Flash Silent Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 8" Drop, 9" Rise
(236 reviews)
Price: $270.00
In Stock
Flash Silent Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 8" Drop, 9" Rise
Item # DTSTBM6800
Our Price: $270.00
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (236)
- Q & A (0)
- Photos
Fastway Trailer Hitch Ball Mount - DTSTBM6800
- Fits 2 Inch Hitch
- Adjustable Ball Mount
- Drop - 8 Inch
- Rise - 9 Inch
- 2 Inch Ball
- 2-5/16 Inch Ball
- Two Balls
- 10000 lbs GTW
- Class IV
- Fastway
- Anti-Rattle Shank
- Aluminum Shank - Silver
- Steel Ball
Self-contained locking pins in this lightweight hitch deter theft and eliminate rattle. Go from an 8" drop to a 9" rise to swap between trailers. Tow up to 8,000 lbs with the 2" ball and up to 10,000 lbs with the 2-5/16" ball.
Features:
- Adjustable ball mount makes it easy for you to haul different trailers
- Ball height adjusts in increments of 1" so that you can easily switch between trailers with different tongue heights
- Reversible ball platform lets you swap between 2 different-size balls
- Self-tensioning, anti-rattle Silent Tow system tightens ball mount inside receiver tube and secures ball platform to ball mount
- Stops rattle and clunk
- Uses internal, stainless steel bolts for long life
- Adjusts with Allen wrench (included)
- Ball mount is machined from a solid piece of aircraft-grade billet aluminum
- Solid aluminum produces a lightweight yet strong ball mount
- Avoids welds, which can cause weak points that might break
- Polished finish creates a high-quality appearance
- Solid aluminum produces a lightweight yet strong ball mount
- 2 Chrome-plated steel hitch balls included
- Made in the USA
Specs:
- Fits: 2" x 2" trailer hitch receivers
- Ball diameters: 2" and 2-5/16"
- Towing capacity:
- 2" Ball: 8,000 lbs
- 2-5/16" Ball: 10,000 lbs
- Tongue weight capacity: up to 1,000 lbs
- Maximum rise: 9" from the top of the hitch receiver opening
- Maximum drop: 8" from the top of the hitch receiver opening
- Distance from center of hitch pin hole to back of upright bar: 4-1/4"
- Distance from center of hitch pin hole to center of ball: 8-1/2"
- 1-Year limited warranty
This Fastway Silent adjustable ball mount provides solid, rattle-free towing performance. A stainless steel pin, operated by the included hex tool, extends out from the shank and tightens the ball mount in your receiver.
To further eliminate any movement, a bolt in the side of the ball platform tightens the connection between the platform and the adjustment shank. As a result, you'll enjoy a quiet, rattle-free towing experience.
The ball platform is connected to the adjustment shank by the hex bolt located in the front of the platform. To change the ball height, simply loosen both the bolt in the front and the bolt in the side of the platform with the included tool. This will release the ball platform and allow you to slide it up and down. Or, you can slide the platform off and reverse it to change the ball size.
47-00-3800 Flash 8" Silent Tow 2" Shank 2" and 2-5/16" Chromed Balls
DT-STBM6800 Fastway Flash STBM Series Solid-Tow Ball Mount - Flash STBM Series Solid-Tow Ball Mount - 8" Drop, 9" Rise Adjustable Hitch - Solid Billet Aluminum
Customer Satisfaction Score:
93% were satisfied with this product
7% of customers were not satisfied
- Wrong item was ordered
- Defective
- Product did not meet expectations
Customer Reviews
Flash Silent Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 8" Drop, 9" Rise - DTSTBM6800
Average Customer Rating: 4.8 out of 5 stars (236 Customer Reviews)
Self-contained locking pins in this lightweight hitch deter theft and eliminate rattle. Go from an 8" drop to a 9" rise to swap between trailers. Tow up to 8,000 lbs with the 2" ball and up to 10,000 lbs with the 2-5/16" ball.by: John 07/16/2023
This hitch rocks! All you need, looks good, performs excellent BOOM! Thanks etrailer
by: Matthew06/29/2013
Great looking adjustable hitch. I purchased the non-locking version because locks and similar mechanisms seem to have issues due to salt and ice here in MN. Not sure if the locking version would have issues, but I didn't want to take the chance. Hitch is easy to adjust, seems very strong, and looks great.
