Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
(2084 reviews)
Price: $39.45
In Stock
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
Item # 36065
Retail:$51.07
Our Price: $39.45
You Save: 23%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (2084)
- Q & A (0)
- Photos
Draw-Tite Trailer Hitch Ball Mount - 36065
- Fits 1-1/4 Inch Hitch
- Fixed Ball Mount
- Rise - 5 Inch
- No Ball
- 3500 lbs GTW
- Class II
- Draw-Tite
- Steel Shank - Gloss Black
- 3/4 Inch Ball Hole Diameter
Sturdy steel ball mount with solid shank measures 10" from center of hitch pin hole to center of ball hole. Drawbar is Class II compatible only. Powder coat finish over a-coat base provides excellent rust protection.
Features:
- Ball mount lets you hook up your trailer to your tow vehicle
- Shank slides into your vehicle's hitch receiver
- Ball platform provides mounting point for hitch ball (sold separately)
- Drawbar can be used in rise position only
- Sturdy steel construction with solid shank
- Black powder coat finish covers a-coat base for superior rust protection
- Hitch pin and clip included - hitch lock sold separately
Specs:
- Application: 1-1/4" x 1-1/4" trailer hitch receivers
- Class II compatible only
- Gross towing weight: 3,500 lbs
- Tongue weight: 300 lbs
- Length: 10" from center of hitch pin hole to center of ball hole
- Rise: 5" from top of inside of hitch opening
- Ball hole diameter: 3/4"
- Pin hole diameter: 1/2"
- Limited lifetime warranty
36065 Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
Replaces 90009
California residents: click here
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Did not fit
Customer Reviews
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs - 36065
Average Customer Rating: 4.8 out of 5 stars (2084 Customer Reviews)
Sturdy steel ball mount with solid shank measures 10" from center of hitch pin hole to center of ball hole. Drawbar is Class II compatible only. Powder coat finish over a-coat base provides excellent rust protection.by: Ronald06/01/2023
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
by: Richard10/19/2023
Tha drawBar is well made and fits perfectly on my 2005 Honda civic. It also clears the rear bumper so there is no rubbing damage to vehicle paint. I added a 2inch ball and the height is approximately 20 inch which is great for towing small trailers. If you have a 2001-2005 Honda civic this is the drawBar for you.
by: Toby06/30/2013
I've got a lowered 1995 VW Jetta with a 1.25" receiver. I had to use a 6" extension along with a long, straight drawbar so any steep incline had me going at an angle and even then I would sometimes scrape. Some one had this drawbar on their Jetta and it looked good. With the measurements provided on this site I determined it would sit far enough away from my bumper and elevate the ball so my trailer wouldn't be angled down so much. Very glad I ordered this unit, it fits the car and works perfectly! Much better than my previous fix.
by: David04/02/2022
Had to replace hitch & draw bar on my 2011 Camaro. This was exactly what I needed, delivery was fast & the price was good
David
4/3/2023
This was a replacement draw bar. It works like the original. It was shipped fast, price was good, & works perfectly. Thanks again, good job!
by: Buddy10/12/2023
Nice Paint Job, Ball was ez to install, Come with Pin, Nice.
by: Doug06/24/2023
Alex was extremely helpful and got exactly what was needed for the older model Volvo , I purchased 4 pieces and it fit perfectly. Have used it repeatedly and not had any issues
by: Robert 08/26/2023
I really like dealing with the people. They have helped me find the right stuff, made it easy on me.
by: Lawrence R.07/25/2017
As you can see your product was 100% perfect for getting my one legged friend and former Marine back to enjoying the open road. He's allowed to easily load his wheelchair by himself and with the added strength and length it gives him great stability and ease.
Thanks again definitely recommend etrailer to all I run into, the price also greatly appreciated.
by: Mark 09/29/2023
Fast service, looks great.
by: Brett07/18/2020
I have a 2016 300c awd. This riser bar was the perfect height to keep my boat trailer level with the ground.
by: John 12/15/2022
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
by: Gail 04/29/2021
The drawbar works great! It allowed us to pull our inflatable boat trailer at the correct height and distance from our Camry. Would recommend to a friend!
