Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs

See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Compatability of Bike Rack Part # 63120 and Draw-Tite Class 1 Hitch part # 24807
  The hitch you have, Draw-Tite part # 24807 is a Class 1 hitch. There are two different classes of 1-1/4 inch hitches, Class 1 and 2. Class 2 drawbars and bike racks will not fit Class 1 hitches. Class 1 hitches have a lower rating than Class 2 and to prevent people from accidentally exceeding capacities the manufacturers make it so that heavier Class 2 accessories are too long to be used in Class 1 hitches. But you can still use Class 1 accessories in Class 2 hitches. The bike rack you...
  view full answer...
• Will Sportframe Drawbar # 3594 Fit Kubata RTV Receiver
  I pulled a Sportframe Drawbar, part # 3594, from our warehouse and took a measurement for you. As the attached photo shows the distance from the end of the shank that inserts in the receiver on your Kubata RTV to the center of the hitch pin hole is 1-1/2 inches. This drawbar is designed to fit 1-1/4 inch receivers. You mentioned that you have 2 inches before it hits the axle. The best way to see if this will work is to take a ruler and insert it in the receiver on your RTV. If you have...
  view full answer...
  
• How to Determine Where Ball Mount Platform for 3594 Will End Up When Installed on 1998 Buick Regal
  What you will have to do is measure from the top of your hitch opening up 4 inches and then from that point measure down to the ground to know where the platform will end up. We haven't had the chance to get that measurement on 1998 Buick Regal yet.
  view full answer...
• How to Pick Out Correct Ball Mount for 2015 Ford F-150
  I attached an FAQ that details how to pick out the correct ball mount. Picking out the correct ball mount will allow your trailer to sit as level as possible. Basically you will first measure the height from the ground to the top of the receiver opening on the hitch while on level ground. Next, you will measure the coupler height from the ground to the bottom of the trailer coupler when the trailer is on level ground. Next, you will need to compute the difference. If the hitch height is...
  view full answer...
• Pin Hole to Hitch Opening Distance on 2 inch and 1-1/4 inch Hitches
  Typically the distance from the center of the hitch pin hole on a 1-1/4 inch hitch to the face of the opening on the hitch measures 2 inches whereas on a 2 inch hitch the distance is 2-1/2 inches.
  view full answer...
• How to Measure to Determine How Much Drop Is Needed for a Ball Mount
  Thanks for the measurements you gave. To determine drop needed you need to measure from the top of the hitch opening to the ground and from the bottom of the coupler lip to the ground. Those two numbers compared is the amount of drop you'd need. I attached a help article that covers this as well. Let me know what you come up with and I can get you the best solution. Also, what size ball do you need?
  view full answer...
• Does Suspension Sag Factor When Picking Out Correct Rise/Drop Ball Mount
  Sounds like you are asking about how to pick out a ball mount that allows the trailer to sit as level as possible. Ideally you go with the rise/drop that allows the trailer to sit totally level with it loaded. Since significant sag isn't always present it may not have been addressed directly enough in our help article on the subject. But when I recommend a ball mount for someone I typically will recommend going with the drop that's a little higher than measured for this reason. But suspension...
  view full answer...
• Lock Pin Hole Measurement for Class I Hitch
  The distance from the center of the hitch pin hole to the end of the drawbar is 1-9/16 inches. This is a Class I drawbar. Class II drawbars will not fit in the Class I hitch and have a distance of approximately 2 inches from the center of the hitch pin hole to the end of the drawbar.
  view full answer...
• Dimensions of the Ball Mount Included with the Hidden Hitch part # 60280
  The ball mount that is included with the Hidden Hitch part # 60280 (no longer available) that you referenced is the Sportframe Draw Tite Ball mount part # 3594 which has a 4 inch rise and measures 10 inches from the center of the pin hole to the center of the ball hole. I attached a review video for you to check out also.