by: Kyle M07/16/2015
I shopped a lot online to try to find the perfect ball mount (I'm very particular.) I really liked being able to watch a video of each individual product and how it operates, so that I could make an informed decision based off more than a couple stock photos like what other stores are offering. Shipping was shockingly quick, considering I bought the lowest grade shipping option offered. The ball mount adjusts smoothly and easily, and fits my receiver better than any I've owned before. I am extremely impressed by my dealings with eTrailer, as well as with the product itself!
by: Charles N 08/09/2015
Very happy with the quality of this hitch. Works on my 2005 dodge ram 2500 as well my 2014 dodge durango. With a standard hitch I could hear and feel the hitch banging around when connected to my durango but with this hitch it was nice and quiet. The only down side I have found is the tension pin does not go fully into the receiver of my durango but it still worked. I would recommend this hitch to anyone.
by: Bryan Snyder03/17/2011
I ordered thie DTSTBM6800 for my GMC HD2500. The quality is great. You cannot turn the ball to the inside because the holes do not go all the way through the vertical drop beam. The rattle free screws do as advertised... prevent rattling. Unfortunatelly DT does not offer this in a 2 1/2 inch size to fit my 2011 GMC HD2500. The sleeve that comes with the truck reduces the receiver size from 2.5 inches to fit the 2 inch receiver... this is the part that rattles and drives me crazy!!! I'm currently troubleshooting to resolve this issue.
Lucky
8/31/2014
Thats my problem also!!!! Why can they not make us a 2-1/2 reciever???? Common fellas let get er done!!!
Rachael H.
9/3/2014
Diversi-Tech does make adjustable ball mounts for 2-1/2 inch hitch receivers. For example the # DTALBM6825 is the same as the one that you mentioned, and it has an integrated sleeve to work with 2-1/2 inch hitches.
by: Chris09/16/2014
I love the idea.....but I have a couple problems with the hitch. First, it will only work on one of my two tow vehicles. The 2" shaft for the receiver pin is not long enough to clear my bumper.
The other problem I have is that the bar that adjusts the height of the two balls should have a couple more holes drilled for more height settings.
I will say the build quality is fantastic.
by: Wayne W.06/24/2013
Shipping was good arrived on schedule date. Used it to tow my 8,000 lb. boat was nice to be able to raise the trailer so it was level and not having the tongue of the trailer lower than the rear of the trailer. Now when I tow my small boat with 13" tires all I have to do is flip the ball mount and lower it. Great Product well made and in the USA.
by: Clive11/02/2019
VERY WELL ENGINEERED PRODUCT, SUPERB FINISH, WELL PACKAGED AND PRESENTED BY MANUFACTURER.
USUAL EFFICIENT SERVICE FROM etrailer WITH IMMEDIATE RESPONSE AND COMPETITIVE PRICING & DELIVERY EXACTLY AS PROMISED.
PRODUCT CHOSEN TO GET THE TOW BALL RAISED TO WORKING HIEGHT ( 18 " ) ON 2016 MERCEDES BENZ METRIS VAN WHICH HAS A TERRIBLE " UNDER THE BACK BUMPER " DRAWBAR GIVING A 13 " CENTER HIEGHT. PRODUCT FITS FLUSH TO OUTSIDE OF BUMPER ( OTHERS STICK OUT DANGEROUSLY ) AND JUST ALLOWS THE REAR DOORS TO OPEN. FUNCTION OVER FORM BUT IT DOES LOOK GOOD IN PLACE !
by: ROY07/22/2014
Mark was very helpful in handling a problem with the tamper proof key. Thank you for taking care of the issue. Adjustable ball mount worked great on a recent 1000 mile trip. Thumbs Up.
by: Josh D06/10/2017
This is second fasthitch a very good product best hitch I've ever used.. would recommend this hitch to anyone that pulls different trailers alot..
by: Dave W.03/21/2014
This is a replacement drop for the one that was on my truck when it was stolen. I had forgotten the exact model number of the drop I had purchased, so I emailed etrailer asking if they had records of all my previous purchases. Within the hour I received an email with all my previous 7 years of purchases.
Love their products and dedicated customer service.
by: LLL07/14/2017
There is a problem with the product. I had indicated that my vehicle was a Ford Explorer. I purchased this product specifically for the non-rattle aspect. Unfortunately the receiver on the Explorer is too short to allow the non-rattle apparatus in the actual receiver. Therefore this aspect is useless. Any suggestions?
by: mike m10/06/2014
product came in just as described. hitch is very well made, i love it. etrailor gave me and easy way to order and very fast delivery time. would buy from them again!!
by: Jason G.03/06/2011
I'm impressed with the fit, finish, & quality of this adjustable ball mount. The adjustment is quick/easy and it doesn't rattle like most other ball mounts I've used. Another key feature for me is that this mount is constructed of aluminum. My truck is exposed to the elements of New England (excessively salted roads & living on the Seacoast), so I will never have to worry about this mount deteriorating due to rust.
by: Bruce B.11/12/2013
Quality and fit are excellent. Finish is exquisite.
