Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs
(743 reviews)
Price: $65.98
Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs
Our Price: $65.98
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (743)
- Q & A (0)
- Photos
etrailer Trailer Jack
- Boat Trailer
- 0 - 1000 lbs
- Sidewind Jack
- Swivel Jack
- Bolt-On
- Pull Pin
- Leveling Jacks
- Tongue Jacks
- 10 Inch Lift
- With Wheel
- Steel
- etrailer
Corrosion-resistant, clear zinc swivel jack with 5-3/4" wheel is perfect for marine use as well as other recreational applications. Jack has an extended height of 23-1/2", a retracted height of 13-1/2", and a capacity of 1,000 lbs.
Features:
- Marine jack lets you raise and lower your boat or recreational trailer
- Swivel design lets you swing jack up for storage, down for use
- Single bolt-through design provides extra side-load support
- Convenient 1/2", spring-loaded pull pin secures and releases jack
- Plastic wheel lets you move your trailer
- Inner tube rotates with wheel allowing you to move in any direction
- Sidewind handle has comfortable, grooved grip
- Corrosion-resistant clear zinc finish for durability
- Bolt-on installation to the side of your trailer
- Mounting bracket and hardware included
Specs:
- Application: trailers with a frame height from 2" to 4"
- Bracket height (from bottom of wheel to center of bracket):
- 13-1/2" Retracted
- 23-1/2" Extended
- Travel: 10"
- Outer tube diameter: 2"
- Inner tube diameter: 1-3/4"
- Wheel dimensions: 5-3/4" diameter x 2" wide
- Mounting bracket dimensions: 6-3/4" long x 5-3/4" wide
- Handle radius: 7"
- Lift capacity: 1,000 lbs
- 1-Year warranty
MJ-1206B Ram Round Swivel Marine Jack - Bolt On - Zinc - Side Wind - 10" Travel - 1,000 lbs
Item # MJ-1206B
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Arrived Damaged
Customer Reviews
Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs - MJ-1206B
Average Customer Rating: 4.8 out of 5 stars (743 Customer Reviews)
Corrosion-resistant, clear zinc swivel jack with 5-3/4" wheel is perfect for marine use as well as other recreational applications. Jack has an extended height of 23-1/2", a retracted height of 13-1/2", and a capacity of 1,000 lbs.by: Kirk 08/29/2022
This jack is heavier duty than it looks. Much needed for my motorcycle trailer that didn't come with one. Install took ten minutes.
by: Al B.03/31/2018
First let me say that Customer Service at etrailer is outstanding. The first jack I tried was recommended for my trailer by a tech but it did not fit my trailer. Customer Service was quick to help me out by authorizing the return and recommending the MJ-1206B jack which arrived in two days. The jack fit fine but there’s some “play” between the mounting bracket and the swivel bracket, and the jack stood slightly off vertical once the weight of the tongue was on it. Unlike a stationary jack there would need to be some amount of play between the brackets so that the jack can easily swivel up and down, which it does and it rolls easily as well. A previous review described a similar condition so it appeared the bolt and space between the two brackets was likely preset correctly although the reviewer said he was able to tighten the bolt somewhat, which I was unable to do. I called customer service and was told there would be some play between the brackets and the jack should operate fine. I need to move the trailer by hand each time I use it so it will get a good test of its durability. Again, customer service is excellent at etrailer!
Al B.
3/31/2019
My MJ-1206B trailer jack continues to function properly after a year of use and makes moving my trailer easy.
by: Philip07/14/2023
The swivel jack is fine, however, the wheel broke. I believe it was the plastic spoke of the wheel. I asked if they would replace it under warranty but they said it was out of warranty. I thought customer service could have been a bit more considerate as it was out of warranty by a month(?). Hoping I will not have any further issues at this time.
by: Kerwyn09/03/2023
Bolt pattern is perfect. fits my small trailer great.
No more picking out of the dirt!
by: Ray 09/11/2023
Great Replacement Jack. It worked as expected. I would buy this one again.
by: Timothy 10/23/2022
met meneeds
Timothy N.
