Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Waterproof trailer light kit with (3) 3/4" diameter lights that work as identification lights when properly mounted on trailers over 80" wide. Recessed mount with included grommets. 29" Long insulated wiring harness. PC rated.
Features:
Specs:
The waterproof construction of this light kit makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens of each light are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A PC-rated light produces a 90-degree angle of light to either side of its centerline for a total of 180 degrees of coverage. This beam pattern can be clearly seen when you are standing directly in front of the light, as well as when you are standing on either side of the light. When properly installed, this type of light can function as both a front clearance light and a side marker light or as a rear clearance light and side marker light.
Recessed-mount trailer lights install with a grommet, which is often sold separately. These lights extend past the trailer surface and require a hole for installation. If replacing a light, you can utilize the pre-existing hole. If installing a new light, you will need to cut a hole or use a mounting bracket (sold separately) to complete the installation.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jeff: Hello, everybody. This is Jeff etrailer.com. Today, we're going to take a look at this mini red LED identification light kit for trailers. Now, this trailer light kit will function as rear identification lights for trailers that are over 80 inches wide. Basically, trailers that are over at 80 inches wide, they do require three red identification lights to help define the perimeter of the trailer. Now, these lights are sonically sealed.
They're in a waterproof housing and it makes them submersible. The LEDs are nice because they make great replacements for incandescent lights. They'll last 50 times longer. They're more efficient, they'll provide brighter light with less power output and, of course, no bulbs to replace or brittle filaments to break, and they give you a lifetime warranty on the LEDs. They are durable, polycarbonate lenses and housings.
That is a clear lens you can see, that's over a red LED and these are compatible with 12 volt DC systems.They are a recessed mount, comes with the black grommets right here, and it will require a three quarter inch diameter hole for each light to fit into. It does use a two-wire molded harness, which includes a white ground wire and a black power wire. This is a PC rated light, which produces 180 degree beam pattern, and these are DOT compliant.Again, the application for these are trailers over 80 inches wide. It is for a quantity of three red lights. The lights themselves are three quarter inch diameter and about seven eights of an inch deep.
The harness length on this is about 29 inches and it is one led per light. Power draw at 12.8 volts is 0.022 amps. The last thing I want to do is hook this up to some 12 volt power, just to show you how bright they are. We'll take our two wires, we'll hook up our black power wire, and then we'll hook up our white ground wire. With those both hooked up, you can see the red lights, or LEDs, come on.
I'm going to go ahead and turn off the overhead lights and there you can see, here's your three red LED identification lights. Very bright. Go ahead and turn back on our overhead lights and we'll go ahead and disconnect our power. That should do it for the review on this mini red LED identification light kit for trailers.
Average Customer Rating: 4.7 out of 5 stars (31 Customer Reviews)
Waterproof trailer light kit with (3) 3/4" diameter lights that work as identification lights when properly mounted on trailers over 80" wide. Recessed mount with included grommets. 29" Long insulated wiring harness. PC rated.it was all just as advertised.
Awsum Little lights have been using these lights for years on all my trucks and trailers never replaced any yet,Thanks etrailer
I ordered several different trailer parts from etrailer and the service is good so I won’t order from anyone else. The product is always right
The marker lights were a great replacem ent.
Everything I needed all in one place! Fast shipping.
Excellent sales and knowledgeable empl oyees.
These little guys are great! Easy to install, way bright, adds a little custom touch.
Great item that you have in stock packaged well arrived perfect.
Nice and bright super easy to install
High quality and fast shipping. Customer service was a joy to work with.
Perfect fit good bright light easy to i nstall
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jim
3/17/2022
People are always asking me about these lights. I mounted down behind my tail gate. I used to own big over the road trucks and I was a LED junkie, I had everything led on my trucks as I like bright and long lasting equipment.