Gail
4/30/2022
We towed the inflatable using the tow bar over 3000 miles with no issues. Great product!
by: Gerald10/28/2022
Delivery was delayed from the manufacturer. Further delay was encountered when shipment was mis directed to Sheboygan.
When it finally arrived there was a hole in the box and the receiver was poking out.
Lucky the paint wasn't damaged.
The part is what I ordered.
by: Joel 05/15/2023
Very solid.
by: Mike M08/19/2016
The hitch was easy to install, and etrailer easily added the drawbar, ball, and wiring that I needed. Overall this was a fast, inexpensive solution.
Mike M.
3/12/2017
Thank you for following up. Other than a few bumps getting out of driveways, the hitch has been satisfactory. The Aura has such a low-riding bumper!*
by: Jessica 09/10/2022
Solid steel, really nicely made. Delivery was swift as well 2 days faster than promised.
I'm highly recommending etrailer.com they've been fantastic!
by: Alben05/14/2023
right amount of rise
by: Regis01/25/2016
There is, what seems to be an excessive amount of play between this drawbar and my hitch resulting in a lot of rattling. I will investigate using shims of some kind to alleviate the matter.
Regis
1/24/2017
Using still shims has helped, not ideal but no other solution short of welding.
by: Caleb05/21/2019
This hitch has been great to use with my VW Golf. It had accurate measurements on the description. When it came it fit with my car and trailer exactly how I thought it was going to. It is also solid metal and much more durable than what a little car needs. This hitch is definitely not the weak link in my car/trailer setup. It is a hitch I’d recommend to my friends in a similar situation. If you have a small car, this is a great hitch.
by: Brandon 07/22/2021
I've used this multiple times now along with the trailer hitch from etrailer that my friend and I installed ourselves. It works great even after a year. I would highly recommend an additional purchase of a locking pin that can be used with your car ignition key to keep your cargo safe.
by: Chris W.07/29/2011
Ordered the hitch, wiring harness and drawbar for my 2011 Malibu. E-trailer was very good over all in the transaction, they communicated well, got the order out very quick and upgraded my shipping so I got the parts faster and the directions and video clips on their site were great and I had everything installed in just over 2 hours by myself - although a second person would have helped. the bolt wires they included with the hitch made getting the bolts through the frame so easy :) Have already used the hitch with a trailer and it worked great. I would definitely use them again!
by: Oleg 06/04/2021
Great for Saturn Aura and Chevrolet Mal ibu.
Oleg
6/5/2022
No problem!
by: Peter 09/10/2022
Boxed perfectly... shipped great...
Installation was a breeze.. everything as stated. Thank you
by: Emmanuel 09/15/2020
I bought for my 2020 Toyota Camry which sits low to the ground and needs at least 5" rise. The Drawbar hitch ball mount arrived as described and high quality as expected. I am very satisfied with my purchase. Highly recommend if you have a car and need a 5" rise for your trailer coupler. I am extremely confident and happy customer.
by: Detrick08/03/2012
This doesn't quite fit my hitch. When the drawbar is inserted fully, the hole for the hitchpin is about 1/4" too far out, and can't be inserted. I'll have to cut the drawbar down a bit to get everything to fit properly. This is surprising to me because I have another drawbar by the same manufacturer, but with less rise, and it fits perfectly.
Also, a ball with a medium shank is *not* necessary. A short shank should fit just fine. You can see how much extra shank there is in the picture.