10/24/2023
it works fine
by: Dave J04/30/2019
Dan
Jack works fine after I made a slight mod to it. When change the position of the stand the level to hold the stand the the position you set, would slam in so tight, you needed a hammer to change it back. I took the level off and drilled a hold in the bend of the level and added a washer and cotter key. works great now. Friend of mine had the same problem, he just drilled the hole a little bigger. I tried to attach a couple picture to this email but not sure if it worked. If you didn't get them let me know and I will forward a email that I sent to myself that has them attached. hope you can understand what I'm trying to say. that's why only 3 stars.
by: James L06/04/2019
It's great to have a heavy duty Jack that makes moving my loaded utility trailer easy to move about. The purchase process was straight forward and smooth. Customer service at etrailer was great, too. The Jack easily mounted and works great.
by: Cynthia 10/16/2023
Haven’t got a chance to use yet. It’s a quality item that will fit our needs.
by: Dan12/07/2022
Jack was easy to install and even easier to use. I’m pleased with this product and haven’t had any issues yet. I installed it on my 10’ long utility trailer.
by: Ralph 09/20/2023
Just got this have not installed yet
by: Kevin 06/25/2023
This jack works very well and is built very well!! I recommend it!!
by: Ralph04/21/2020
I received trailer tongue jack MJ-1206B, and installed it on my new light-duty boat trailer loaded with my 300-lb partially completed boat, but the jack is not yet in full service. There were no instructions included with the delivered package. The online video was helpful, but not a satisfactory replacement for the lack of good written instructions. Thus it is unclear how to lubricate the internal mechanical assembly, and it is unclear whether the main pivot bolt can be/should be tightened to reduce lateral wobble in the loaded jack. Without instructions, some users may have trouble figuring out which of the several provided installation holes to use (at least one user did have this outcome).
In addition, during maneuvering of the trailer on my garage floor, I noticed the wheel was severely dragging, and upon examination I found plastic shavings on the floor. This was the result of the wheel sliding laterally along the pivot bolt (to the outside of the turn) and forcefully contacting the sharp corner of the wheel bracket, which then acted as a “shaver” on the edge of the wheel. The fix is simple: I’ll install spacer washers to prevent the wheel’s sliding, but the manufacturer should have provided such spacers. Due to this defect and the lack of instructions, I am rating this product with 3 stars.
Ralph
4/25/2021
The above fix installation of spacer washers on axle worked. After one year since purchase, the tongue jack has been performing well, without problems. The use has been only occasional since the trailered boat has just now been completed. Tongue weight is light, at about 75 lbs.
by: Tom 02/02/2023
I ordered on a Tuesday morning early and George emailed me and said he caught the order im time to send out that day. I received on Wednesday and installed on the trailer and was back uo and running!
by: Thomas 10/08/2022
Overall a great product.Received less a few mounting parts, but the superior customer service kicked in and it all worked out. Great place for all your trailer needs. First place I go to get my goods.
by: David06/24/2023
Good price, easy install, met my needs
by: Edward10/22/2022
Wheel spins swith cranking up and down, stops the lifing or lowering action of the jack.
by: Steve 06/23/2023
Super quick and accurate delivery.
by: John01/11/2020
A nice, heavy dolly jack. Quality seemed very good. Search as I did, I still came up short one 3/8-16 nut so had to go to the store to get one. I found the main bearing bolt to be very loose. When I attempted to tighten it up it came to what felt like the end of the threads on the bolt and still allowed a bit more slop than I would have liked in the retracted/stowed position. I expect it will rattle in transit but probably get swamped out by all the racket usually associated with the ball/receiver connection.
John C.
1/12/2021
Ive used this retractable dolly for over a year now and it is functioning well. Definitely performing as intended.
by: Foster06/14/2023
Exactly what I ordered and delivered quickly. Nice work!
by: Quincy02/09/2023
Works as intended. Customer service and shipping from etrailer is second to none.
by: Jimmy 06/16/2023
Good Wench
by: William W09/26/2022
Perfect fit , was able to use the old mounting hardware, timely shipping , highly recommend. Thanks , Bill W .
by: Tony P.08/26/2017
Needed a replacement jack for my boat trailer. Although I have ordered from etrailer before and have always found the quality to be very good, I was not expecting much for the price of this jack. Was very surprised when the jack arrived. Very well built! Solid construction. I expect this will be the last jack I need.
Tony P.
8/27/2018
Everything has been good. All the products that I have purchased from you guys are holding up great.
by: Kyle R.09/19/2017
Great trailer jack for the price. Sidewind handle is comfortable to grip and it spins very smoothly with little to no gear noise. The double bushing on the crank are a nice feature not found on many jacks in this price range. Easy installation on my PWC trailer. I have no complaints. Thanks again etrailer.com for a great product.
25
742
Show More Reviews
See what our Experts say about this etrailer Trailer Jack
- Recommended Replacement for a Shelby Trailer Jack Model 5756In order to replace the Shelby Trailer Jack Model 5756 you have on your trailer now, I recommend taking a look at the Round Swivel Marine Jack w/ Wheel part # MJ-1206B. This jack bolts onto a trailer frame up to 4" tall and will not require any welding. It has a zinc plating for corrosion resistance which is ideal for boat trailers and it has a caster wheel for easy maneuvering. There is an integrated swivel feature which operates with a pull pin and the jack can withstand up to 1,000 lbs...
view full answer... - Overall Retracted Length of Round Swivel Marine Jack MJ-1206B I went to our warehouse and measured the Round Swivel Marine Jack # MJ-1206B for the dimension you asked for. When fully retracted, from the bottom of the wheel to the top of the jack tube the overall length of the jack is 23-inches. From the bottom of the wheel to the center of the mounting bracket the dimension is 13-inches. I prepared a photo for you showing these dimensions.
view full answer...