Special allen wrench helps with security.
Have not used it yet, but I have high expectations.
E-trailer's communication is unsurpassed and fast.
I am a repeat customer and will shop here again.
by: Craig J10/09/2019
Rock solid performer. This hitch had no play in it and it easy to clean and looks great.
by: Mike R10/13/2016
It's a great receiver use it in my Duramax quite often we wouldn't be without it.
by: William 11/19/2019
I really like the quality. And the value for the money.
Etrailer is always great to deal with.
by: ike in CO05/07/2017
happy with it so far way better than the razor brand we bought from another site!
Ike C.
5/7/2018
after a year still works as new and it is still tight with no movement
by: Dave W.06/27/2009
Serves my purpose very well!Execellent service and delivery. I would recommend etrailer to anyone!
by: JMartin03/26/2015
This product does exactly as advertised. The item did not rattle
at all. The first I have seen that doesn't rattle. it is very nice looking
as well. Looks great on my 2014 Yukon Denali.
by: Olivia 10/16/2014
Excellent customer service. Ricky helped me sort through what product would be best when my original product was on backorder and I needed it promptly. Highly recommend working with Ricky and this company. I will in the future.
by: TomG06/25/2015
Service was perfect - ordered Sunday delivered Wed
Product was just what advertised - well made and am sure will outlast current truck and its owner- - seems just right for new Denali
by: James05/30/2014
Great product and excellent communicati on!!
by: buyer04/11/2012
Easy to install & adjust; very quiet; absolutely solid.
25
236
Show More Reviews
See what our Experts say about this Fastway Trailer Hitch Ball Mount
- Distance From Center of Hitch Pin Hole to Anti-Rattle Device on Fastway Adjustable Ball MountsOn the Solid-Tow Adjustable, Aluminum Ball Mount # DTSTBM6800 it measures 2 inches from the center of the hitch pin hole to the center of the anti-rattle pin on top of the shank. That would mean half of it would make contact with your hitch and the other half would outside of the hitch opening since your hitch pin is 2 inches from the center of it's hitch pin to the end of the hitch opening. This would be enough for it to still function. I have included a link to a video review of this...
view full answer...
- How to Determine the Right Rise or Drop Needed when Choosing a Ball MountThe amount of clearance needed is going to be different for every vehicle, trailer, and possible terrain you may encounter. For example, a lifted truck towing a large travel trailer through the plains would not have a problem with ground clearance. A minivan towing a pop up camper in the mountains and offroad is likely going to encounter ground clearance issues if the adjustable ball mount drops low enough. What you can do is determine the amount of drop you need by taking a few measurements....
view full answer... - Aluminum Ball Mount with 8 Inch Drop to Position a Trailer Inside a GarageWhether or not the lower ball would make contact with the ground depends on how high up the tow vehicle is. If you were to measure from the ground to the top of the receiver tube on the vehicle when on level ground, then subtract 8 inches, that will give you an idea of where the bottom of the TOP ball will be. That alone should tell you if the lower ball would be too low. You do not want to cut the ball because it will void the warranty and also make the ball mount unsafe to use. Instead,...
view full answer... - Tongue Weight Capacity for Fastway Solid-Tow Adjustable 2-Ball Mount # DTSTBM6800The Fastway Solid-Tow Adjustable 2-Ball Mount # DTSTBM6800 referenced in your question features a 1,000 pound tongue weight capacity, regardless of which ball you are using. The towing capacity will change based on the ball size; 8,000 pounds with the 2 inch ball and 10,000 pounds with the 2-5/16 inch ball. Using the ball mount in the drop or rise position will not affect its weight capacitiy at all. I have attached a short video demonstration that you can also check out.
view full answer... - Can Sleeve on Diversi-Tech # DTSTBM6825 Ball Mount Be Removed for Use in a 2 Inch HitchThe 'sleeve' on the # DTSTBM6825 is fixed in place and is not removable. I do have a suggestion for you, however. Go with the ball mount for a 2 inch receiver, part # DTSTBM6800 and when you need to use it in your 2-1/2 inch receiver, use a reducer sleeve like part # 58102. This ball mount also uses a 2 and a 2-5/16 ball and has a 10K capacity. This is an identical ball mount, minus the sleeve.
