Single Axle Trailer Fender for Enclosed Trailers - Cold Rolled Steel - 15" Wheels - Qty 1

See what our Experts say about this etrailer Trailer Fenders

• Replacement Fender For Drivers Side Of a 2018 Winnebago Winnie Drop 170K Travel Trailer
  While I have no way to lookup exactly what fenders are installed on your 2018 Winnebago Winnie Drop 170K I do see it has 14" wheels from the factory. This would mean the Fender # HP38VR would be the most likely candidate. But you will want to take measurements off your fender to verify the correct size. This fender is 9" Wide by 30" long and 13-1/4" tall. The Fender # HP56VR you found is for 15" wheels and is 9" Wide by 32" long and 15" tall. If your fender is different in size from either...
  view full answer...
• Strength of Steel Fender to Withstand 200 lb Utilizing as a Step
  The Single Axle Trailer Fender # HP56VR is made of 14 gauge steel and has one edge that is a 90 degree angle to weld it to your trailer and the other has a more rolled edge. The strength of the fender and ability to hold 200 lbs is based on your mounting. To stand on this fender, you will need to not only weld the edge but also as you stated add brackets which will support the weight. The steel is strong, but I recommend using brackets that can hold the weight on their own to ensure...
  view full answer...
• Replacement Fender Options For a Utility Trailer With 32" Between Fender Mounting Brackets
  The Single Axle Trailer Fender # HP56VR is 32" long at its widest portion of the fender. The fender is also 9" wide and 15" tall which you can compare to your current fenders to determine if this will work as a replacement. We do have the Fulton # F008564 plastic fenders which may work for your application. These fenders are 31-5/16" long at the widest point. They are also designed for a 14" wheel and tire but you can verify if they will fit with the 9-11/16" width and 12-3/4" height.
  view full answer...
  
• Availability of Fender Back Plate for 32 Inch Long Fender
  We offer 2 options for fender back plates. For a back plate closest to the measurements you provided, the Pre-Cut Fender Back # 10FB-32R measures 10-1/2 inches wide x 29-3/4 inches long. This fender back is designed to fit the etrailer brand Fender # HP56VR For a wider fender back, the # 12FB-32R measures 12 inches wide x 30 inches long. This fender back is also designed for the # HP56VR fender. Either of these fender backs will also work in a 10-3/4 inches wide x 32 inches long fender...
  view full answer...
• Availability of 33 Inch x 10 Inch x 18 Inch Trailer Fender
  The closest trailer fender we have available to the dimensions you mentioned is a Jeep Style Fender like the etrailer brand # HP96VR. This aluminum fender is 33 inches long, 10 inches wide and 17 inches tall. It is designed to fit with 13-15 inch wheels and can be installed as a bolt-on or weld-on application. For a standard fender, the closest option we have is the etrailer Single Axle Fender # HP56VR. This is a 16-gauge steel fender that is 32 inches long, 9 inches wide, and 15 inches...
  view full answer...
• Availability of 11 x 32 x 15 Inch Fenders for Single-AxleTrailer
  We can come pretty close to those measurements, assuming that the 10x32x15 you stated meant 11 inches wide, 32 inches long and 15 inches tall. The fender you were looking at would work for you, but the etrailer brand # HP56VR Steel Single Axle Trailer Fender, part # HP56VR measures 9 inches wide, 32 inches long and 15 inches tall and would come closer to the measurements you provided. These would work well for replacing your current fenders.
  view full answer...
• Pre-Cut Fender Back for etriler brand Trailer Fender
  The Pre-Cut Fender Back # 12FB-32R is made of 16 to 18 gauge material; so there are not some that are 16 gauge and some that are 18 gauge. This fender back, which is designed for etrailer brand Trailer Fender # HP56VR, has varying thicknesses between 0.048" to 0.057" which is why there is varying gauges listed.
  view full answer...
• Looking for Replacement Steel Fenders
  I have looked through the various steel trailer fenders we offer, and have not found any that match the exact measurements you provided. The closest fender I found was the CE Smith Pre-Galvanized Steel Fender, part # CE17701G. This fender measures 23-1/2 long by 7-1/16 inches wide by 6-1/2 inches tall (see photo).
  view full answer...
  
• How To Measure a Boat Trailer Fender Without Removing the Wheel
  I can understand that if your boat is loaded on the trailer, you don't want to remove one of the wheels to measure the fenders. Measuring a fender with the tire still mounted can be tricky, but it's not impossible. I've provided a diagram that should be helpful. You already know how to measure the width. To get the length it is easiest to tape a piece of stiff paper to the end of each fender edge that will protrude past the wheel. Then measure between the papers. For the height, you can...
  view full answer...
  
• Looking For Bewise Fender Part P464-025
  Hello Ed, thanks for reaching out. We may have a suitable replacement for the Bewise fender P464-025, but I was not able to find any specs for this fender online, so I will need a bit more information from you. Specifically, I will need to know the length, height and width of the fender. Also let me know the shape and if it is metal or plastic. If you can drop that info in the comments below, I am happy to look into it and see if we have anything similar.
  view full answer...
• Is the 16-Gauge Steel, Single-Axle Trailer Fender Sold in Pairs or Singles
  For the 16-Gauge Steel, Single-Axle Trailer Fender, # HP56VR, they are sold in quantities of 1. For a pair you would need to put a 2 in the quantity box.
  view full answer...
• Looking For Single Axle Fender Like Part HP36VR But Without The Backing Plate
  Hello Curtis. The Single Axle Trailer Fender # HP56VR is identical to the # HP36VR fender you mentioned only without the backing plate. The # HP56VR fender measures 9" wide x 32" long x 15" tall.
  view full answer...
• Can Metal Trailer Fender be Painted to Prevent Rust
  Trailer fender # HP56VR is made of raw steel and isn't really treated for corrosion resistance so painting it would definitely help to reduce the chance and spread of corrosion.
  view full answer...
• Fender Needed for a tire that is 27 Inches Tall and 12-1/4 Inches Wide
  The 16-Gauge Steel, Single-Axle Trailer Fender w/ Backing, item # HP36VR, that you mentioned would be large enough for the 27 inch tall dimension you gave, since most 15 inch tires are just over 27 inches tall, but the width of your tire would require that you get a much wider fender. We do not have a fender that is 12-1/4 inches wide but you could use the fender you mentioned, cut off the rolled lip on the outside of the fender, and then use a # HP56VR fender without back, cut off the...
  view full answer...
• Coupler and Tire Size on 50s Era Bantam Utility Trailer
  A trailer coupler will often be stamped to indicate the compatible ball size but on an older 50s-era trailer there's no guarantee this is there or that it is still visible after all those years. Hitch balls offered nowadays include five different sizes but a small utility trailer such as a 50s Bantam is likely to use one of the smallest sizes, either a 1-7/8-inch like # 19256 or perhaps a 50mm size like # 63912. Note that you also need to match the hitch ball shank size to the ball mount...
  view full answer...

Do you have a question about this Trailer Fender?