  view full answer...
• Ball Mount Will Not Fit Into Draw-Tite Class I Hitch, # 24794, On Nissan Sentra
  It sounds like the ball mount you have might be a Class II ball mount. The 1-1/4 inch size receivers come in two classes, Class I which is rated for 2,000 lbs. towing and 200 lb. tongue weight and Class II which is rated for 3,500 lbs. towing and 350 lbs. tongue weight. To keep a user from overloading a Class I hitch, Class II hitch accessories, such as ball mounts and several bike racks and cargo carriers, are designed to not fit. Manufacturers accomplish this by placing a stopper in...
  view full answer...
• Specifications for Ball Mount # 3594 Included with Trailer Hitch # 60872 for a 2008 Hyundai Elantra
  The ball mount that comes with the Hidden Hitch Trailer Hitch, # 60872 (no longer available), is Sportframe Drawbar, # 3594. This Class I ball mount is designed for a 1-1/4 inch receiver. It uses a ball with a 3/4 inch diameter shank. It is 10 inches long from the center of the hitch pin hole to the center of the ball hole. It will provide a 4 inch rise from the top of the trailer hitch receiver tube. This ball mount should only be used in the rise position. It is rated for up to 200 pounds...
  view full answer...
• Why do Some Ball Mounts Have a Drop and Rise and Others Only have a Rise
  Some ball mounts, generally Class I and Class II ball mounts, are designed by the manufacturer for use in the rise position only. These ball mount designs are intended for use with vehicles that require a rise only and would be too low to the ground to ever need a lower ball mount. Ball mounts listed with a rise only should not be used in the lowered position because the manufacturer has not tested them for use in that position. Some Class I and Class II ball mounts, like item # 3592,...
  view full answer...
• Which is Correct Ball Mount for 1997 Chevrolet Lumina w/ Draw-Tite Trailer Hitch # 24628
  The recommended ball mount to use on a 1997 Chevrolet Lumina with the Draw-Tite Trailer Hitch 24628 (DISCONGTINUED) is the Draw-Tite Ball Mount, part # 3592. The ball mount that you referenced, part # 3594 has too much of a rise and is not recommended by Draw-Tite to be used on the Chevrolet Lumina. With Class I and II hitches, the ball mount recommended by the hitch manufacturer must be used, not doing so will void the hitch warranty. I have linked an FAQ on hitch ball mounts.
  view full answer...
• Towing a Trailer with 2014 Mustang GT vs 1999 Honda Civic Coupe
  I did some checking in the the owners manuals for both the 2014 Ford Mustang GT and the 1999 Honda Civic Coupe for you. The owner's manual for the 1999 Civic Coupe instructs that the vehicle is not designed for and should not be used to tow a trailer. I was able to find the 3.7L and 5.0L Mustang have a maximum trailer weight capacity of 1,000 pounds. Per the owner's manual, the Shelby GT should not be used to tow a trailer. The biggest concern in towing with the Mustang will be ground...
  view full answer...
• Why Are Hitch Adapters for 1-1/4 inch Hitch Not to Be Towed With
  Hitch adapters create quite a bit of leverage and movement in the hitches they are installed in. Since 1-1/4 inch hitches are very low in capacity already it's not a good idea to use an adapter like the part # HTAD to tow with. You'd just need to get a 1-1/4 inch ball mount to fit the hitch and there'd be no need for an adapter like the # 3594.
  view full answer...
• Dimensions of Hitch Pin Hole and Weld Stop On Class I Trailer Hitch Receivers
  Class I trailer hitch receivers like # 24847 have a distance of about 1-5/8 inches from the center of the hitch pin hole to the welded stop in the back of the hitch receiver tube. Class I ball mounts like # 3594 normally are about 1-9/16 inches from the center of the hitch pin hole to the back to allow fit. The Class I hitches have this welded stop to ensure only Class I rated accessories will fit so you don't overload your hitch capacity. The Class II trailer hitches do not have the...
  view full answer...
  
• Will the Draw-Tite 3594 Get Me Close to 16 of Rise if My Hitch is 11 1/2 Off the Ground?
  From the measurement you provided, the Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs # 3594 will definitely get you as close to level as possible. The Draw-Tite 1-7/8" Hitch Ball # 19256 would then complete the set up.
  view full answer...
  