- Swivel Jack Compatible With Malone MicroSport Trailer With 2 Inch Wide x 3 Inch High TongueYes, the Round Swivel Marine Jack # MJ-1206B is compatible with the 2" wide x 3" high tongue on your Malone MicroSport trailer and is going to work well for you.
view full answer... - Does The Location Of The Swivel Jack On The Tongue Or Within The V Matter?The Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs # MJ-1206B can absolutely be installed on the tongue part of the trailer. The video you are referring to I have attached and it wasn't added to the tongue because of the other components that are already present there. If you look at our customer photos you can see this jack can be used on the tongue without issue.
view full answer... - Does Round Swivel Marine Jack MJ-1206B Come With All Mounting HardwareIt does; the mounting hardware for the bracket is included with the bolt-on Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs # MJ-1206B. So you won't need to buy anything else with the # MJ-1206B, it'll be ready to use when you get it.
view full answer... - How Much Does Round Swivel Marine Jack w/Wheel Bolt On Zinc Sidewind 10" Travel 1,000lbs MJ-1206BRound Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs Item # MJ-1206B weighs approximately 15 pounds minus the weight of shipping materials which will be around 1 pound. I have linked a video review of this jack for you.
view full answer... - Overall Stored Length of 1,000 Pound Round Swivel Marine Jack MJ-1206BWhen fully retracted swivel jack # MJ-1206B is approximately 41 inches tall, or long if it is swiveled up. I have included a link to a video review of this jack for you.
view full answer... - How Does etrailer Ram Jack MJ-1206B get LubricatedThere is a hole under where the handle inserts into the etrailer jack part # MJ-1206B which is where you'd spray lithium grease into to lubricate the screw and assembly.
view full answer... - Replacement Options that Work with the Shelby Trailer Jack Mounting Bracket This is a common question people have but unfortunately we do not have nor am I aware of a trailer jack that will work with the mounting bracket you have on your trailer for the Shelby Trailer Jack which includes the Round Swivel Marine Jack w/ Wheel part # MJ-1206B. This jack will be one of the most cost effective replacements we have for you. The welded bracket for your existing trailer jack can be left installed on the frame and you can just place this jack either in front of or behind...
view full answer... - What Is Clearance Between etrailer Swivel Marine Jack Leg And Mounting BracketI went to our warehouse and measured the clearance between the mounting bracket and the leg of the Round Swivel Marine Jack, part # MJ-1206B. That distance is 1-3/4 inches. I have attached a photo of the jack with the dimension noted you can check out.
view full answer...
- Is etrailer.com Round Swivel Marine Jack w/ Wheel Rustproof around Salt WaterThe Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc part # MJ-1206B is designed with a Corrosion-resistant clear zinc finish so it should not rust unless it is submerged for long periods of time or used for prolonged periods of time in salt water without being sprayed with fresh water. I recommend to rinse it off periodically with fresh water to keep away rust.
view full answer... - Comparison of Two Round Swivel Marine Trailer JacksThe two swivel trailer jacks are very similar. The differences are the # MJ-1206B is rated for 1,000 pounds and has 10 inches of travel where the # MJ-1200B is a slight upgrade rated at 1,200 pounds and 11 inches of travel. I've linked videos to each of the jacks for you.
view full answer... - Recommended Trailer Jack With Wheel for 2.5 x 2 Inch Trailer TongueFor your 2.5 inch wide and 2 inch high trailer tongue, the Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 11" Travel - 1,500 lbs # MJ-1500B is my recommendation. It will work very well with the trailer tongue you have and will give you 11 inches of travel from the 13 inch retracted height. I've attached a photo to assist as well as a couple videos.
view full answer...
- Trailer Jack Backup for Atwood Powered A Frame JackSounds like you are looking for a backup manual jack in case your powered A-frame jack fails. For that easiest solution would probably be the # MJ-1206B which you could easily bolt to the frame of the trailer as needed. I attached a review video for this jack for you to check out as well. In case you were looking for a replacement handle for an Atwood jack we no longer can get those parts since they aren't around anymore.
view full answer... - Diameter of Tube that Replacement Cap for etrailer.com and Ram Trailer Jacks FitsThe cap # MJ-1000B-CP is designed to fit MJ-1000B series jacks like # MJ-1206B which has inner tube diameter of 1-3/4 inches. So the cap will fit a 1-3/4 inch tube.
view full answer...
