Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID

See what our Experts say about this Fastenal Wiring

• New Side Marker trailer Lights are Very Dim
  It sounds like a bad ground connection. Ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use another function like a turn signal or brake light. But can also appear when changing out lights. Make sure that the vehicle side and trailer side connectors are clean and free of corrosion inside and out. The main connector grounds should be attached to clean and corrosion free bare metal surfaces. The light grounds should...
  view full answer...
• How Many Ring Terminals Are Included with Fastenal # 44-5310A
  Yes, the listed price for the Fastenal # 44-5310A is for 1 ring terminal. This is designed for use with 12-10 gauge wire and features a 3/16 inch stud. I have attached a short video review that you can check out as well.
  view full answer...
• Wiring for Lights Using Junction Box # 38656
  If you take a look at the photos I've attached you can see how the wires from a 7-way connector can be run to junction box # 38656. You would also need ring terminals # 44-5310A. I've added a link to a video review, as well as an install of this junction box for you to take a look at.
  view full answer...
  
• Junction Box Terminal Post Size for Part # 3375601100
  The ring terminals you want to use with the junction # 3375601100 are the # 44-5310A which have an inner diameter of 3/16 of an inch.
  view full answer...
• What Size Ring Terminals Should be Used with Buyers Products Junction Box # 3375601101
  The ring terminal size you need for the posts of the junction box part # 3375601101 that you referenced is 3/16 inch like the part # 44-5310A which would work great. The terminal matches the correct ring size and also is designed for 10 to 12 gauge wire.
  view full answer...
• Diameter of Terminals on Spectro Trailer Wiring Junction Box
  The Trailer Wiring Junction Box # 38656 referenced in your question features 3/16 inch outer diameter terminals that will work perfectly with ring terminals like # 44-5310A. This junction box will provide a fast and easy way to connect the wires from your trailer connector to the wiring for your 6-Way or 7-Way connector. I have attached a short installation video on this product that you can also use for reference.
  view full answer...
• Parts Needed to Re-Wire Tandem Axle Gooseneck Trailer for 7-Way Type Operation
  We can help you re-wire your tandem axle gooseneck trailer to have a 7-way plug to match your tow vehicle. Have a look at the linked article on trailer wiring. Typically a white wire is used for ground. There are several ways a 7-way can be wired so you will want to ensure that each circuit on the vehicle socket is correctly matched to the appropriate circuit wiring on the trailer. Testing the trailer light functions with a spare 12V battery can make this identification easier. You can...
  view full answer...
• Ring Terminal Recommendation for Use on Junction Box 277-000141
  The ring terminal size you want to use on the posts of the junction box part # 277-000141 is 3/16 inch like the part # 44-5310A which also fits 10-12 gauge wire.
  view full answer...
• How to Make Ground Connection When Mounting Kat's Heaters Defrost Fan to Wooden Surface
  The Kat's Heaters Defrost Fan # KH43100 that you referenced does indeed ground via its mounting screws. If you plan on mounting the fan to a wooden surface then you will just need to run a separate ground wire from the bolt using a ring terminal like # 44-5310A to a nearby metal surface or to the negative post on the battery you're using.
  view full answer...
• What Size Ring Terminal Will Fit the Hidden Hitch Wiring Junction Box # 38656
  I pulled the Trailer Wiring Junction Box # 38656, and Ring Terminal # 44-5310A, from our warehouse. The correct ring terminal size that will fit is part # 44-5310A, which is a 3/16 ID terminal for 12-10 gauge wire. I produced a short video showing that the # 44-5310A ring terminal fits on the post of the Junction Box. Also linked is an FAQ on trailer wiring.
  view full answer...
• What Size Ring Terminals Needed For Epicord 277-000141 Trailer Plug With Junction Box
  For a tidy, professional installation, using a junction box like what's provided with # 277-000141 is without a doubt the way to go. You'll want to use 3/16 inch ring terminals like # 44-5310A. I've linked to an installation video you might find helpful.
  view full answer...
• Recommended 7-Way Wiring Harness For 2000 Sundowner Horse Trailer And 2013 GMC Sierra 3500 Dually
  For your application, I can absolutely give you the wiring function locations. I've attached a picture to assist. Based on what you mentioned, I think I have a better option for you. I recommend the Epicord 7-Way Molded Trailer Plug with Junction Box - 10' Long # 277-000141. This will allow you to connect your wiring at a junction box using the ring terminals like # 44-5310A, and then uses a molded plug so you won't have the disconnection issues as you plug and unplug your 2000 Sundowner...
  view full answer...
  
