Dexter 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 3,500 lbs

See what our Experts say about this Dexter Trailer Hubs and Drums

• Replacement Hub-and-Rotor Assembly for 2000 640 Ranger Boat Trailer With Tandem Axles
  In order to find if the Dexter 10" Hub-and-Rotor Assembly # K08-435-05 will fit your 2000 620 Ranger boat trailer you will need some additional information. This assembly is designed to fit a 3,500 lb axle with the standard # L68149 inner and # L44649 outer bearings. I recommend checking your axle tag/bearings to see if this will fit. The axle tag should have the capacity. It is also likely this has a serial number which could be used to identify the axle and the bearings it uses. If you...
  view full answer...
  
• Recommended Dust Cap for Dexter 10" Hub-and-Rotor Assembly
  The Dexter 10" Hub-and-Rotor Assembly part # K08-435-05 works with the Grease Cap part # F001518.
  view full answer...
• Bearing Kit For Dexter K08-435-05 Hub & Roter
  The correct bearing kit for your Dexter 10" Hub-and-Rotor Assembly # K08-435-05 is the following: - Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles # BK2-100
  view full answer...
• Are There Pre-Greased Versions Of The Dexter 008-435-05 Hub/Rotor
  Hi Wendell, We do offer compatible replacement hub/rotors for your Dexter 008-435-05 but they unfortunately do not come pre-greased. I recommend picking up the # K08-435-05 as well as bearings # L68149 and # L44649, and grease seal # RG06-050 to pre-pack the hub yourself with some lube # L11380 before the trip. To prevent the bearings from falling out or any dirt/debris from getting inside the hub you can put two layers of plastic wrap over the holes and rubber band them down.
  view full answer...
• Replacement Hub for ShoreLand'r SLR31BLW
  Hi Steve; based on my research it looks like you have a 3,500 lb axle and it came with a hub/rotor for UFP disk brakes. We don't have an exact parts list so I recommend verifying this information to be sure. You can check your axle tag for a serial number or pull your hubs and bearings to identify them. Assuming that is correct, you can use the Dexter 10" Hub-and-Rotor Assembly # K08-435-05 you were looking at as a replacement. You will also need the # BK2-100 bearing kit. I have attached...
  view full answer...
• Is the Dexter 10 inch Hub and Rotor a Good Replacement for a MagicTilt UFP Trailer
  The bearings # L68149 and # L44649 being identical on the Dexter Hub and Rotor # K08-435-05 is a great start! The other thing that you will need to determine is if the seal is the same as well. The correct seal can be found with part # RG06-050 and has an Inner Diameter of 1.719 inches and an Outer Diameter of 2.565 inches. If you cannot find the part number on your seal and you don't already have one, you can use a Carbon Fiber Digital Caliper # PTW80157 to determine what the size of your...
  view full answer...
• Replacement Hub And Rotor Assembly For A 2008 Shorelandr Boat Trailer
  After doing some research it seems that your 2008 Shoreland'r boat trailer has a 3,500 pound weight capacity so The Dexter 10 inch Hub-and-Rotor Assembly # K08-435-05 would work for you. Your axle should have an axle sticker or plate on the axle that will inform of you the weight capacity. The bearings are sold separately so you will have to get The Inner Bearing # L68149 and The Outer Bearing # L44649. If your axle does not have an axle sticker or plate located on it if you pull off...
  view full answer...
• Replacement Seals And Hubs For Boat Trailer W/ 3500lb Axles And Oil Bath Hub and Rotors
  There are special seals to convert your 3500lb rotors to oil bath, and they can be replaced with Replacement Seal For 3500-lb Axles # XLPROLUBE1980SEAL. While we do not offer 9-3/4" rotors for your 3500lb boat axle, we do have the Dexter 10" Hub-and-Rotor Assembly # K08-435-05 which measures 10" in diameter, and is designed for 3500lb axles. This rotor uses inner bearing # L68149, outer bearing # L44649, and grease seal # RG06-050(you will not need the grease seal as you will need the...
  view full answer...
• Replacement Idler Hubs for a EZ loader Oil Bath Hub Assembly
  I would be happy to help you! The EZ loader oil bath hub assembly 300-029534 is a complete 5-on-4-1/2 idler hub kit that includes races, bearings, seal, washers, nut, retainer nut and cotter pin, bearing protector and lug nuts. Some of these hubs fit on a straight spindle, meaning as spindle that uses the same part for both its inner and outer bearing. The actual bearing numbers are not provided on their site. Our best option would be the Trailer Hub Assembly for 2,000-lb Axles - 5 on 4-1/2...
  view full answer...
  