25
2081
Show More Reviews
See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount
- What is the Finish on the Class II Drawbar 5 Inch Rise Kit, 36065The finish on the Class II Drawbar 5 inch Rise (Kit), # 36065, is a black powder coat.
view full answer... - Recommended Draw Bar with 5 Inch Rise for 1994 Dodge Caravan with Class II ReceiverIf your Caravan has a Class II receiver the Class II Draw Bar with 5 inch rise, part # 36065 will work just fine for you. Keep in mind that this draw bar accepts a trailer ball with a 3/4 inch shank. The draw bar is rated for a maximum of 3500 lbs towing weight and 300 lbs of tongue weight.
view full answer... - What is the recommended Draw Bar for a 1999 Cadillac DeVilleThe manufacturer recommended drawbar for your Cadillac DeVille is part number 36063 which has a 3-1/8 inch rise and 11-3/4 inch long distance between the center of the hitch pin hole and the center of the ball mount hole. When towing with a class II trailer hitch, the ball mount that is recommended by the manufacturer should be used. All class II trailer hitches are tested and rated with the specific ball mount for that hitch. Using a ball mount that is not recommended by the manufacturer...
view full answer... - Ball Mount for Trailer Hitch 24890 on a 2015 Dodge Dart Towing Detail K2 Trailer K2MMT4X6When we installed Draw-Tite trailer hitch # 24890 on a 2015 Dodge Dart the distance from the ground to the top of the receiver opening was 9-1/2 inches, see video link. That means you will need a ball mount with a rise of 6-1/2 inches to get to a height of 16 inches. We can get you close with ball mount # 36065 which has a 5 inch rise. For a compatible ball use # 19258.
view full answer... - Can The Draw-Tite Ball Mount, # 36065, Be Turned Over And Used As A Drop On a Mercury MountaineerA 1-1/4 inch hitch receiver is either a Class I or Class II hitch. All Class I and Class II can only use the ball mounts that are recommended for that vehicle. For safety reasons, if you have to change the rise or drop from the recommended ball mount, then the manufacturer does not recommend to tow that trailer with the Class I or Class II hitch on your vehicle. We have Class III hitches available for Mercury Mountaineers that will bolt on underneath the OEM 1-1/4 hitch. The Class III...
view full answer... - Can Hitch Ball with Short Shank be Used with 1-1/4 Inch Ball Mount 36065Yes, you could use a short shank. For a 2 inch ball with short shank that fits ball mount # 36065 you can use # 19258. And for a 1-7/8 inch ball use # 19256.
view full answer... - Hitch Recommendation and Comparison for a 2006 Mitsubishi EclipseWe do not have any hitches to fit your 2006 Mitsubishi Eclipse. If you were wanting a hitch to carry bikes, you could instead use a trunk mounted bike rack. We have the Hollywood Racks Express 3 Bike Carrier - Fixed Arms - Trunk Mount # HRE3 which you can use to carry 1-3 bikes. Please take into account that this rack will not work with spoilers. Check out the attached video to see it in action.
view full answer... - Using a 36078 Class II Drop Drawbar as a Rise Instead of a DropThe drawbar you mentioned is not intended to be used in the rise position and would only create a 3-1/2 inch rise. We do carry a 5 inch and a 3-1/8 inch rise drawbar (see links below) that will fit the Class II hitch. These drawbars all have a tongue weight capacity of 300 lbs and a towing capacity of 3500 lbs. Keep in mind that if you need a significantly higher or lower drawbar to tow (you are not able to use the manufacturer's recommended drawbar for the hitch), you will void the manufacturer's...
view full answer... - Trailer Hitch Fit and Towing Capacity for 2009 Pontiac G6 The Draw-Tite Class II hitch # 36426 is a confirmed fit for your 2009 Pontiac G6 and the hitch itself offers a maximum towing capacity of 3500-lbs. If your trailer has a 2K-rated axle then the hitch will have plenty of capacity to tow it, but you'll also want to check the G9 owner's manual since the car itself may have a different towing capacity than the hitch. The lower-rated item determines overall capacity. A hitch installation video is linked for you. Towing also requires a ball,...
view full answer... - Can a Class II Ball Mount be Used with a Class I Trailer Hitch on a 2006 Mitsubishi Eclipse GTWith a Class I trailer hitch on your 2006 Mitsubishi Eclipse, you should only use the ball mount that is recommended for use with the trailer hitch. Another problem is that the ball mount that you have referenced is a Class II accessory. Class II items are designed so that they will not fit in a Class I trailer hitch. You could use Sportframe Drawbar, # 3592, which will give you a 2-1/8 inch rise or # C45016, which will give you a 2-5/8 inch rise.
