Female Spade Terminal Quick-Disconnect - 16-14 Gauge - Fully-Insulated PVC - Qty 1

See what our Experts say about this Deka Wiring

• Where Can I Purchase Replacement Spade Terminals
  We do sell a 14-16 gauge replacement for the female and male spade terminal. The part numbers are; Female Spade Terminal Quick-Disconnect - 16-14 Gauge - Fully-Insulated PVC - Qty 1, part # DW01899-1 and Male Spade Terminal Quick-Disconnect - 16-14 Gauge - Fully-Insulated PVC - Qty 1, part # DW01896-1. If the wiring is a different gauge you will have to go to your local hardware store for the replacement covers. I have included product description links below.
  view full answer...
• Does The Curt Soft Trac II Trailer Breakaway Kit Come With A Battery Charger
  Breakaway batteries are typically just wired to the 12v power wire in the trailer's junction box so that the battery can charge while connected to the tow vehicle. The Curt Soft Trac II Trailer Breakaway Kit # C52026 comes with a ground wire already connected to the battery. You can run this directly to the frame with a ring terminal and self-tapping screw. For the power wire you can use some 14ga wire # DW02408-1 and just run it to the junction box on the trailer and connect it to the...
  view full answer...
  
• Installation of Dual Switch on Suburban Brand Water Heater
  You can absolutely install a double switch like the Replacement Double-Panel On/Off Switch for Atwood Gas and Electric Combination Water Heaters - White # AT91230 on your Suburban Water Heater. This switch when wired correctly will allow you to power the gas burner and electric components independently. I've attached a wiring diagram to assist. You may want to use the Female Spade Terminal Quick-Disconnect # DW01899-1, butt connectors # DW05743-5, and Deka Ring Terminals # DW05737-1.
  view full answer...
  
• How to Install Stay-IN-Play Indicator Light on Motorhome for Flat Towing
  There are a few different ways to get the indicator light from the Demco SBS Stay-IN-Play DUO Supplemental Braking System # SM99251 operating in your motorhome. If you don't plan on using the brake controller circuit on your motorhome then you can connect the indicator to your motorhome by using that circuit. Tap in a wire from the stop light circuit on your towed vehicle to the connector at the front of your towed, making sure it corresponds to the brake controller pin on your motorhome...
  view full answer...
• How is Motor Mounted to Ventline Ventadome Trailer Vent V2094
  You are correct, the Replacement 12V DC Motor # BVD0218-00 is mounted via screws which are underneath the fan blade (see accompanying photo), which is Replacement Fan Blade # BVD0215-00 for the Ventline Ventadome Trailer Roof Vent # V2094SP-30 (you will need this fan as well if you are replacing the motor on a fan which was manufactured before 2002. In regards to the spade connectors, you are right on the money as that is what is used with the switch. You can see that in the linked video...
  view full answer...
  
• Spade Terminal Size on Mini-Illuminated 12V Switch 12765
  The Mini-Illuminated 12V Switch part # 37212765 uses standard 3/16" or .187" spade terminals. We offer these for 16-14 gauge wires as the Female Spade Terminal Quick-Disconnect part # DW01899-1.
  view full answer...
• Can In/Out LED Rocker Switch be Used for any Winch
  You should be able to use the In/Out LED Rocker Switch For Bulldog Winch # BDW20261 for your winch. If you take a look at the linked video you can see this switch being installed if you forward to about the 10:00 mark. You do need to make sure it is wired correctly and I have added the diagram Bulldog has provided to help. It is grainy but says 1: Winch Power Out, 2: Power 12V, 3: Winch Power In, 7: Ground. You will need to use Primary Wire - 16-Gauge # 16-1-1 and Spade Terminals # DW01899-1.
  view full answer...
  
