Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs

See what our Experts say about this CURT Trailer Hitch Ball Mount

• Trailer Hitch for 2007 Jeep Grand Cherokee SRT8 with Center-Positioned Dual Exhaust
  Yes, the Curt Class I Trailer Hitch Receiver # C11103 is a confirmed fit on the 2007 Jeep Grand Cherokee SRT8 with center-positioned dual exhaust. I confirmed compatibility with Curt's fit guide and also with one of their technicians. The written instructions and a helpful installation article are both linked to assist you. Tools required are listed in the instructions. If you plan to tow you will also need trailer wiring; use part # HM40975-11933 if you have the factory tow package or...
  view full answer...
• Recommended Parts to Tow a Small Trailer with a 2009 Buick LaCrosse
  We have everything that you need to get towing with your 2009 Buick LaCrosse. For a trailer hitch I recommend the 1-1/4" Class II Curt # C12239 because we have found the Curt trailer hitches typically have better welds and a thicker powder coat than other options. This contributes to a longer lifespan of the trailer hitch which in turn raises the quality of the hitch. Since you're needing to tow a smaller trailer you'll also need wiring to activate the trailer lights and for that I recommend...
  view full answer...
• Trailer Hitch Receiver for Towing With a 2015 Kia Cadenza
  I recommend the Curt Trailer Hitch Receiver # C12118 on your 2015 Kia Cadenza. This hitch has a tongue weight rating of 350lbs and 3,500lb trailer rating. You will want to ensure that you do not exceed the weight ratings given by the manufacturer for your vehicle. This will not require you to change your rear shocks. If your suspension is sagging you should check that the weight on the trailer is distributed properly across the trailer and you do not have to much tongue weight. You typically...
  view full answer...
• Trailer Hitch Receiver, Wiring Harness & Ball Mount for Towing a Trailer With a 2023 Buick Encore GX
  First you will need the Curt Trailer Hitch Receiver # C94UR for your 2023 Buick Encore GX. The Curt Drawbar # C45522 will then be paired with either a 1-7/8" # C40001 or 2" # C40018 hitch ball to match the coupler. I recommend then using the Master Lock Trailer Hitch Receiver Lock and Coupler Lock Set # 3794DAT to secure the ball mount to your Encore and have locks to secure the trailer to your Encore or while in storage. For the 4-way wiring you will need either the T-One Vehicle Wiring...
  view full answer...
• Curt Trailer Hitch for Chevrolet Malibu
  The Curt Trailer Hitch # C12051 is a confirmed fit for your 2009 Chevy Malibu. This hitch has a 300 Pound Tongue Weight Capacity and a 3500 Pound Towing Capacity with a 1-1/4 Inch Hitch opening. If you need a wiring harness for towing, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, # 118450. This is a confirmed fit wiring harness for the 2009 Chevrolet Malibu, excluding LTZ models. A good ball mount for this hitch is the Curt Drawbar # C45522.
  view full answer...
• What is Rise Dimension of Curt Ball Mount # C45522
  I apologize for any confusion but the Curt ball mount # C45522 has a rise of 3-1/8 inches.
  view full answer...
• Parts Needed to Tow a Yakima Rack and Roll Trailer with a 2013 Volvo C70
  You can certainly tow the Yakima Rack n Roll trailer, # Y08106 with the new hitch on your 2013 Volvo C70. But, you will first need to consult the vehicle owners manual for the capacities of the vehicle. Then check the trailer hitch for a sticker that lists its capacities. Whichever is lower, the vehicle or the trailer, is the rating you need to go by. The Yakima trailer weighs about 100 pounds and has a 250 pound capacity so the gross trailer weight would be a mere 350 pounds loaded to...
  view full answer...
• Is Bolt Leader Wire Included in Installation Kit for Curt Class I Trailer Hitch Receiver # C11282
  I might be a little biased but I think that our install videos are awesome. Written instructions get the job done but seeing someone complete the installation on video takes all of the guess work out of it for me. I'm glad to hear that you also feel that they are a great help. As for the bolt leader wire, yes it is included with the Curt Class I Trailer Hitch Receiver, # C11282, for your 2014 Chevrolet Cruze. This is a custom fit hitch and offers bolt-on installation with no drilling or...
  view full answer...