• 5 Lug Hub/Rotor Recommendation for Trailer with Bearing Numbers L44649 and L68149
  Thanks for getting me the bearing numbers and bolt pattern of your hubs. With that info we know that the Kodiak Hub/Rotor part # KHR10D or the Dexter part # K08-435-05 would be what you need.
  view full answer...
• Recommended Replacement Hubs for EZ Loader Trailer With Disc Brakes
  The VIN doesn't give me really any information beyond what you already gave so I reached out to the manufacturer. You have the 3,700 lb axle, but it has the standard 3,500 lb spindle size based on the bearing numbers they gave me for your axle. I recommend the Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-1/2 - Galvanized # AKIHUB-545-35-G-EZ-K if you are just looking for the hub for a rotor to fit over, or # K08-435-05 if you are seeking an integrated rotor. The...
  view full answer...
• Can Dexter 10 Hub and Rotor # K08-435-05 be Used on EZ Lube Spindles
  The Titan 10" Hub and Rotor # K08-435-05 that you referenced can be used with EZ lube spindles. In order to do that you'd need to use the correct grease caps and you'd be set. For that all you need is the part # RG04-040 which has the removable center sections to make it EZ lube spindle compatible.
  view full answer...
• Recommended Disc Brake Kit to Convert From Electric Brakes on 1984 Fleetwood Terry Travel Trailer
  In order to make sure you get the right brake kit I would not make any assumptions. It would be best to go ahead and pull the hub and take measurements just to be safe. See the helpful diagram below if you aren't sure where to measure. I recommend using a digital caliper like the # PTW80157 to take your measurements. It is possible that you could find part numbers on there but I'm guessing they have worn off. Once you have you have your measurements you will be able to find the correct...
  view full answer...
  
• Is There a Replacement Hub For A 1980 Apache Pop-Up Camper With Fayette Hubs
  I will have another option available, but with the widths you got, you have an inner bearing # L44643 and an outer bearing # LM11949. The length of your spindle is also going to mean you have one that is shorter than standard and we will not have a replacement available. With that being said, I recommend replacing the axle with something that uses a more common length and bearing combination. Though it will require measuring from the center of one spring seat to the center of the other...
  view full answer...
  
• Replacement Disc Brake Hub and Rotor Assembly For a 2014 Marine Master Boat Trailer
  I reached out to Marine Master Trailer who provided me with a list of the parts needed for your trailer. Dexter 10" Hub-and-Rotor Assembly # K08-435-05 Qty 2 Inner Bearing # L68149 Qty 2 Outer Bearing # L44649 Qty 2 They could not provide me with the correct grease seal size but it will be either the Seal # 58846(inner diameter 1.719) or Seal # 168255TB(inner diameter 1.687).
  view full answer...
• Can Dexter 10" Hub-and-Rotor Assembly be Used as Oil Bath
  The Hub/Rotor part # K08-435-05 can be used as an oil-bath setup with the Kodiak XL ProLube Kit for 3500-lb Axles # XLPROLUBE1980KIT which comes with everything needed.
  view full answer...
• Is Titan Disc Brake Kit T4843800 Made in the USA?
  The Titan Disc Brake Kit and BrakeRite Electric-Hydraulic Actuator - Tandem, 3,500-lb Axle # T4843800 are great quality but they are not manufactured in the USA. The bearings are also not Timken brand as the manufacturer makes their own bearings. Titan was bought by Dexter which is an USA made company so the major components can be used as an alternative. For instance the Dexter DX Series Electric Over Hydraulic Brake Actuator for Disc Brakes - 1,600 psi # K71-651 can be used as an alternative...
  view full answer...
• Replacement Disc Brake Rotor/Hub For a 1990 Ranger Trail Boat Trailer
  The Dexter 10" Hub-and-Rotor Assembly # K08-435-05 is designed to fit a 3,500LB trailer axle with the Inner Bearing # L68149, Outer Bearing # L44649 and Grease Seal # RG06-050. To confirm if this is what matches the axle on your 1990 Ranger Trail Boat Trailer, you will need to inspect your current hub for the bearing and seal information. If you are unable to find the information stamped on the bearings and seals you can measure your spindle with a Digital Caliper # PTW80157. Once you have...
  view full answer...
  