• Components Needed to Extend Length of Wiring That Powers Ventline Powered Vent Fan
  To extend the length of the wiring that powers your Ventline vent fan you can use 2 of part # DW01899-1, which is a Female Spade Terminal Quick-Disconnect, 2 butt connectors # DW05714 and a suitable length of 2-conductor wire such as # 12-2-1 (which is sold by the foot). The wiring portion of part # BVD0218-00 is not sold by itself.
  view full answer...
• Availability of Wiring Splitter to Connect 2-Pin Lighted Hitch Cover to Brake Light Circuit
  It sounds like you have a lighted hitch cover that features a 2-pin connector that is designed to plug right into a 4-Way on the vehicle, similar to the plug end of the GMC # CR-007G. We do not currently have a splitter available that will plug into this harness and provide you with a single 12V lead wire. If you don't want to or cannot plug into a 4-Way on your Sienna, your best option may be to simply cut off the plug end and use some Quick-Disconnect Spade Terminals like # DW01899-1...
  view full answer...
• Wiring An Atwood RV Water Heater With Double-Panel On/Off Switch
  The manual for the Double-Panel On/Off Switch for Dometic Gas / Electric Combination Water Heaters - White # AT91230 lists the wire as orange but the manual for Atwood water heaters like AT94022 list the wire as red. It's referring to the wires that come out of the top of the unit. The three dash symbol you're referring to means ground. The blue wire will connect to terminal 6 of the switch. Terminal 4 of the switch will go to the negative battery terminal. The green wire will connect...
  view full answer...
  
• Determining The Correct Size Spade Terminal Connector For The Triple Rocker Switch # 37212025
  To connect to the Triple Rocker Switch # 37212025 you'll need a 1/4" female spade terminal connector and will need to know the gauge of the wire you're connecting to the switch. For example, the Female Spade Terminal Quick-Disconnect # DW01899-1 would connect to the pins on the switch and crimps onto 14 - 16 gauge wire. For 10 - 12 gauge wire or if you're splicing multiple wires to one connector then you could go with a larger gauge option like the # RM-300115-00.
  view full answer...
• Will the Universal-Design Rocker Switch With Dual Actuators Install In a Standard Switch Cutout
  The Universal-Design Rocker Switch part # PK34312 is a dual actuated switch that gets installed in a 0.830" wide x 1.450" tall cutout which is a very common size. Therefore, yes the above will install inside a standard 12 volt rocker switch cutout. For reference, the Universal-Design Rocker Switch part # PK34360 is a single actuated switch that gets installed in the same 0.830" wide x 1.450" tall cutout as the above. The Female Spade Terminal Quick-Disconnect part # DW01899-1 is what...
  view full answer...
• How to Turn Off Back-Up Alarm of Curt C57100 When Not Towing
  Once the Curt # C57100 is installed, the alarm will sound every time you put the transmission in reverse, regardless of whether or not you're towing at the time. The only way I can think of to defeat the alarm for when you're not towing would be to install a switch like # PK34308 inline on the wire feeding the reverse lamp circuit to the # C57100. You'd need to peel back the tape or wire loom that covers the factory wiring harness the C57100 plugs into. Use a circuit tester like # PTW2993...
  view full answer...
  
• Is There a Class II Trailer Hitch Receiver Available for a 2008 Chrysler Sebring Convertible
  The only trailer hitch receiver option for your 2008 Chrysler Sebring Convertible is the Draw-Tite Sportframe # 24871, which is only a Class I hitch. Due to the design of your Sebring, there are no Class II options available. This trailer hitch has a Gross Trailer Weight (GTW) of 2,000 lbs and a Tongue Weight (TW) of 200 lbs. I checked an online version of a manual for you Sebring and if had the same weight capacities that this hitch has, but you will want to check your copy of the owner's...
  view full answer...
• Recommended Wiring Connectors To Avoid Soldering with Replacement Switch for Husky Brute Jack
  If you don't wish to solder the wires onto your replacement switch, you can use the Female Spade Terminal Quick-Disconnects like # DW01899-1 to give you quick connections you can crimp onto the wires.
  view full answer...
• Recommended Trailer Hitch Receiver for 2013 Audi Q7
  For your 2013 Audi Q7, I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75950 over the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13220 because it requires a stability strap # 18050 for any non-trailer loads like bike racks and cargo carriers. The attached installation details do not state trimming is required for your model vehicle. If you will be towing or using a lighted accessory, I recommend the Curt Powered Tail Light Converter...
  view full answer...
• How to Install the On/Off Switch Panel for Atwood Gas and Electric Water Heaters Part # AT91230
  I have attached the wiring diagram for the Replacement Double-Panel On/Off Switch for Atwood Gas and Electric Combination Water Heaters part # AT91230. The installation will be very simply with only 5 connections needed. There will be three terminals that go to the water heater (orange, blue, white), one terminal that goes to a 12 volt power source, and one terminal that goes to a ground. In order to make these connections I recommend using four of the Female Spade Terminal Quick-Disconnect...
  view full answer...
  
