that uses the inner bearing # LM48548 and outer bearing # LM67048 that your Agricultural hub uses. The only way to add electric trailer brakes to your trailer would be replacing the axle with one that has a more standard bearing combination. I recommend going with the Timbren Axle-Less Suspension - Spindle Only - Regular Tires # ASR5200S01 as it has a 5200 rating which is the closest option to...
    view full answer...
  • Replacement # LM48548 and # L44649 Bearing Recommendation for a Trailer
    We have the bearings you are looking for. You would want part # LM48548 and # L44649. For the leaf spring bushings you will need to take a coupler more measurements to pick out the correct one. You will need to measure the inner and outer diameter of the bushing to be able to determine which one you would need. Check out the link I attached to see all of the ones we carry ones you get those measurements.
    view full answer...
  • Replacement Parts for 18k Triple Axle Trailer
    Hi Jeff; assuming 3tubes meant 3" axle tubes/axle diameter you can use the Demco Trailer Brake Mounting Flange # DM52415 for 3" axles. However, if those bearing measurements are correct it indicates you have a # LM48548 inner bearing. We don't carry any hubs that use this bearing. I will also need to know the axle capacity to find the right brake assemblies. The closest thing we have for a hub and drum is the # 8-407-5UC3-EZ which uses the # L68149 outer bearing with a 1.378" inner diameter...
    view full answer...
  • Replacement Hub/Drum Assembly Needed for a Dexter 8-147 Assembly
    Your drum/hub that is the Dexter 8-147 part number should have an inner bearing # LM48548, an outer bearing # L44649, and a grease seal # 58846. If this is the case then we do have some hub/drum assemblies that would work great for your application. The hub/drum assembly that I recommend using is the part # AKHD-545-35-K which is compatible with 3,500 lb axles and has the bearings and seal that fit your spindle. It fits 10" brake assemblies so you will want to verify that on your end. This...
    view full answer...
  • Hub and Brakes for Vintage Camper With Dexstar Wheels
    Thanks for all the numbers and information. Since your trailer uses # LM48548 inner bearing we do not have a replacement hub and drum kit because of the spindle it uses. The # LM48548 bearing is only used on some agricultural hubs. So that leaves a few options, a new axle or an axle-less option. For a new axle you will need some measurements, you'll need to know the hub face to hub face dimension, and from spring center to spring center. The other thing you need to know is the weight capacity...
    view full answer...
  • Replacement Parts for Old Equalizer Brand Axle
    Given the measurements you provided, is sounds like you're needing a # L44649 (1.063 ID) and a # LM48548 (1.375 ID) bearing. However, we don't offer a brake assembly compatible with the 2-5/16 inch mounting flange bolt pattern you specified, and none of the hub/drums we offer are compatible with the bearings that your spindles use. If you can't find a compatible hub and brake assembly, your best bet would be to replace your existing axle with something that uses easier to find replacement...
    view full answer...
    Image 1 for
  • Grease Seal With 1.71 Inner Diameter, 2.62 Outer Diameter With Bearings LM48548 & L44649
    We do have a grease seal that is almost exactly what you measured that should work for you, with the outer diameter being 0.06 inches off, which could very easily be explained by the amount of pressure put on the caliper. So it is very likely that what will work for you is the Grease Seal # 58846. This seal has a 1.71 inner diameter and 2.56 outer diameter, and would be the only seal with dimensions close to what yours are. If you need bearings and races, we also have those: - Trailer...
    view full answer...


< Previous



Do you have a question about this Trailer Bearings Races Seals Cap?


Info for this part was:

Employee Jeff D
Installed by:
Jeff D
Employee Jameson C
Expert Research:
Jameson C
Employee Adam R
Expert Research:
Adam R
Employee Chris R
Video Edited:
Chris R
Employee Wilson B
Updated by:
Wilson B
Employee Alexander C
Updated by:
Alexander C

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.