Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
9" Wide x 32" long x 15" tall. This sturdy, rounded fender has a durable backing plate that helps protect your trailer from debris. Ribbed, 16-gauge steel is built to last. Bolt or weld onto your trailer.
Features:
Specs:
Note: Do not use the backing plate to mount the fender to your trailer.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ellen: Hey everyone, I'm Ellen here at etrailer.com and we're going to be taking a quick look at the single axle trailer fender with backing plate. So this is a really great way to protect any drivers on the road from any kind of debris getting kicked up or slung up underneath your tires and causing any issues with them, but also it's going to protect any gear that you're hauling. With the backing plate included in this, it makes it really nice for open trailers as well, to make sure that no gunk or rocks or debris or anything is going to come up and damage whatever you're hauling, whether that be any kind of equipment, vehicles or anything else. So it's going to be a really nice addition to your trailer to make sure that everything is protected and that no rain or mud or water is getting slung up and slung around, and also to keep everything else in place on your trailer as well.This is made out of a 16 gauge, cold rolled steel. So it's going to be nice and durable. You can weld this in place or you can bolt it on, it doesn't have any pre drilled holes for bolting, but since it does have just a raw finish, you can weld it in place.
That being said though, once you get this in place, you'll probably want to prime and paint it to match with the rest of your trailer to make sure that it's protected from any kind of rust or corrosion. You can see that backing plate, it is welded in place. So it's going to stay attached to the fender itself, got kind of a ribbed design to the top of the fender. So it's going to have a nice structural stability. As far as the overall length, it's about 32 inches long from outer edge to outer edge, and then 15 inches tall from the base to the top or the apex.
And then it's about nine inches wide from front to back.It does have a one inch curved radius at the lip here. So it's a one inch radius for that. So it gives it a nice finished look. This does just come as a single fender, so you'll need one for either side. It weighs about nine pounds, it's made in the USA, and its covered by a one-year limited warranty.
And that's pretty much all there is to it for our look at the single axle trailer fender. I hope this has been helpful in deciding if this is the right one for you. We do have a lot of other options available though here at etrailer.com for all kinds of stuff for your trailer, so check them out. Thanks for watching.
Average Customer Rating: 4.8 out of 5 stars (2626 Customer Reviews)
9" Wide x 32" long x 15" tall. This sturdy, rounded fender has a durable backing plate that helps protect your trailer from debris. Ribbed, 16-gauge steel is built to last. Bolt or weld onto your trailer.
I used these steel fenders to replace aluminum fenders on my utility trailer after one had fallen off along the road somewhere. Prior to installing these I painted them with Krylon Fusion gloss hammered metal spray paint, which has held up well.
Very disappointed in the attachment of backing plates. Two fenders should be mirror image of each other. Apparently an alignment jig is not used in production. This makes for difficult and different mounting from each side.
Jenny N.
2/25/2022
I will have our customer service team reach out to you.
These are sturdy fenders! I taped off where the welds would be prior to painting and after mounting painted the welded areas. Look great on the trailer.
I bought two of these fenders to replace the fenders on my boat trailer that had rotted away. These fenders fit better than the original fenders that came with the boat. I bolted these fenders on after priming and painting them to match the trailer frame. I shopped around and etrailer had a great price compared to other vendors who were selling the exact same item. I have bought many items over the years from etrailer and have always been pleased with their products and quality.
Fast delivery. Product is high quality. This will replace the fender that blew off from a blowout.
I’m very satisfied with the overall outcome of ordering my trailer fenders from the online order process to there timely delivery. Of most importance was the quality of the fenders. They were made of heavy gauge sturdy steel. I’ve been closed some photos showing the final product after painting. I would definitely order again if necessary. Thanks trailer.
I really like the ribbed striations in the fender when I saw it in person. They add a little style to the part and they also add a little strength. I think they'll look very good when painted.
Four stars only because the fenders will need a little attention. The very ends need a little a few minutes of work to flatten them completely. That's a natural problem with rolled steel parts and it's easy enough to fix with a block of wood and a small hammer.