• How To Wire Up 4-Pin In/Out LED Rocker Switch
  When wiring the In/Out LED Rocker Switch # BDW20261 you will have two pins being your power and ground. Then the bottom two are going to be your in and out pins which will connect to your universal solenoid. For ground, just take a self tapper and connect it to the frame somewhere. The power I would use a fuse tap # F2526 to tap into your ignition fuse in your control panel. Which if you don't already have them, we have spade connectors # DW01899-1 and wiring # 16-1-1 if you needed it. This...
  view full answer...
• Replacement Headlight Housings and Bulbs for 1996 Pontiac Trans Am
  As long as your 1996 Pontiac Trans Am features 4 inch x 6 inch rectangular sealed lights, the Vision X Headlight Conversion Kit # VX-46 that you were looking at should work well as a replacement. These housings do not come with the needed 9007 bulb but it can be added with # VX-L9007. You will just need to cut off your existing headlight bulbs pigtail and wire it to the harness included with the housing using some quick-disconnects like # DW01899-1. These halogen lights feature multi-surface...
  view full answer...
• Locating Brake Stop Lamp Signal to Install Brake Controller on 1998 Chevy C/K Series Pickup
  You wouldn't be able to access the brake lamp signal at the trailer connector because the right turn and left turn lamp circuit also carries the brake lamp circuit. This could cause the trailer brakes to apply when you use the turn signals. The brake switch is very hard to access in these trucks, because of the under-dash bracing that's in the way. You have two options. You can access the brake signal from the circuit feeding the third brake lamp, or you can try to access it at the junction...
  view full answer...
  
• How To Attach Reverse Light Wiring For Putco Universal LED Tailgate Light Bar On 2017 Toyota Tundra
  The Putco Blade Universal LED Tailgate Light Bar # P92009-60 does plug into your 4-way trailer connector on your 2017 Tundra. That will take care of the stop, tail, and turn signals for the light bar. To get the backup lights working you will need to attach the White wire to the reverse light circuit on your Tundra. You can use the quick-disconnects like part # DW01899-1 and part # DW01896-1 for the reverse light wire. For 16 gauge wire you can use part # DW02359-1. This is sold by the foot.
  view full answer...
• Installing LaSalle Step Heaters On A School/Commercial Bus
  I talked to the LaSalle, the manufacturer, and they said that you should be fine using the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat - 18-1/4" Long x 12" Wide Item # 277-000164 between metal and the rubber step tread on a school/commercial bus. To install these pads you'll need the following items to complete wiring to the battery/installing a switch: Switch: Universal-Design Rocker Switch - SPST - On-Off - 12 Volt - 20 Amp - 4-Blade - Red Pilot Light Item # PK34310 Spade...
  view full answer...
• Breakaway Battery With F1 Terminals and Box
  Good News! the Curt # C52023 battery has F1 Posts. If you must have F1 size terminal connectors you can find them online be searching for: 0.032" x 0.187" Female Terminals. Usually a standard 16-14 gauge connector like the Deka # DW01899-1 will fit just fine. For a battery case I would recommend the Tekonsha # TK2018 box. It is water tight and has several mounting choices.
  view full answer...
• How to Use the Vision X Headlight Conversion Kit Part # VX-46 on a 1986 Ford F-Series Truck
  The Vision X Headlight Conversion Kit part # VX-46 is a headlight housing and does not come with the headlight bulb. You can add the headlight bulbs to this housing using part # VX-L9007. You would need cut off your existing headlight bulbs pigtail and wire it to the harness included with the housing using part # DW01899-1. You will need 6 of the spade terminals in order to wire the new harness. If your 1986 Ford F-Series truck uses a 9007 headlight bulb then you will not need to use the...
  view full answer...

Do you have a question about this Wiring?