view full answer... - Will the Adjuster/Tensioner Screw Come Loose When Towing a TrailerI spoke with my contact at Diversi-Tech about the Adjustable Solid-Tow Aluminum Ball Mount, # DTSTBM6800. He stated that the unit has a binding nut to lock it in place. This creates a double redundancy to keep the unit from coming loose. He also stated that this particular unit is not intended for use in harsher climates where a lot of salt is used on the roadways in the winter if you plan on leaving the mount attached to the vehicle all the time. It is also recommended that you grease...
view full answer... - Can I Use a Higher Rated Ball Mount?Yes, you can use a ball mount like item # DTSTBM6800 that has a higher capacity than your Subaru Ascent. You will just have to go off of the lowest capacity either your vehicle or hitch has. A better option would be to use the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It also includes a hitch pin and clip, hitch receiver lock with keys, hitch cover, and a storage case. I have...
view full answer... - Distance from Center of Hitch Pin Hole to Center of Anti-Rattle Pin on Fastway Adjustable Ball MountOn the Solid-Tow Adjustable, Aluminum Ball Mount # DTSTBM6800-2S it measures 2 inches from the center of the hitch pin hole to the center of the anti-rattle pin on top of the shank. I have included a link to a video review of this ball mount for you.
view full answer...
- Aluminum Adjustable Ball Mount Recommendation for 8 inches of DropI have a solution for you, but if you need up to an 8 inch drop the Andersen ball mount part # AM3411 that you referenced can only do a max drop of 5-1/2 inches. For a similar adjustable ball mount that can do up to 8 inches you would want the part # DTSTBM6800 instead.
view full answer... - Possible Adjustments On Solid-Two Adjustable Ball Mount # DTSTBM6800You can choose to insert the shank of the Solid-Tow Adjustable Ball Mount # DTSTBM6800 into your trailer hitch so the vertical bar rise above the shank rather than drops below it. By doing this, you will gain additional height for your trailer, up to a 9-inch rise. I have included a link to our FAQ page on how to select the correct rise/drop ball mount. Inverting the mount in this way will not change the 10,000 lb total weight capacity or the 1500 lb tongue weight capacity of this product...
view full answer... - 2 Ball Adjustable Ball Mount Recommendation that Can Do Up to 9 inches of DropFor an aluminum adjustable ball mount that fits all of the criteria you mentioned you would want the part # DTSTBM6800-2S. This has both ball sizes you need, can drop down as low as you need, and has an anti-rattle device built into the ball mount as well.
view full answer... - Operation of Anti-Rattle Function on Diversi-Tech Solid-Tow Adjustable Ball Mount # DTSTBM6800-2SThe Diversi-Tech Solid-Tow Adjustable Ball Mount # DTSTBM6800-2S will work properly in the 2-inch hitch on your 2005 Dodge Ram 2500. The anti-rattle pin that extends up from the top surface of the shank will still have enough of the receiver tube to press against to stabilize the shank. Actually, the further to the rear of the hitch pin hole that the anti-rattle pin sits the more leverage it will have to exert pressure on the inside of the receiver tube. The linked video will illustrate...
view full answer... - Problem Replacing Diversi-Tech Stainless Double Ball # DTBM28 on Diversi-Tech DTSTBM Ball MountsThank you for your recent purchase. The Diversi-Tech Replacement Stainless Double Ball # DTBM28 that you purchased from etrailer will fit several of their ball mounts. For applications with the Solid-Tow Series the correct procedure which you followed is to tighten the set screw all the way in so that the ball can be removed. In other applications it is okay, according to my technical contact at Diversi-Tech, to back the screw out instead. In either case you need to get it out of the way...
view full answer... - Can Diversi Tech Adjustable Ball Mount Be Converted to Having Ball Sizes 2 inch and 1-7/8 inchI wish we had an easier solution but the only way to get a version of the Diversi Tech Adjustable Ball Mount # DTSTBM6800 with the hitch ball sizes of 1-7/8 inch and 2 inch you'd have to swap out what it includes with the # DTBM23.
view full answer... - Are Replacement Shanks Available For the Fastway Solid-Tow Adjustable Ball Mounts? Currently Fastway only offer their adjustable ball mounts like the Solid-Tow Adjustable 2-Ball Mount w Chrome Balls # DTSTBM6800 as a kit with the shank and ball mount. They do not offer replacement shanks separately. Be sure to get a etrailer Trailer Hitch Receiver Lock # e98882 to secure your investment in your receiver.
view full answer... - Will the Rapid Hitch Ball work with a Fastway Solid Tow?I pulled these two products and tested them out together. I can confirm that the Rapid Hitch 2" ball # AM3453 will work with your Fastway Solid Tow # DTSTBM6800.
