Self-Stripping Connector with Waterproof Sealant - 14-18 Gauge - White and Blue - Qty 1

See what our Experts say about this Spectro Wiring

• Connector For Attaching T-One Vehicle Wiring Harness # TK35VR To Power Connector 2022 Tesla Model 3
  Yes, the T-One Vehicle Wiring Harness # TK35VR is confirmed to fit on your 2022 Tesla Model 3. While we do not have a separate connector like the one included with Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit # 391TES317T you found on Youtube. You can use a Self-Stripping Connector # SWC501746-1 to tie into the wiring behind the connector as long as you do have the connector on your Tesla. Not all the Model 3's have this connector so you will want to verify to determine if...
  view full answer...
• Converting 4-Way of 2001 Toyota Tundra to 5-Way to Tow Boat Trailer with Surge Brakes
  We have a solution to convert your 4-way to a 5-way so that your reverse lockout solenoid can activate but we don't have a plug and play style of adapter. Instead your best option is a 4-way to 5-way adapter part # 20036 which plugs into your current 4-way and then gives you an additional wire you'd run to the reverse light circuit of your truck. You can use a quick splice connector part # SWC501746-1 to tap into the circuit easily.
  view full answer...
• Installing Yellow Wire of Curt C57674 Adapter for Trailer Reverse Lockout on Surge Coupler
  The reverse lamps for the 2021 Toyota Highlander are in the liftgate, so the best bet would be to find the harness feeding the taillights and use a circuit tester like # PTW2993. Unfortunately, I don't have specifics on where the harness is located or the wire colors, but this is pretty easy to figure out. The harness typically runs behind the bulkheads in the cargo area and will usually run up to the top of the liftgate in the pillar next to it. Once you locate the harness, the first...
  view full answer...
• 4-Way Trailer Wiring Extension Recommendation to Allow Flat Towed Vehicle & Trailer Behind Vehicle
  What you'll need is a long 4-way extension spliced into the 4-way you have at the back of the RV. For that you'd want to use the part # HM48235 which is 120 inches long. You'd need to cut off the one end and then use quick splice connectors like # SWC501746-1 to connect to the RV wiring. This will allow the 4-way to operate the CR-V taillights and then you'd be able to route the jumper wire to the back of the CR-V where you can then plug it into your trailer.
  view full answer...
• Availability of Waterproof Connector for Side Marker Light Wiring on Boat Trailer
  In order to splice into the wire and add yellow side marker lights like the # MCL13A2B I recommend using the Self-Stripping Connector with Waterproof Sealant # SWC501746-1. This is designed to make a quick connection without cutting or stripping, and uses a waterproof sealant to help prevent corrosion. It is designed for marine use. I would also recommend wrapping the connection in electrical tape for extra protection.
  view full answer...
• Can a Third Brake Light Be Added to a Trailer
  To add a third brake light to a trailer is pretty simple, but does require an adapter to convert the signal. Because trailer tail light systems combine the stop lamp and turn signals for each side onto a single circuit, you will need to use a vehicle-to-vehicle tail light converter, part # 118158 to split the brake light circuit back out. The white wire on the input side of the converter would ground to the trailer frame, the green input wire would tap into the right turn circuit on...
  view full answer...
  
• What's Needed To Add Reverse Light Function To Curt Adapter 57676 On 2021 Kia Telluride?
  You've got it. You'll need to run some # 16-1-1 from the blue wire on the Curt 4-way to 7-way adapter # C96KR (57676) to the reverse light circuit on your 2021 Kia Telluride. A circuit tester like # PTW2993 will help you to find the correct wire to splice into with a quick splice # SWC501746-1.
  view full answer...
• How to Activate Reverse Light Circuit of 7-Way Adapter part # 37185
  In most situations a reverse light circuit isn't needed when using the 4-way to 7-way adapter part # 37185. But if you do need to activate this circuit you'll want to run the purple wire of the adapter to the reverse light circuit of the vehicle and use a quick splice like # SWC501746-1 to tap into it and you'd be set. You'd need to use a circuit tester like part # PTW2993 to test the wires that run to the reverse light to find the correct wire to use.
  view full answer...
• Wiring Reverse Light Circuit to 7 Way Connector on 2016 GMC Terrain
  The center pin of a 7-way is typically the reverse light circuit. You'd need to tap into the reverse light circuit of your 2016 GMC Terrain to activate it. For a quick splice for 14-18 gauge wire you'd want # SWC501746-1 or for 10-12 gauge wire # SWC501915-1. I'd recommend strongly that you run the 12 volt power wire back to the positive post of the battery and not to a 12 volt outlet to prevent shorting out that circuit.
  view full answer...
  