• Replacement Brake Hub/Rotors UFP 9.75 rotors with 10 demaxx ?
  We don't carry Demaxx products, so I couldn't say if they'd be compatible replacements. We do carry some 10 inch hub/rotors from Dexter and Kodak, both of which are for a 3500 lb axle and use an L44649 outer/L68149 inner bearing. The Dexter # K08-435-05 measures 9.75 inches in diameter, so if the bearings your existing rotor uses are compatible with the L44649/L68149 they'll work for you.
  view full answer...
• Replacement Hub for 2005 Eagle Boat Trailer
  In order to determine which hubs you're going to need as a replacement you will need to pull the hubs to see what bearings will fit on your spindle; the bolt pattern is only part of the equation, but still helpful to know. To accomplish this you can either check the numbers that are stamped on the backs of the existing bearings, or measure the spindles where the bearings sit using a digital calipers like the # PTW80157. The Dexter 10" Hub-and-Rotor # K08-435-05 is designed for use with...
  view full answer...
  
• Can Larger 3,500 lb Brake Rotor Be Used As Replacement On Trailer
  Although both of those fall under a 10" hub and rotor assembly, it sounds like you do not have DeeMaxx on there right now. In general the disc brake parts cannot be interchanged. The # DE49VR you got has a 10-3/16" diameter, Kodiak # KHR10D sits at 10", and then there is Dexter # K08-435-05 which matches your 9-3/4" measurement. Seems like you have Dexter on there right now so you would want to stick with Dexter replacement parts assuming that is correct. The other option would be to swap...
  view full answer...
• Replacement Seals For An H-1377 Trailer Hub
  Hey Michael, I'm seeing a lot of conflicting information on the part numbers you provided and the measurements you provided need to be at least another decimal point longer to determine exactly which seals you have. To make sure everything is correct it'd be best if you measured the spindle with a caliper # PTW80157 at points B, C, and D from the diagram and the bore hole of the hub. If I can't find a suitable replacement for the seal and we have to go with a new hub then I'll also...
  view full answer...
• Does the Dexter 10" Hub-and-Rotor Assembly K08-435-05 Require a Press In or Threaded Cap?
  The Dexter 10" Hub-and-Rotor Assembly # K08-435-05 accepts a Grease Cap # F001518 or Lubed Dust Cap & Rubber Plug # DC200L-DCRP for EZ Lube Spindles. The Kodiak XL ProLube Kit # XLPROLUBE1980KIT will give you a press in base that includes a threaded cap with center plug. It also includes a oil seal to use in place of a Grease Seal # RG06-050 to keep the oil in the hub. You will then only need the Inner Bearing # L68149 and Outer Bearing # L44649 to attach to your spindle.
  view full answer...
• Replacement Rotors and Brake Pads For EZ Loader Boat Trailer With Kodiak 3,500LB Disc Brakes
  Since you have a Kodiak Disc brake caliper on your EZ Loader boat trailer you will want to replace it with the Kodiak Integrated Rotor # KHR10D. This rotor is 10" in diameter while the Dexter # K08-435-05 you found is only 9-3/4" in diameter. The difference in diameter would lead to wear issues on the pads. It is best to install new Pads # K225CPSS when you change your rotors so the pads can bed in properly on the new rotor.
  view full answer...

Do you have a question about this Trailer Hubs and Drum?