• Ball Mount Recommendation for 2005 Volvo V50 with Curt Trailer Hitch Installed
  For the Curt hitch part # C11438 that you have installed on your 2005 Volvo V50i has a recommended ball mount, part # C45522. This is a couple inches longer than the # C45561 you currently have so it would give you the clearance you'd need. For a 2 inch hitch ball you'd want the part # C40018 or for a 1-7/8 inch ball part # C40001.
  view full answer...
• How to Tow a Trailer with Brakes with a 1995 Chevrolet Impala SS
  The Curt Trailer Hitch Receiver part # C12009 is a confirmed fit for your 1995 Chevrolet Impala SS and will work well for you. In order to tow a trailer with brakes you will also need to use both the Curt T-Connector Vehicle Wiring Harness part # C55347 and the Universal Installation Kit for Trailer Brake Controllers part # ETBC7. If you need a brake controller I recommend the Curt TriFlex Trailer Brake Controller part # C24VV with the Universal Wiring Adapter part # C51515. The only other...
  view full answer...
• What Size Trailer Can Be Towed With The Draw-Tite Hitch # C12051 On A 2008 Chevrolet Malibu
  The Curt Class II 1-1/4 Inch Hitch, part # C12051, will fit a 2008 Chevrolet Malibu. It is a 1-1/4 inch hitch with a gross towing weight capacity of 3500 lbs. The 2008 Malibu will only have a towing capacity of 1000 lbs. So the vehicles towing capacity is what will limit you to how much you can tow. A towing systems capacity is limited by the lowest capacity in the whole system, in your case it is the vehicle at 1000 lbs. I am including a link to the installation instructions on the Curt...
  view full answer...
• Trailer Wiring Recommendation for Draw Tite Hitch for 2000 Ford Taurus
  We have trailer wiring for your 2000 Ford Taurus but the Draw Tite hitch part # 36313 does not come with it. For that you would then also want the part # C55375 which is a confirmed custom fit. The recommended ball mount is the part # C45522 and then for hitch balls you would want part # 19256 for a 1-7/8 inch ball or part # 19258 for a 2 inch ball.
  view full answer...
• Recommended Trailer Hitch Receiver, Ball Mount and Wiring For a 2013 Chrysler 200
  With the Curt Trailer Hitch Receiver # C11133 on your 2013 Chrysler 200, Curt recommends using one of the following ball mounts. First is the Curt Class II Drawbar # C45522 with either a 1-7/8" Ball # C40001 or 2" Ball # C40018. Or you can choose one of their Euro Style Ball Mounts with a 1-7/8" # C45591 or 2" # C45592 ball. Whichever you choose you will need a Curt Hitch Pin and Clip # F-4 to secure it in your receiver. You will also need a Vehicle Wiring Harness # C56211 to control...
  view full answer...
• Will a Class II Drawbar Fit Into the Class I Curt Hitch # C11080
  Curt states that Drawbar, # C45522, is the ball mount designed for use with Curt Trailer Hitch Receiver, # C11080. Although the Curt Drawbar, # C45025, will most likely fit in your hitch, it was not designed for use with this particular hitch. If failure occurs when using this drawbar, Curt may void any warranty on the hitch. As for using a Class II drawbar in a Class I trailer hitch, most Class I trailer hitches have a stop built into them so a Class II drawbar can not be used. This...
  view full answer...
• Recommended Ball Mount and Hitch Ball for a 2012 Subaru Outback Wagon with 1-1/4 inch Receiver
  When measuring to see if you need a ball mount with a Rise or Drop you will want to make sure that your 2012 Subaru Outback Wagon is level and you will want to measure from the ground to the top of the trailer hitch receiver. For your trailer you will want to park it on level ground and measure from the ground to the bottom of the coupler. The difference between these 2 numbers will determine if you need a ball mount with a Rise or Drop. I have attached a helpful article and a picture to...
  view full answer...
  
• Which Trailer Hitch and Wiring Kit Fits 1979 Buick Electra
  For your 1979 Buick Electra the Curt hitch part # C12009 is actually the correct fit and not the one you mentioned as it fits other vehicles that are much different. Then for a trailer wiring kit the Curt part # C59236 is the best option for you. For a ball mount then the part # C45522 is the correct one for the hitch mentioned. For hitch balls you'd want the part # C40018 for a 2 inch ball or part # C40001 for a 1-7/8 inch ball.
  view full answer...
