Arrives before Christmas To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Average Customer Rating: 4.3 out of 5 stars (40 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
So I haven’t exactly worked this thing very hard since it’s bolted to my 4-cylinder Honda Element, but it has worked well for what I ask of it. It’ll pull a trailer of lumber home from the hardware store or a trailer of yard debris to the dump, which is all I really ask of it.
Installation wasn’t too bad. The modifications grinding away the frame weren’t as tough as I feared. Just used my Dremel and a set of cheap grinding burrs for it rather than buying a proper die grinder that I might never use again.
The hardest part was trying to hold it up and get all the bolts in without things twisting or pitching such that the holes didn’t all line up. Would definitely be easier with 2 helpers to hold it up while you bolt, but I managed to rig something up and do it solo.
One potential improvement to the install instructions: put a piece of tape over the nearby holes in the frame that you are *not* using. That way you don’t accidentally put a bolt in the wrong hole and then spend an hour fishing it back out of your frame.
Pros: Excellent finish.
I was a little worried about having to enlarge a few holes in order to get this hitch to fit. It turned out that it was very easy. I used a dremel tool to enlarge the hole, and the fish wire made it easy. (see the attached pics). Dont forget to paint the hole when done.
One other note was that the hitch didn't fit out of the box, I had to 'persuade' the center portion (where the U bolt goes) with a hammer in order to get the mounts to line up. It only took a little hammering and then it fit perfectly.
All in all I am very happy, but I took a star off for the adjustments .
Hitch was bent on arrival. Wish they included two springs to fish the bolts
Awesome hitch, perfect fit and works amazing with my 1up USA bike rack
I've had it a year and used it a lot. Works perfect, rugged, and doesn't move around at all
I have it attached to a Honda Element and use it to haul lightweight dirt bikes.
Highly recommend it
It looked very nice when installed.
Holes in the hitch were not exactly lined up. Had to wedge the side out to get it lined up during install.
You did very good. The product looks good. The video's on the tracking page are great. I have not installed it yet. The box did end up with a whole in it with the hitch popping out.
Bought this to replace the previous Curt class 1 hitch. It came with some scratches in the paint, admittedly from mishandling by etrailer; they said they store them on a shelf and they get banged around which they should work to avoid. I had to clean quite a few spots, prime and paint, which took an extra couple of days of work because I had to wait for the paint to cure.
I also struggled a bit to get this one to line up. The bolts went in rather easily after I made the necessary clearance cuts, but I almost had to pre-bend the frame slightly with a “drift pin” to get the holes to align. My frame is not racked so that didn’t really make much sense. The previous Curt hitch still fit very well.
After a season of use though, it is solid and has not given me any problems. Very reliable and never moves. It feels well made and well attached to the frame.
It's a well made hitch receiver and wiring harness. The installation process was well thought out. I followed the hitch instructions, and thought fishing the bolts was going to be harder than it actually was. The instructions were easy enough to follow. The wiring kit under the dashboard was plug-and-play, with no issues. In my installation, I chose to do something not mentioned in the instructions, and I adjusted the rear tow loop on my Honda Element, so that the center of the hitch could attached a little higher, making it more snug up to the bumper. This variance is unrelated to the quality of the products made by eTailer.
there are several choices when it comes to hitches for the honda element. i chose this one because others need the bumper to be trimmed for correct installation. this one from curt though did not require that. the only difficulty installing this one is that holes in the honda frame needed enlarged on the sides to allow for hardware to be put in place. access isnt great but using a rotary file in my drill seemed to work pretty good. make sure you wear your earplugs though. the hitch fits and looks great. wiring is easy, however instructions dont tell you how to get the wiring from the connection inside by the spare tire to outside where the hitch is at. i chose to remove a plastic cap beneath the spare and under the jack. i bought some plastic insulation and wrapped the wire for a little extra protection and it works great.
Gave some thought to putting this on myself but I do not have access to lift or jack stands. Good thing that I have a great mechanic because the holes did not line up so the hitch needed some strenuous persuasion to move the holes into alignment with the pre drilled holes in the vehicle frame. The rest of the installation went smoothly and I am very happy with the end result. If you are thinking of doing this yourself, have a back up plan since the MFG does not appear to be checking tolerances on the product. The misalignment was NOT due to shipping as the carton was sturdy and showed NO sign of damage.
Shipped to wrong address. My order said to ship ID . However you shipped it to my home address where the car needing the trailer hitch he is not at and the trailer hitch now needs to be shipped to Idaho. However I won’t be back to Idaho until early July
The hitch is made well, however the fitment requires bending of the arms to make it fit an '07 Honda Element. Ideally, I would prefer to not have to bend metal to get something to fit, just because if you bend it incorrectly you've just made an expensive item un-returnable. Over all, happy with the hitch.
We had a Pep Boys install our hitch because it wasn’t expensive and we are not very handy with tools. The installation was a breeze and the hitch looks and works great! We use a lot of different bike trailers works great with all of them.
Great fit and easy install on my 2008 Honda Element. Their videos and thorough answering of questions are why I keep coming back. Great job!
The Curt hitch was very difficult to in stall.
The bolt holes wouldn't line up. They were off by a few inches. It was impossible for me to mount. Customer service gave me a full refund and return.
Katrina B.
10/3/2022
If you are having troubles with the holes not lining up, it could be that the hitch has been flexed during shipment. This is common amongst hitches, since the mounting brackets are made from a mild steel that allows the hitch to flex with the vehicle after installation. If the entire hitch was made of rigid steel, there would be a greater chance of the hitch being damaged and experiencing stress cracks. Such cracks could cause the hitch to malfunction. This flexing often times will cause the holes not to align. Because of this we do have a help article I have the link attached below that will walk you through the process of straightening the hitch.
Helpful Links
2nd time I've ordered for you guys, and it has always been a smooth sale, thank you!
Easy installation!
Holes for the bolts didn’t aligned. Had to adjust by drilling new holes.
Katrina B.
8/12/2022
We do not recommend drilling new holes into the hitches. If you are having troubles with the holes not lining up, it could be that the hitch has been flexed during shipment. This is common amongst hitches, since the mounting brackets are made from a mild steel that allows the hitch to flex with the vehicle after installation. If the entire hitch was made of rigid steel, there would be a greater chance of the hitch being damaged and experiencing stress cracks. Such cracks could cause the hitch to malfunction. This flexing often times will cause the holes not to align. Because of this we do have a help article I have the link attached below that will walk you through the process of straightening the hitch.
Helpful Links
I like the Curt hitch..Delivery was prompt and I had a muffler shop install it for $xxx.xx…Thanks
I’ve had this for one year now, no issues. It was a bitch to install, but now that it’s on I love it!
Sturdy and well built . Not the best fit . Took much more persuasion than I would have wanted from a product that cost as much and was as beefy as the one I received
installed as advertised, all good so fa r.
I am more than satisfied with the whole process from the time I put the order in to the time the order was delivered.
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Peter A.
3/25/2023
well, the hitch works well, but installing it was a job. The upper front connection point did not line up at all. It needs to be bent to more of a 90 degree angel. So after some time bending it to make it work, it fit. This did break the powder coating on this tab.