• Recommended Wiring and Lights for Utility Trailer
  I'm assuming you want to replace everything here so I will start off with a 4-way. I recommend using the Hopkins Endurance 4-Way Flat Trailer Wiring Harness - 30' Long # HM48265. This will give you a lot of wire to work with so you can hook up all of your lights. This uses your typical 18 gauge wire for the lights and 16 gauge for the ground. If you need additional wire you can use the # SWC97FR or # DW02923-1. You could use the Self-Stripping Connector with Waterproof Sealant - 14-18...
  view full answer...
• Do All 7 Circuits of 7-Way Need to be Ran When Installing Brake Controller
  So the first thing you should note is that if you don't need a reverse light circuit or an accessory circuit you don't have to complete those wires. You can leave those off for most situations. Normally the 12 volt power wire runs to the positive post of the vehicle battery with 10 gauge wire like part # 10-1-1 (sold by the foot) through a breaker like part # 9510 and then the reverse light circuit runs to the reverse lights of the vehicle tapped in with a quick splice like part # SWC501746-1....
  view full answer...
• Wiring Location to Connect a Brake Controller to a 2017 GMC Acadia
  The stop light switch wiring is located behind your brake pedal on your 2017 GMC Acadia. See the picture for a visual. If you are having trouble locating the wire you can use a Circuit Tester # PTW2993 to find out which wire sends a signal when the brake is depressed. You can use a Quick Splice Wire Connector # SWC501746-1 or a Butt Connector # DW05714 to connect the red wire from your brake controller to the stop light switch wire on your Acadia.
  view full answer...
  
• Recommended Quick Splice Connector To Install Truck Bed Cargo Camera 3460010
  The Self-Stripping Connector with Waterproof Sealant part # SWC501746-1 can be used in place of the Quick Splice Wire Connector part 564 (No Longer Available) to install the Truck Bed Cargo Camera for 8" Factory Monitor part # 3460010 on your 2015 Chevrolet Silverado 2500. They are the same save for the water seal on the former.
  view full answer...
• Turn Signals On 2019 Ford F-350 Flat Bed Still Flash with Load Resistors Installed
  The two most common issues with resistors like part # DI34ZR are incorrect installation and the quick splice connectors not having enough contact with the circuit. I have attached for you below the correct wiring diagram for a load resistor but make sure you have the correct wires beforehand by testing with a circuit tester. The quick splice connectors included with most resistors are not of the best quality so I think you will have much better success with part # SWC501746-1. When installing...
  view full answer...
  
