Arrives before Christmas 
18" Long. Interior cove lighting strip illuminates a trailer's interior. Great White series features ultra bright white diodes. Molded seal resists dust, moisture, and vapor. Surface screw mount to trailer wall or ceiling. 2-Wire design.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Peterson 18 inch long Great white LED trailer Interior Cove Light. Now this interior cove lighting strip provides a nice bright light to illuminate an interior space. It is perfect for enclosed trailers. It does use molded ceiling to help resist dust, moisture and vapor. It does use 12 white LEDs on it and it is compatible with 12 volt and 24 volt systems. It is a surface mount design.
You can mount it to a trailer wall or ceiling and it can be mounted either horizontally or vertically. And the design of it also, it can fit into corners nicely. Now the mounting hardware to install this is not included. You can see on the end it is a two wire design, includes the white ground wire and the black power wire and the lead length on these wires is about five inches.This part is made in the USA. Light output on this is 1000 lumens.
IP rating is IP 67 and last thing I'm gonna do is give you some dimensions and then we're going to hook it up to some power just to show you how bright it is. So the overall length from the end of the mounting bracket to the other mounting bracket end is 19 11/16th of an inch. They call this an 18 inch light because if you measure right here, the inside of the actual light, it's right at about 18 inches. Now the width on it we're going to do to widths. The widest part is the edge where the mounting brackets are.
That width is going to be 1 3/4 inches. And then width of just the light itself is right at one inch. So what we're going to do now is hook this up to some power.Then we'll go ahead and turn off the overhead lights. So the white wire will be our ground. Black wire will be our power.
And with it all hooked up, we'll go ahead and turn it on and you can see the 12 LEDs all lit up. Go ahead and turn off our overhead lights and you can see for the 12 LEDs gives a very bright light in this whole area, and again, it can be mounted either way, horizontally or vertically. Then turn back on our overhead lights and go ahead and turn off our power. But that should do it for the review on the Peterson 18 inch long, Great White LED Trailer Interior Cove Light.
Average Customer Rating: 4.9 out of 5 stars (71 Customer Reviews)
18" Long. Interior cove lighting strip illuminates a trailer's interior. Great White series features ultra bright white diodes. Molded seal resists dust, moisture, and vapor. Surface screw mount to trailer wall or ceiling. 2-Wire design.
Have actually used used these in different setups. 2 enclosed trailers, a 10' long and 22 ' long. Also used 2 for pickup truck bed lighting mounted under the rails of a tonneau cover.
they have worked very well
Used to replace corroded incandescent back-up lights on trailer, these work great, easy to wire in, great illumination.
Getting ready to put this 2nd set into my trailer. Tied them right into the cheap ceiling lights and really brightened it up inside.
Worked great as a replacement light for my ARE commercial truck topper!
This light was easy to mount and connect. Add a great amount of light
These lights are so nice I just ordered two more to complement the inside of my trailer
Ordered these to add as lights inside my Decked truck bed cargo system. Work great. Note: To wire this up for a Decked cargo box inside light, you can either do a waterproof toggle switch, or go with a magnetic switch like you would use for an alarm system. I did the latter. You can tap into your bed lighting or to a constant 12vdc at the trailer harness. The magnet switches are set so that the lights turn on when I pull a drawer open, and off when I shut it. Attached some photos to show what they look like
Easy to install. Used this to add lighting inside my Decked Drawer system - 2x per drawer.
Worked as advertised and was easy to in stall
The light itself is great! It would work better if there was a deeper recess on the bottom where it mounts to the trailer. This would help conceal the wiring and extend the light toward the rear of the trailer to better illuminate the license plate.
This was a great replacement for the original lic plate light. I did have to drill one new hole because the new light base was a tad wider than the original base. The wiring was very simple: hot and ground and it worked like a champ.
Reordered after breaking on install. It wasn’t the products fault. Someone shut the trailer door on it just prior to final install and broke the lens. Light still works! Quality product!
Very Nice Item
Working great, 1 year later. Perfect fit on my motorhome.
Excellent product and I will buy it again for my next trailer.
Good product, looks good and works well ..
Just received my order in timely manner, can wait to get them installed! Thank you etrailer
Well built, easy installation. Great people to do biz with
Excellent product, much better than the plastic one I replaced. Looks good on my trailer.
Very good bright light. Running for a year now and no issues.
LEDs nice and bright easy to view way better than the traditional incandescent bulbs that were replaced
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.