view full answer... - What is the Correct Ball Mount for a 2005 Toyota CamryBecause all of the trailer hitches for the 2005 Toyota Camry are Class II hitches, see link, you must use the ball mount specified by the trailer hitch manufacturer. Using a different ball mount voids the warranty because only the recommended ball mount has been tested and approved for each respective trailer hitch. For a Draw-Tite or Hidden Hitch trailer hitch, use # 36061. It has a 3-1/8 inch rise measures from the top of the receiver opening on the hitch. For the Curt hitch, the correct...
view full answer... - Class II Ball Mount with 1-1/4" Shank Needed that has a 5" or 6" Rise/DropI am attaching a link to all of our Class II ball mounts that fit a 1-1/4" receiver opening. Since adjustable ball mounts are geared towards vehicles that tow regularly, like pickups, they don't make any that fit a 1-1/4" receiver. Among the linked ball mounts we have the Draw-Tite # 36078 which has a 5" drop or the Draw-Tite # 36065 which has a 5" rise, both of which are rated for 3,500 lbs. Either of these ball mounts are compatible with the 1-7/8" Hitch Ball # 19256 rated at 2,000...
view full answer... - Drawbar for Trailer Hitch of 2005 Pontiac G6For the Class II hitches that fit your 2005 Pontiac G6 like the Draw Tite part # 36426 the drawbar/ball mount you'd want would be the # 36065. Then for a hitch ball you'd want the part # 19258 for a 2 inch ball or part # 19256 for a 1-7/8 inch hitch ball.
view full answer... - Does Anything But a Class I Trailer Hitch Fit 2013 Ford Focus ST HatchbackThere is one trailer hitch fit for a 2013 Ford Focus ST hatchback, the Curt Trailer Hitch # C11431 which is a Class I hitch and not Class II, as you noted. This means you would need to use accessories that are Class I compatible and have a 1-1/4 inch shank, such as the Thule EasyFold XT 2 Bike Platform Rack # TH903202. If you are asking the reason behind the decisions as to why only a Class I hitch is available for a '13 Focus ST hatchback, unfortunately that is not something I can give...
view full answer... - What is the Recommended Ball Mount for a 2005 Toyota Sienna with a 1-1/4 Inch Trailer HitchFor a Class I or II trailer hitch with a 1-1/4 inch trailer hitch, you must use the ball mount that is recommended by the trailer hitch manufacturer. The reason is that the hitch has been tested with a specific ball mount and it is deemed to be the safest and best option for that vehicle and hitch combination. The only 1-1/4 inch hitch we carry for your 2005 Toyota Sienna is # C12065. The correct ball mount for this hitch is # C45016, and it must be used in the rise position only. It has...
view full answer... - Recommended Ball Mount for a 2006 Toyota Sienna Ball With a Class II Trailer HitchThe recommended ball mount for your 2006 Toyota Sienna would have a 2-5/8 inch rise, like Curt ball mount # C45016. This would put the hitch ball at the most common trailer height, but to ensure it will work with your particular setup, I would recommend taking a couple simple measurements. First, measure from the ground to the top of your class II hitch opening. Then, with your trailer level, measure from the ground to the flat bottom of the trailer coupler. The difference between these...
view full answer... - What Size Ball Hole do Ball Mounts that Fit 1-1/4 inch Hitches HaveAll of the Class II ball mounts out there have a 3/4 inch diameter ball hole. It might be the best solution for you to replace the ball you have with one that will fit that ball hole size like what comes with the # 36065 that you mentioned. For a 2 inch ball you'd need the # C40018 or for a 1-7/8 inch ball # C40001 and you'd be set.