- Replacement Jack with Main Body 20 inches Long or LessWe do have some jacks that will fit the measurements you gave. For instance, we have the Round Swivel Marine Jack w/ Wheel # MJ-1206B which is rated for 1,000 lbs and will retract from 13-1/2 inches and extend to 23-1/2 inches at it max height. If you have preferences as to weight capacity/size/style let me know.
view full answer...
- Swivel Jack that Fits CE Smith Trailer CE48870The Round Swivel Marine Jack w/ Wheel # MJ-1206B works really well on the CE Smith trailer # CE48870 that you mentioned. It's a bolt on install too which means it won't require welding.
view full answer... - Lightweight Trailer Jack with Wheel for Aspen TrailerThe Fulton Snap-Ring Swivel Marine Jack part # F1410050149 will be the best option we can offer you as it has a shipping weight of around 10 lbs or so therefore the actual weight will be more like 8-9 lbs. This will be the lightest bolt-on, swivel trailer jack we offer that comes with a wheel. It measures about 19" long end to end which is also the shortest we offer. If you remove the wheel that could then reduce this by about 6-7" but I am not aware of a swivel jack with a wheel that is...
view full answer... - Swivel Jack Option that Can Fit 2 inch Wide Trailer FrameI have a solution for you but all of the swivel jacks we offer are designed to fit 3 inch wide frames. So what you'd have to do with a jack like the part # DL22800 on your 2 inch wide frame would be to use a 1 inch metal spacer to take up the extra space or just run the nuts down further on the mounting hardware since the bolts are threaded from top to bottom.
view full answer... - Recommended Trailer Jack With Foot for Homemade Utility TrailerFor a jack that is similar to the Round Swivel Marine Jack # MJ-1206B I recommend the Pro Series Round, Snap-Ring Swivel Jack # PS1400300303. This jack has a footplate instead of a wheel and has a 2,000 lb lift capacity. This features a bolt on installation and fits up to a up to 3" x 4" trailer tongue. The jack has an 11" retracted height, 21" extended height, and 10" of lift. The # PS1400300303 is also a swivel jack so you will be able to swing the jack up for travel and back down when...
view full answer... - Recommended Trailer Jack for 1-1/2 Inch Square Tongue On Manure SpreaderFor your 1-1/2 inch square tongue, there is not a custom fit jack. The brackets will allow you to customize for your needs so you will simply need to drill a few holes. I recommend the Pro Series Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,000 lbs # PSEJ10000101 for your application. The snap-ring will allow you to focus on the mounting and then add the jack if desired which is a nice option.
view full answer... - Recommended Jack With Wheel For A 2006 StarCraft Pop-Up Camper And How To Add Brakes To ItIf you're talking about having a trailer jack with a wheel to easily maneuver your trailer around when parking and coupling then I recommend the etrailer Round Swivel Marine Jack w/ Wheel # MJ-1206B. This trailer jack has a bolt-on installation that works with frames 2" to 4" tall. It has a 1,000lb capacity so it's well over the tongue weight of your 2006 StarCraft pop-up camper. It has 10" of travel to help make coupling to your Nissan Pathfinder easier. To add brakes to the trailer...
view full answer...
- Recommended Jack For Log Splitter That Mounts To 2-1/2" Swivel Base With Snap RingI have another option for you, but the Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs # MJ-1206B you were looking at for your Log Splitter does not have a 2.5" swivel base and snap ring, and instead uses a bolt to attach it to the mount. To replace your current jack you will want to go with the Fulton Round, Snap-Ring Swivel Marine Jack - Bolt On - Sidewind - 10" Lift - 1,200 lbs # FTJ12000101 instead. This jack has a 200lb higher load rating than...
view full answer... - Are Replacement Parts Available for Shelby 5854A Trailer JackShelby has been out of business for a number of years now and so there unfortunately are no replacement parts readily available. You might be able to find something where old parts are regularly sold, but you'll probably have to do a lot of digging and it would be much easier to just upgrade your trailer jack now so that when something needs to be replaced in the future it's a lot easier. For a replacement I recommend checking out the Round Swivel Marine Jack w/ Wheel # MJ-1206B rated...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Michael H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Jacob T
Video by:
Kathleen M
Installed by:
Cole B
Installed by:
Randy B
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Mike S
Written by:
Amanda M
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Kirk
8/30/2023
Trailer jack wwheel has worked excellent for the last year. I plan to get another one for our cargo trailer which has a post jack that doesnt retract or swivel and drags on low egress or speed bumps. Another one of these swivel wheel jacks will work just perfect. Thanks etrailer