• Trailer Junction Box Installation on Trailer to Avoid Use of Wiring Adapters
  Sometimes trailer wiring adapters do cause odd behavior from vehicle lights, trailer lights or both. It is often better to do an actual re-wiring of the trailer to match the vehicle's connector so that adapter complications are avoided. Fewer connections are also generally more reliable. A 7-way junction box like # e99011 mounts to your trailer frame and it comes with a 7 way cord. Simply cut off the existing trailer 4-pole connector and apply ring terminals like # 44-5310A to the trailer's...
  view full answer...
• Junction Box To Wire Lighting on Flatbed Trailer
  Yes, the Pollak 10-Terminal Junction Box part # PK52248 will work to wire up the lights on your flat bed trailer. The posts on this particular junction box are not labeled so you can connect your functions to the box on any of the posts. Since you are just doing lights, you can just leave the rest of the posts unused without any issues. You will need ring terminals part # 44-5310A to connect your wiring to the terminals.
  view full answer...
• Where To Connect The Ground Wiring From The 4 Pole Connector # 18004 On My Trailer
  When installing The 4-Pole Trailer End Connector # 18004 the easiest way to attach the ground wire would be to attach the white wire to a clean, bare metal surface on the vehicle with a self tapping screw # 101131802, and adding a ring terimal # 44-5310A. A good ground location would be on the trailer frame or sheet metal that is not painted. I attached a review video link below.
  view full answer...
• How Do I Ground the Yellow Wire to Pair/Sync My Remote with Air Lift WirelessONE Compressor
  Grounding an electrical wire, which is all this is, entails finding a paint and corrosion free spot on the frame of the vehicle that you can connect the wire to. You'll likely want to use a ring terminal like the # 44-5310A and a self tapping screw of some sort to complete the connection to the frame and allow for grounding the circuit. The steps for pairing the remote are listed below for you to use as a reference in the event that you want a quick place to refer back to. 1. Turn ignition...
  view full answer...
• Troubleshooting 7-Way Trailer Wiring with Colors That Don't Match Functions
  Wiring by function is the route to go for your situation. This is done by testing each wire of your trailer individually. The easiest way is to use a 12V battery and connect the negative terminal to the trailer's ground on the frame and then use the positive terminal with a jump wire to connect to each individual wire. One wire in your 7-way will be the ground wire. You will want to find this one first because it will cause a spark if you connect the battery to it. You can trace...
  view full answer...
  
• How to Install Trailer Wiring Junction Box 38656 on 2014 Wilderness Travel Trailer
  The Trailer Wiring Junction Box # 38656 that you referenced is a general-purpose wiring box that is not specific to any type, brand or model of trailer so it definitely can be used on your 2014 Wilderness camper to make new wiring connections. This junction box is set up for a 7-way wiring configuration but it could still be used on a trailer that has more basic 4-pole wiring. The box allows you to make solid and stable wiring connections between the lights on your trailer (and brakes...
  view full answer...
• Troubleshooting Trailer Brakes That Show Intermittent Overload Error Message on Prodigy Controller
  It sounds like your Prodigy brake controller in your 2004 Dodge Ram Pickup is sensing an intermitting short in the trailer wiring. Since you have checked the brake magnets and have found them to be okay, I suggest tracing the entire brake circuit for signs of damage or corrosion. Follow the brake circuit wiring from each brake all the way to the trailer plug. Look for cracked insulation and spots where it is worn off, especially near points where the wire bends and where it comes into...
  view full answer...
• What Circuit Breaker is Needed for a 2011 Chevrolet Silverado with Tekonsha Brake Controller
  The correct size circuit breaker for the Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 installed on your 2011 Chevrolet Silverado will vary depending on the number of braked axles your trailer has. Since you only have one braked axle then you are going to want to use a 20 amp circuit part # 9506P. The black 12 volt wire from the brake controller will need to be attached to the silver "AUX" terminal on the circuit breaker and the copper "BAT" terminal will need to be attached...
  view full answer...
• How to Upgrade 6-Way Trailer to 7-Way to Match Connector on 2014 Dodge Ram 1500 Pickup
  The best way to help your Ram pickup with a 7-way to get along with your 6-way-equipped trailer is to upgrade the trailer to a 7-way. This is a simple process of installing a 7-way plug like # H20046 with a junction box # 38656 and ring terminals # 44-5310A. All you need to do is apply 12V power to each trailer wire to confirm its function and then install each wire in the junction box at the appropriate terminal. Although adapters do exist, they can be tricky to use since a 6-way can...
  view full answer...
• Troubleshooting Trailer Side Wiring Connection With Smaller Holes
  I'm glad the new Hopkins 7-way was an easy installation. The apparent difference in size of the connector on your trailer is odd as the blades and corresponding connections are industry standard size. It is possible that your trailer doesn't have the industry standard connector, but that would be odd. The only other thing that would cause a connector to not fit is if there is corrosion built up on the inside of the trailer wiring connector. You may want to take a look at that possibility...
  view full answer...
• How to Install New H20046 Trailer Connector and Tie In to Existing Wiring
  I'd be glad to help you out with that. Your trailer wiring sends one leg of the running lamp circuit down each side of the trailer, rather than one leg down one side that daisy chains over to the other lamp. Simply take both brown wires and connect them to the running lamp circuit wire from the trailer connector you're using. If you're using the # H20046 connector, pay attention to the color coding chart shown on the product page, as the color coding is different. This connector uses the...
  view full answer...
• Recommended Junction Box for 7-Way Trailer Connector
  To purchase just the junction box you will want item # 38656. It is made by Spectro. This box is weather proof, but not water proof, and what that means is that it will keep water out under normal circumstances rain and puddles, but if it were to be submerged the box would not stay dry on the inside. I have linked an installation video below. You will also want the Ring Terminal item # 44-5310A to complete your installation.
  view full answer...

Do you have a question about this Wiring?