view full answer... - Ball Mount and Wiring Recommendation for Draw Tite Hitch that Fits 2005 Pontiac G6The Draw Tite hitch part # 36426 that you referenced does not come with a ball mount but we do offer the recommended ball mount from Draw Tite as # 36065. This will give you a 5 inch rise. For hitch balls you'd want the part # 19258 for a 2 inch ball or part # 19256 for a 1-7/8 inch ball. If you are unsure what size ball you need check the coupler on your trailer as it will be listed there. You'll also need trailer wiring to activate the lights of the trailer you plan to tow. For that...
view full answer... - Hitch and Trailer Recommendation for a 2011 Chevy HHRThe only way you could transport a 500 handicap scooter with your 2011 Chevy HHR would be for you to install a hitch like part # 24756 and then use a small trailer. A cargo carrier setup wouldn't work because your vehicle wouldn't have the tongue weight rating to suspend the weight of your 500 lb wheel chair off the ground unsupported. To complete your towing setup you would also want a ball mount, the # 118407 for trailer wiring, # 19256 for a 1-7/8 inch hitch ball, and # 19258 for a...
view full answer... - Recommended Trailer Hitch and Wiring for 2010 Hyundai AccentStarting with the trailer hitch for your 2010 Hyundai Accent, I do recommend the Draw-Tite Class I Sport Frame Receiver Hitch # 24795 referenced in your question. This is a Class I hitch that will provide a towing weight capacity of 2,000 pounds. I like this model over the Curt alternative also confirmed to fit your vehicle because unlike Curt, Draw-Tite does not require the use of stabilizing straps like # 18050 with non-trailer loads such as bike racks and cargo carriers. After your move...
view full answer... - Trailer Hitch Recommendation for a 2004 Buick RegalI think you meant to type 2004 Buick Regal since there was no 2006 Regal. For a hitch to fit a 2004 Regal you would want the Curt part # C12225 which has been confirmed as a fit. For a ball mount you would need part # 36065, for a 1-7/8 inch ball part # 19256, and for a 2 inch ball part # 19258. For trailer wiring part # 18252. Cost is available at the product links.
view full answer... - What Is Needed To Tow A Pop-Up Camper With A 2004 Pontiac Grand Prix GT1Yes, you can tow a small pop-up camper with your 2004 Pontiac Grand Prix GT1, as long as the camper does not weigh more than 3,500 lbs. loaded. But, you will always want to check the owners manual or with the dealer for the gross towing weight capacity of your 2004 Pontiac Grand Prix GT1 to make sure the towing capacity is not exceeded. The Curt 1-1/4 Inch Class II Hitch, # C12225, would be a recommended hitch for your vehicle. It is a Class II hitch which has a 3,500 lbs. towing weight...
view full answer... - Hitch and Accessories Recommended for 2006 Pontiac G6 GTP CopueThere is no reason why you could not use a hitch on your G6 GTP. The Draw-Tite Class II Receiver Hitch, part # 36426 is a fit for either the coupe or the sedan. The hitch has a towing capacity of 3500 lbs, and a tongue weight capacity of 300 lbs. I would recommend checking your owners manual for information regarding the vehicle towing capacity, you will not want to exceed this capacity. You will also need a the recommended draw bar for this hitch, part # 36065, a pin and clip part #...
view full answer... - Recommended Ball Mount or Draw Bar for a 2005 Toyota PriusThe correct draw bar for your 2005 Toyota Prius will depend on the trailer hitch that you have installed. All of the trailer hitches available for your vehicle are Class I rated hitches. Trailer hitch manufacturers recommend using the draw bar that was specifically tested with their hitch. For example, if you have the Curt Class I Trailer Hitch, # C11468, installed, then the draw bar that you will want is part # C45521. If you have the Draw-Tite Class I Hitch, # 24808, then you will want...
view full answer...
Do you have a question about this Trailer Hitch Ball Mount?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
Jeffrey L
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Brian T
Updated by:
Mike S
Video Edited:
Dustin K
Installed by:
Cole B
Installed by:
David F
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Toby
7/3/2014
Okay, a year later and not a single complaint regarding this ball mount. It dutifully does its job to allow me the crazy looks people throw at me when hauling my motorcycle or my wifes latest furniture purchase. I dont know why Americans think trucks are the only vehicle to haul things.