• Ball Mount Recommendation that is 4 inches Shorter than the Sportframe Ball Mount part # 3594
  I believe the closest thing we have to the Sportframe Drawbar part # 3594 that you referenced that is 4 inches shorter would be the Curt Class I Drawbar # C45027. The length of this ball mount from the center of the hitch pin hole to the ball hole is 6-1/4 inches and it has a rise of 2-5/8 inches. Basically this ball mount is 4 inches shorter than the ball mount you referenced but its rise is about 1-1/2 inches lower.
  view full answer...
• How to Measure Ball Mount Rise for Draw-Tite Sportframe Ball Mount # 3594 on a 2002 Buick Regal
  Ball mount rise, or drop, is determined by inserting the ball mount into the hitch on your vehicle and measuring from the top of the hitch opening to the top of the ball mount platform. I added a photo showing how the rise and length would be measured on the Draw-Tite Ball Mount # 3594. We also have an informational article that explains how to choose the correct ball mount for your application. All Class I and Class II trailer hitches are tested and rated with the specific ball mount...
  view full answer...
  
• Recommended Ball Mount Draw Bar For 1-1/4 Inch Trailer Hitch Receiver With 4 Inch Rise
  The 3/4 inch diameter is a typical size for the 1-1/4 inch hitch receivers. Normally the 1 inch diameter hitch ball is used on a 2 inch receiver ball mount. I have linked the page to the ballmounts that are available for your 4 inch rise and 1-1/4 inch receiver. I recommend the Sportframe Drawbar 4" Rise 2000 Kit # 3594 which has a 10 inch length from center of hitch pin hole to center of ball with 4 inch rise. I recommend the 2 inch hitch ball # 19258 or the 1-7/8 inch hitch ball...
  view full answer...
• Dimensions Of Draw-Tite Sportframe Ball Mount # 3594
  The measurement from the center of the pin hole on the Draw-Tite Sportframe Ball Mount # 3594 to the center of the hitch ball hole is 10 inches. The measurement from the pin hole center to the forward edge of this mount is 1-9/16 inches. This ball mount is compatible with Class I hitches with a weight capacity of 2000 lbs and a tongue weight capacity of 200 lbs. I have provided a link to a video review of this item. If you need a hitch ball for this item, you might be interested in the...
  view full answer...
• What Is The Highest Capacity Trailer Hitch Available For A 2021 Mazda 3 Hatchback?
  For your 2021 Mazda 3 Hatchback, I recommend going with the Curt # C98BR. At the time of this writing, this is actually the only hitch we have that is confirmed for your vehicle, but due to its hidden design, it is one that I do like. With this being a Class I hitch, it will have a 1-1/4" receiver and is rated up to 2,000 pounds towing and 200 pounds of tongue weight, though you will need to check your owner's manual for your vehicle's capacities. To complete a towing set up, you will...
  view full answer...
  
• Parts Needed to Tow a Trailer with the 2011 Ford Fusion
  You can pull a trailer with any class of trailer hitch, you just need to be under the weight capacity of either the hitch or vehicle, whichever is lower. Therefore, for your 2011 Ford Fusion I recommend the Draw-Tite Sportframe Trailer Hitch Receiver part # 24865 which has a 200 lb tongue weight and 2,000 lb gross trailer weight rating. Please keep in mind that the owner's manual does not recommend towing a trailer with the vehicle so they do not list any towing capacity. In addition...
  view full answer...
• Recommended Trailer Hitch and Ball Mount for a 2009 Chevy HHR
  The trailer hitch I recommend is the Draw-Tite Class I # 24756 and Draw-Tite ball mount # 3594 because the top of the receiver to the ground is 10-1/4 inches and the ball mount will give you a 4-inch rise. As a result, giving you a 14-1/4 inch ground clearance and stay above the 13-1/2 inches. The weight will bring the clearance down a tad from the 14-1/4 inch clearance which will keep your trailer more level. The wiring for your 2009 Chevy HHR is # 118407 and 1-7/8 hitch ball is # 19256.
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?