• How to Wire a 7-Way Trailer Connector on a 1999 Chevrolet S-10 Pickup
  In order to install a 7-way trailer connector on your 1999 Chevrolet S-10 Pickup you will want to use the Adapter 4-Pole to 7-Pole and 4-Pole part # 37185. This adapter will plug into the 4-way trailer connector you have on your vehicle and will give you both 4 and 7-way trailer connection points. Since you boat trailer only uses 5 of the 7 wires on the trailer connector, the only 2 wires you will need to attach on the 7-way is the ground and reverse light circuit. In order find the reverse...
  view full answer...
• Adding 4-Way To Rear of Trailer for Towing Second Trailer
  To add a 4-way to the rear of your trailer will require you to hardwire a 4-way to the taillight circuits of the trailer. For that you would want the part # A35W42B which is a 42 inch long harness that would allow you to tap into the wires of your trailer circuits with quick splices like the # SWC501746-1. It might be easiest to run all of the circuits from your first trailer to a junction box like part # 38656 and then run the additional 4-way from that to your second trailer. I attached...
  view full answer...
• Recommended Trailer Wiring Harness for a Boat Trailer
  The Optronics 25 foot 4 Way Wire Harness # A25W2GWB will be a good option. This will generally have enough length to cover most trailers. I will also recommend adding in a few of the Spectro Self-Stripping Connector with Waterproof Sealant # SWC501746-1. These will make splicing into the # A25W2GWB significantly easier. Especially for your side marker lights.
  view full answer...
• How to Add a Third Brake Light to a Trailer
  To add a third brake light to a trailer is pretty simple, but does require an adapter to convert the signal. Because trailer tail light systems combine the stop lamp and turn signals for each side onto a single circuit, you will need to use a vehicle-to-vehicle tail light converter, part # 118158 to split the brake light circuit back out. The white wire on the input side of the converter would ground to the trailer frame, the green input wire would tap into the right turn circuit on...
  view full answer...
  
• How to Wire Up the Rampage SuperBrite LED Tailgate Light Bar # RA960137 to Reverse Light Circuit
  What you will need to do is find the wiring harness that runs to your 1995 GMC Sierra's taillights and then using a circuit tester like part # PTW2993 test all of those wires till you find one that has voltage when the vehicle is put in reverse. Once you find the correct wire you will then attach the white wire of the # RA960137 to it using a quick splice connector like part # SWC501746-1 and the light will activate properly when put in reverse.
  view full answer...
• Recommended 7-Way Trailer Wiring Harness To Install On Trailer
  The Pollak 7-Pole, RV-Style Trailer Connector Socket w/ Wiring Harness and Mounting Bracket part # PK11898 is what I recommend that you use on the back of your trailer in order to install a 7-way as it comes with the trailer connector, wiring harness, mounting bracket, and the hardware to connect the mounting bracket. The wire connectors however will need to be swapped out with part # SWC501746-1. You are correct in that you will need to splice into the tail lights on your trailer in order...
  view full answer...
• What is Purpose of Fifth Circuit Of Trailer Wiring that Runs to Reverse Light Circuit
  The circuit for the trailer is what allows your trailer to be backed up without the brakes locking up. When that circuit is active it prevents the surge brake actuator from being able to build pressure and activate the brakes. You want to have it connected to your reverse light circuit on your truck. On the tailgate/rear door you'll need to look for a rubber grommet with that has wires in it. In that wiring bundle will be a circuit that carries the reverse light circuit. Tap into it with...
  view full answer...
• Can 2 Hopkins Smart Hitch Backup Cameras be Installed on a 2003 Ford Focus
  There is no easy way to wire two cameras to one monitor in the Hopkins Smart Hitch backup camera # HM50002. To avoid voiding the warranty I would not put the monitor power wires on a switch either; rather you could just switch which one is plugged in at the time. For the front one I recommend wiring it to the running light circuit on the vehicle. Then when you turn on the vehicle lights the camera will turn on. You could potentially use a quick spice connector # SWC501746-1 to splice the...
  view full answer...
• Installing The Fusion LED Trailer Light # STL211XRFHB On A 2009 Chevrolet Silverado 1500
  The Fusion LED Trailer Light # STL211XRFHB will work on your 2009 Chevrolet Silverado 1500. When installing The Fusion LED Trailer Light # STL211XRFHB on your 2009 Chevrolet Silverado 1500 I recommend using The Deka Bonded 4 Wire # 16-4B-1 which is sold by the foot. Then you can use the Butt Connectors # DW05744-10 and the Quick Splice Wire Connectors # SWC501746-1 to connect the wiring to the appropriate functions. The Fusion LED Trailer Light pigtail wiring will connect to your Silverado's...
  view full answer...

Do you have a question about this Wiring?