Most people wouldn't bother with this or might not consider it to be a problem at all but I'll square up the ends in just a few minutes before they get installed and painted.
The edges are sharp too. Again, a few minutes to dress them with a sander will get the sharp ends smoothed up. I've never seem a steel trailer fender that didn't need these two touch up items.
They're nice fenders but they aren't quite ready to paint as far as I'm concerned.
SO FAR EVERYTHING IS RUNNING GREAT...NO PROBLEMS.... GREAT PRODUCT.....
Arthur W.
6/4/2024
FENDERS ART GREAT
Very pleased with the product. Very quick delivery also. Thank you.
Michael
5/31/2024
Used on a motorcycle build and served the purpose. Good value for the need.
Backing plate is thinner gauge than the fender and only spot welded in 5 places. On one of the fenders one spot weld was already broken. Not a deal breaker as I kind of expected this. Just know that steps will have to be taken to reinforce the attachment of the backing plate to the fender, I will use rivets. Shipping was VERY fast and customer service is top notch. I will patronize etrailer in the future.
Horace C.
7/8/2023
I used these fenders on a tow dolly. I had to reinforce the backing plate to fender welds. Otherwise, fenders worked very well. I wouldnt attach the unit using the backing plate without strengthening.
these fenders are amazing and very well made, we adapted our brackets to fit the new steel fenders from plastic and they work great better then factory.
Impressive customer service! Quality products and fast shipping! I will continue to use etrailer!
The fender was well-made for the project that I used it for . The price was very reasonable and good customer service .
The staff at eTrailer were very attentive to my needs and provided alternatives to get a product to me on time. They're very helpful and I truly appreciate it.
Welds on the backing onto the fender were poor and delivered broken. I will have to reweld these myself.
Sierra K.
6/28/2022
I apologize for the way these arrived to you. I will have customer service reach out to you.
My dolly came with plastic fenders. A friend helped me maneuver the dolly and pushed on the plastic fender and broke it in two places. A tire blow out demolished the other fender. I purchased two of these fenders. They are made of a heavy steel and I am sure they will not need a replacement in the foreseeable future. Thank you for a prompt delivery.
Don
7/16/2023
We made several local trips less than 100 miles each and things were just fine. We then went to the finger lakes in NY State and hit some very bumpy roads on Route 81 in PA & NY. The fenders vibrated so much that the spot welds completely dislodged the fenders from the trailer and were only held in place by the wires for the lights. I stopped by a local hardware store, bought some channel and a hack saw and bolted on vertical and horizonal braces to both fenders. This made the rigidity needed and repainted the fenders. I have logged another 10,000 miles with no problems. You should recommend enforcement vertically and horizontally.
these are stout, although they aren’t the same size. one is abt a 5/8 of an inch longer than the other.
The fenders were a perfect addition for my UTV trailer. Great quality and easy to mount. The ribs look great too.
The item arrived without issue earlier than expected. The item was exactly as described (sometimes can be difficult to select the proper item without physically seeing it). The description was detailed and accurate. The item was of high quality and craftsmanship. I would certainly shop here again.
Very happy with the quality of this fen der
I recently ordered a new set of fenders and mounting brackets for my boat trailer. The fenders are very sturdy and the brackets are 1/4 in steel and quite rugged. This equipment is much stronger than original. I wasn't quite sure of sizes to order, but Cody O. was helpful and patient and walked me through the entire order. I am a happy camper.
Just what I needed
Great fenders for the price especially coming with the backs all ready installed.
THE FENDER IS AN EXCELLENT CHOICE FOR A REPLACEMENT. I UPGRADE JET SKI TRAILERS FROM 12" WHEELS TO 15" WHEELS AND THESE WORK PERFECTLY.
Arrived on delivery date when opened found 1 fender with the tac welds bad other than that they look good
Do you have a question about this Trailer Fender?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jo
12/31/2023
They are still holding up well.