Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If your trailer sees off-road action, use a handbrake (not included) with these brakes to hold it steady when parking on uneven terrain. 10" x 2-1/4" Assemblies fit 14" to 15" wheels. Made in the USA.
Features:
Specs:
Quick Tip: There's really not a whole lot to getting new drum brakes. If you've confirmed that all of the specs listed above line up with what you need for your trailer, you can be pretty sure these will work for you.
If you're looking to customize your off-road trailer or pop-up camper, these brakes can be a great way to do that.
Installing these brakes is easy, and using them is even easier. Run the linkage cable from your tongue-mounted handbrake (not included) to the backing plate of the assembly as shown above. Then, just pull on the handbrake any time you need a little reassurance that your valuable cargo won't roll away from you.
The more miles you put on your trailer, the more your brake pads will wear down. As they lose contact with the drum, stopping distances get longer and longer. To keep your brakes working great, it's important to adjust them pretty routinely. For this job, grab a floor jack and either a brake adjustment tool (sold separately) or just a standard flathead screwdriver.
Jack up your trailer enough to get the wheel(s) off the ground. Remove the adjuster plugs from the backing plate on the brake, and insert the flat end of the tool through the back of the assembly.
Push in on the star gear and lift it up. Keep doing this until the brake pads catch on your drum. When you can't spin your wheel by hand anymore, back the gear off by about 10 clicks by pushing down on the star gear. Does the wheel now spin freely (even if it sounds like the brake pads drag slightly on the drum)? Great! Then you're all done with that one and ready to adjust the rest.
After you get these brakes installed and adjusted, you'll need to break them in. First, find a long stretch of road or a big, empty parking lot. Once you're there, set your brake controller to its maximum setting and get moving. Speed up to about 40 mph and brake to slow to about 20 mph. Repeat this 15-30 times. The goal is to get the brake shoes and magnet properly seated into your drum. You'll know you've done that when it feels less jerky (and more consistent) each time you apply the brakes.
Note: The brakes will be very hot after doing this, so after every 10 stops you'll want to wait about 10 minutes to let the brakes cool off before continuing. If you don't, you might cook and crack the pad material.
Average Customer Rating: 4.9 out of 5 stars (26 Customer Reviews)
If your trailer sees off-road action, use a handbrake (not included) with these brakes to hold it steady when parking on uneven terrain. 10" x 2-1/4" Assemblies fit 14" to 15" wheels. Made in the USA.Purchased Dexter 3,500 lb backing plate assembly with brakes including manual brake. Parts were genuine Dexter. Installation has helped in the restoration of a Sloan Kwik Load car trailer I recently acquired.
Appreciate the etrailer employee followup, service, and pricing. Thanks so much.
really like the product, fit was as original, but don't understand why it took almost 3 weeks to receive
Great service and fast shipping.
etrailer's service and delivery was excellent! Very professional, fast and the staff were super helpful and knowledgeable.
Dexter's brake hubs, however, leave a lot to be desired. They couldn't put less paint on these assemblies if they tried! The paint is so patchy and thin that I will have to disassemble them, paint the components properly and reassemble before installing them on my trailer otherwise they will be rusty within days. Come on Dexter, if you are going to bother painting these assemblies then for goodness sake paint them properly!
Great. Easy to fit. So much safer than chocks. Would definitely buy for next travel trailer
At Ruger Trailers we have been getting more requests for Dexter electric brakes with the parking brake feature. After attempting to order through our normal distributors we were disappointed at the lack of availability and high prices. Went through etrailer and got exactly what we needed in two days at a very good price. Good experience!
Maybe you should add to your web page also bought with this product for instance I bought brakes and drum and forgot bearing kit witch I ended up buying local and would have bought from you
Perfect match.
Excellent product and definitely the way to go is with backing plates with all new hardware. AAA 5 STARS
Fast shipping, proper fit, good product.
OEM parts made in the USA - nothing's better!
fits and works great excellent service
Charles
4/14/2020
great
Bolted up perfectly
Do you have a question about this Trailer Brake?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
George
4/10/2022
It work great. Easy to fit and working 100