• Availability of Hitch for 2007 Toyota Solara Sport Convertible
  According to Curt, the Class II hitch you referenced, part # C12110 will indeed fit your 2007 Toyota Solara Convertible Sport model. If you were planning on using the hitch for towing, you will also need the following parts to complete your towing system: • Wiring harness with trailer connector, part # C59236 • Ball mount, part # C45522 • Pin and Clip # F-4 • 1-7/8 inch trailer ball, part # 19256 • 2 inch trailer ball, part # 19258 • Locking hitch pin, part # e98879 For installation...
  view full answer...
• Does Exhaust have to be Lowered to Install Trailer Hitch on 2007 Saturn Aura XR with Dual Exhaust
  The Curt trailer hitch # C12051 fits all models of the 2007 Saturn Aura including your XR with dual exhaust. Temporarily lowering the exhaust is not required but will make installation of the hitch a whole lot easier. I have included a link to the installation instructions for you. If you plan on doing any towing with the hitch the recommended ball mount is # C45522 with pin and clip # F-4. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And to add a 4-Way flat connector...
  view full answer...
• Trailer Hitch And Wiring Recommendation For 2012 Chevrolet Cruze
  From the research I found, the 2012 Chevrolet Cruze has a towing capacity of 1,000 lbs. The Curt Hitch, part # C11282, will work for you. This is a Class l hitch and has a 1-1/4 inch receiver opening. All non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps like part # 18050. Failure to properly support these loads will void your hitch warranty from Curt. To tow a trailer you will need ball mount # C45522, pin and clip # F-4, and a...
  view full answer...
• Recommended Trailer Hitch for 2001 Ford Taurus SE
  I do have a trailer hitch recommendation for you 2001 Ford Taurus, however since the two models you're referring to are two different generations the hitch you have on the 92 will not fit. I suggest, instead, the Curt Class II # C12232. It's custom fit for your Taurus and doesn't require any drilling to install. For a new wiring harness, you will need the Curt # C55375. And a ball mount # C45522. Hitch ball # 19258 will fit the mount. I've included videos of the items for you to...
  view full answer...
• Trailer Hitch Recommendation for a 2002 Ford Taurus Wagon
  For a hitch for your 2002 Ford Taurus Wagon you would want the Curt Hitch part # C12232 as it has been confirmed to fit your vehicle. You would just need a ballmount like the # C45522 and a ball like # 19256 for a 1-7/8 inch diameter or # 19258 for a 2 inch diameter and trailer wiring to complete the towing set up. For trailer wiring, use # 119178KIT. I have included a link to the installation details for the wiring for you.
  view full answer...
• What is the Towing Capacity of a 2009 Chevy Malibu
  I checked an online copy of the owners manual for the 2009 Chevy Malibu and the vehicle is rated for 1,000 pounds. I cannot recommend towing anything heavier than that. I would take what you have been told with a grain of salt. What you should do is follow the procedures specified in the owners manual. Paddle shifters on an automatic rarely work like you would want them to. Often times they result in a hard shift or delayed shift which can negatively affect ride quality plus it is one...
  view full answer...
• Ball Mount Recommendation for 2012 Chevrolet Cruze With 1-1/4 Inch Trailer Hitch
  We have a couple different style ball mounts that will work with the hitch on your Cruze. For a standard ball mount I recommend the Curt, part # C45522. This ball mount has a 3-7/8 inch rise to help provide a bit more ground clearance. For a 1-7/8 inch hitch ball I recommend part # C40001, and for a 2-inch ball I recommend part # C40018. If you like the looks of the Euro ball mounts I recommend part # C45592 that comes with a 2-inch hitch ball and I recommend part # C45591 for a 1-7/8...
  view full answer...
• What is Rise of Curt Ball Mount # C45522
  Actually we've had this come up a few times. We've had three different people measure this ball mount and we've all come up with 3-7/8 inches of rise despite what Curt's site says. If you need a 3-7/8 inch rise ball mount this one WILL work great for you.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?