4" x 2" x 1-15/16". Waterproof LED trailer light illuminates your license plate. Stainless steel mounting base. Durable polycarbonate lens and housing. Surface mount to trailer - hardware not included. Accepts standard 2-prong plug.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we'll be taking a look at the Optronics LED trailer license plate light. This is going to illuminate your license plate on your trailer to make it visible to other drivers, and also to stay within DOT compliance. It's going to be durable housing, polycarbonate lens and housing's also made of that polycarbonate. This is sonically sealed, so that means that the housing and the lens unit are submersible. It's going to work for marine trailers or really any trailer that's going to be out in the elements for a long time. It's going to keep any dirt, water, debris from getting in there and causing issues with your electrical connections.
It should be a long lasting light that we don't have to worry about.We'll have the bracket attached to it. It has two little ears coming off the sides so we can mount this up. It does not come with any hardware for this, so you will have to provide some mounting hardware on your own. But the other nice thing about this light is that it is an LED light. So we'll have longer lasting bulbs.
Not only is it sealed from the elements, but we don't have to worry about any filaments, any brittle bulbs from breaking, and causing issues there. They should last for a long time. Typically LEDs last up to 50 times longer than your typical incandescent bulb. Virtually no maintenance with these.The wiring is just this plug at the back. It accepts an industry standard two prong plug.
I have mine here connected to a power source. Plug those up. There are a lot of options for these two prong plugs available at etrailer.com if you want to pick one up to make wiring your trailer a little bit easier. We turn on that light. See, it's nice and bright.
We'll have our white LEDs to give us that clear illumination. I'm going to turn the lights out here in the studio so you can get a better idea of what it'll look like, an idea of what it'll look like in the dark. It's pretty bright for such a small light. It'll do a good job of illuminating our license plate. So I grab an example here. Set that above my license plate. You can see it illuminates it pretty well.Turn our power source off, and let's take some measurements. The light at its greatest point is about 2 1/4 inches deep. And then the housing is about three inches wide. The ears of our bracket at the widest point is about four inches wide. And that's about two inches tall. The wiring coming off the back is over 12 inches. Let me grab my handy tape measure. And it looks like that wiring coming off the back is about 16 inches long, or excuse me, about 17 inches long. So should be a good amount of length to get that connected up to the rest of your trailer's wiring. We'll have three diodes in there. The power draw at 12 volts is 0.035 amps, so very low power draw. And there is a limited lifetime warranty on the LEDs from Optronics. And that's going to do it for our look at the Optronics LED trailer license plate light.
Average Customer Rating: 4.7 out of 5 stars (12 Customer Reviews)
4" x 2" x 1-15/16". Waterproof LED trailer light illuminates your license plate. Stainless steel mounting base. Durable polycarbonate lens and housing. Surface mount to trailer - hardware not included. Accepts standard 2-prong plug.I just received my lights and have not installed them yet. However, I immediately noticed that the mounting holes in the stainless plate are not centerred in the ears and too close to the light to use bolts. This is something that you can correct easily and should be obvious to you.
Great selection, excellent website, fast delivery. This product should come with at least a mention of the wire color code; both in the web and text and on a small piece of paper in with the shipment. It looks like the lens may come off; if YES it should say how to properly or if NO it should say that so no one tries to open it up and breaks it. It would be good to state how many lumens the LED makes compared to the old incandescent fixture so customers know how much light they will get...more, same, less. as they plan the position of one or more of these based on regulations.
YOU DID A GREAT JOB THANK YOU!!!!!!
great service product was perfect
Great product!
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.