4-7/16" x 1-5/8" Rectangle. Waterproof trailer light serves as either a side marker or clearance light. Red lens with reflex reflector. Surface mount - hardware not included. 2-Pin Deutsch plug. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Surface-mount lights install flat against the surface of the trailer, so a hole does not need to be cut into the trailer for the light. This type of light is installed using a flange or bracket that has mounting holes. And mounting hardware is used to secure the light to the trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're taking a look at the Optronics LED Surface Mount Marker or Clearance Light. This LED Surface Mount Light functions as a marker or clearance light for your trailer. It's a full LED system.LEDs are a great replacements for incandescent lights. They last longer, they burn brighter, and they're much more efficient. You don't have to worry about brittle filaments, and you don't have to worry about replacing bulbs. Optronics actually puts a lifetime warranty on their LEDs.Now this unit features a completely sealed waterproof design.
It's sonically to keep pout any moisture. Feature the really nice, red lens with the built-in reflex reflector, that eliminates the need for a separate reflector. And the wiring, it's a two wire design, so if I pull back the wires here, you'll notice white and black; white for ground, black for power. And then it has the two pin Dutch connector on there, a Dutch plug.Now if you don't want to use that, you can cut that off, strip back the wiring and use it as a hard wire application. It does have protective wire loom that goes over the wires to keep them grouped together safe, and protected from the elements, and it comes with a foam, gasket right here at the back, which would be in between the back of the light and the installation surface.Mounting hardware's not included.
It does have two pre-drilled holes for easy installation, though. Red polycarbonate lens. It's a PT Rated late, it's SAE, and Department of transportation compliant.Now the unit contains a total of three LEDs. The power drill at 12.8 volts is 0.05 amps. Overall length is about 4.5 inches.
Overall hight is 1 5/8. Overall thickness, from front to very back, is about 3/4 inch deep, and then this area right here, which houses the LED circuit board, that has a diameter measurement of about 1, I'm going to say 1 5/16 of an inch to 1 3/8 of an inch.So if you want this to install flush, you'll need to cut out that size of a hole in your trailer to get it to lay flush on the surface.The mount holes on this unit are separated on center by 4 inches. Again, Optronics does cover the unit with a lifetime warranty on the LEDs.Where going to go and hook it up to power, that way you can see what it looks like with power running to it. And then we'll also be able to turn off our overhead light, so you can see it in a low light setting. So you can see here, the light sends out a nice consistent signal.
Again, three diodes, or three LEDs, so the multi-dial design really helps optimize the overall light output. And it does have the built-in reflex reflectors to eliminate the need for a separate reflector.That's going to do it for today's look at the Optronics LED Surface Mount Marker or Clearance Light.
Average Customer Rating: 5.0 out of 5 stars (5 Customer Reviews)
4-7/16" x 1-5/8" Rectangle. Waterproof trailer light serves as either a side marker or clearance light. Red lens with reflex reflector. Surface mount - hardware not included. 2-Pin Deutsch plug. P2 rated.excellent transaction.
Easy transaction, great product and fast delivery.
Using lights to replace motorhome bulb type. As advertised, competitive price and quick delivery.
Thanks!
This was exactly what I was looking for, and at a decent cost.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.