view full answer... - Is a Solid-Tow Aluminum Ball Mount Available With 2 Inch and 1-7/8 Inch BallsYes, we have a product like this available from Diversi-Tech, it is the Solid-Tow Adjustable Aluminum Ball Mount, part # DTSTBM6407, which has a 2 inch and 1-7/8 inch hitch ball. This ball mount is adjustable to give you up to a 5 inch rise or an 4 inch drop and it is compatible with 2 inch receivers. To secure part # DTSTBM6407 to your hitch, you may be interested in the Trailer Hitch Receiver Lock, part # e98882.
view full answer... - What 180 Hitch Ball Mount do you Recommend for my 2018 Jeep Grand CherokeeFor your 2018 Jeep Grand Cherokee I recommend using the 180 Solid-Tow Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 6" Drop, 7" Rise # DTSTBM6600 it is just a little bit shorter and will allow you to haul many trailers with different coupler heights. The 8" drop is going to be just a little too long and could pose an issue with ground clearance.
view full answer... - Weight of the Solid-Tow Adjustable 2-Ball Mount w Chrome Balls Part # LTB8-2The Solid-Tow Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 8" Drop, 9" Rise # DTSTBM6800 has a shipping weight of 19 lbs which means the actual weight is likely around 17 lbs.
view full answer... - Hitch and Ball Mount Recommendation for a 2008 Mercury Grand Marquis Needing a 3 inch RiseFor a Class III 2 inch hitch for your 2008 Mercury Grand Marquis you would want the Curt Hitch part # 13707. When we installed this hitch on a similar vehicle we found that from the ground to the top of the hitch opening was 13-1/4 inches. Assuming the rental company you talked to was right, and their trailers will be about 16 inches from the ground to the bottom of the coupler you would need about a 3 inch rise. I think your best solution would be to get the etrailer.com ball mount kit...
view full answer... - What is the Weight of the Solid-Tow Adjustable 2-Ball Mount w Chrome Balls # DTSTBM6800The Solid-Tow Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 8" Drop, 9" Rise # DTSTBM6800 has a shipping weight of 20 lbs. It looks like it should weigh more but thankfully aluminum is pretty lightweight.
view full answer... - Extra Long Shank Adjustable Ball Mount with 3 Inch Rise to Clear Rear BumperI was able to find a ball mount that offers more than 6 inches of clearance between the hitch pin hole and the back of the ball mount upright for you. The MaxxTow Adjustable Height Ball Mount # MT70068 offers 8-1/8 inches from the pin hole to the back of the adjustable portion of the ball mount. I've attached a dimensional diagram showing a number of measurements on this ball mount for you. This mount offers a minimum rise height of 1-3/4 inches with a maximum rise of 6-1/4 inches. The...
view full answer...
- Availability of Replacement Double Hitch Ball for Adjustable Ball Mount It sounds like you have an adjustable ball mount like the Fastway Solid-Tow 2-Ball Mount # DTSTBM6800 that features both a 2 inch ball and a 2-5/16 inch ball. If this is the model you have, you can easily replace the hitch balls with # DTBM28. In order to replace the hitch balls, you will just need to use the hex adjustment tool # DTBM26 to loosen the hex bolt that holds the ball platform to the ball mount and slide the platform off the mount. Then run the hex bolt that holds the balls...
view full answer... - Are the Balls on the Diversi-Tech Solid-Tow Adjustable Ball Mount # DTSTBM6800 ReplaceableThe hitch balls for the Diversi-Tech Solid-Tow Adjustable Ball Mount, # DTSTBM6800, are easily removable and replaceable. You simply thread the front allen bolt all the way in, slide the balls out of the ball platform and insert the new hitch balls. I made a short video for you showing how this is done. We also carry replacement hitch balls. For a 2 inch and 2-5/16 inch ball set, you can use part # DTBM28 and for a 1-7/8 inch and 2 inch ball set, use part # DTBM23.
view full answer...
Do you have a question about this Trailer Hitch Ball Mount?
Info for this part was:
Updated by:
Lindsey S
Updated by:
Adele M
Updated by:
Laura H
Updated by:
Shelly K
Updated by:
Wilson B
Updated by:
Amanda M
Updated by:
Mike S
Updated by:
Ryan F
Video Edited:
Patrick B
Video Edited:
Chris R
Written by:
Raymond P
Expert Research:
Michael H
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Installed by:
Cole B
Installed by:
Randy B
Video by:
Zach D
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Kyle M.
7/15/2016
Still fantastic!