bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Coachmen RV and Camper Steps


  • Differences Between MORryde StepAbove Fold-Down Steps MR98RR and MR48RR
  • You are right on. The 8" rise/drop on the MORryde StepAbove Fold-Down Steps # MR98RR is the height between the steps. The # MR48RR you were looking at has a 9" rise/drop meaning the distance between the steps is 9". The # MR98RR is designed for RVs with a 23-3/4" - 26-1/4" wide door frame, and requires and entry height between 30" - 33-1/2", and the # MR48RR is designed for RVs with the same 23-3/4" - 26-1/4" wide door frame, but is used when the entry height is between 34" - 36". Entry...
    view full answer...

  • Lippert SolidStep Fit for 28 Inch Wide Door and 38 Inch Entry Height
  • The best Lippert SolidStep for you RV with a door frame that measures 28 inches and an entry height of 38 inches is the SolidStep Manual Fold-Down Steps for 26" to 29-7/8" RV Door Frames # LC791574, which, as you can see by the name of the product, is perfect for your 28 inch door frame. It is also designed to fit entry heights between 35 inches and 44 inches, which it can do because it has adjustable let extensions. These steps do not come with mounting hardware but you will only need...
    view full answer...

  • Installation Bracket Locations for Lippert Victory Fold-Down Steps
  • The Victory Step Manual Fold-Down Steps for RV and Toy Hauler Patios - Quadruple - Aluminum # LC726895 you asked about will only allow for about 3 inches from the edge. For your application you would either need to add a piece that is hinged to flip out over the door frame or add a piece to the outer door frame to hold the brackets and weight. This could look similar to the Lippert Components Garage Storage Brackets for Victory Step Manual Fold-Down RV Steps - Wall Mount # LC726890 but...
    view full answer...

  • MORryde StepAbove Fold-Down Steps for 2018 Montana Fifth Wheel
  • Since the distance from your threshold to the ground is 38", and the narrowest part of your door is 28-1/4" side-to-side, the MORryde steps that are a fit for you are the MORryde # MR28RR steps featuring 8" deep steps. Optionally you could also use the MORryde # MR85RR steps which are the same as the MR28RR's except they feature gas lift struts that allow you to lift of lower the steps with one finger! If these steps are replacing traditional fold in steps you should consider the...
    view full answer...

  • Will Screen Door and Entry Door Close Normally with SolidSteps in Place?
  • When the Lippert # LC791572 steps are properly installed with the threshold plate firmly against the outside threshold you should have no issues. The only thing we hear from customers is how much they love them! While you have your tools out you might as well take down those old stock rattle-trap steps that came stock on your trailer and install the Lippert # LC664640 locking steel box just made to fit in the spot where the steps were. Great spot for black water supplies, or roadside...
    view full answer...

  • Fold Out Camper Steps for 24" Wide Door and 27"-36" Entry Height
  • The Lippert # LC698799 is no longer available however the MORryde # MR98RR is a better choice for doors with thresholds 30" to 33" off the ground and doorway widths of 23-3/4" to 26-1/4". Depending on your measuerments the MORryde # MR26RR is good for thresholds 25" to 29" off the ground and doorway widths of 23-3/4" to 26-1/4". Either way these steps are large and ensure a safer entry to your trailer with out the disturbing trailer roll that standard steps cause. If you are removing...
    view full answer...

  • Recommended Quad Step MORryde StepAbove with Strut Assist For 30" Door
  • The MORryde StepAbove entry steps install inside your camper's doorframe, measure between the door frame flanges to determine your doorway width. The doorway threshold will be used as the mounting point, measure from the mounting point to the ground for entry height. If the width of your doorway is at its narrowest, 30", and you want a four step model, that would be the MORryde StepAbove, # MR28RR. However, this does not have the Strut-assist feature. The best fit with Strut-assist...
    view full answer...

  • TorkLift Glowstep Revolution Size Selection
  • Since you have the 27" wide entryway, the only additional thing we need to know is the "Entry Height." The attached photo will show you how to measure from the top mounting point to the ground. From there use the attached chart. For instance if your entry height was 38" high, then you would use # TLA8004. Watch this though: If your entry height was 36" then you could use # TLA8004 or # TLA8003. The steps for taller entryways will extend out further. The steps for shorter entryways...
    view full answer...

  • Recommended Permanently Mounted 4 Step Scissor Steps For Camper
  • I may have another option but unfortunately the Brophy Camper Scissor Steps # SS04 you have were not designed to be permanately installed and will not work with the TorkLift GlowStep Stow N' Go Mounting Bracket # TLA7820 you mentioned. The Brophy # SS04 was designed to be removed when traveling, and only installed onto the camper when needed. The only option I can offer that would give you a permanently mounted option on your camper would be to use steps that were designed to be permanently...
    view full answer...

  • Replacement Steps for SCS/Frigette 733-0074 On RV
  • I would be more than happy to help you find replacement steps for the Scs/Frigette 733-0074 steps on your 2008 Monaco Dynasty Renaissance IV! We don't have any exact conversions but we do have replacement 2-step steps that you can potentially use. You'll just want to choose the steps that fit your application best. The 42 Series Kwikee Step # LC372779 is 25-1/4" wide and has a mounting plate that is 30-1/4" wide x 24-11/16" deep. The 47 Series Kwikee Step # LC427247 is 26-1/4"...
    view full answer...

  • Do MORryde StepAbove RV Steps MR26RR Fit 24 Inch Wide Doorway
  • The doorway width - the width from flange to flange of your doorway - needs to be between 23-3/4 inches and 26-1/4 inches, so yes, your 24 inch door will allow you to use the MORryde steps you asked about, which are the following part number: - MORryde StepAbove RV Steps - 2 Steps # MR26RR The only other thing you need to be sure of is the entry height (which is measured from the doorway threshold on your camper to the ground), as the # MR26RR is for entry heights measuring from 25...
    view full answer...

  • How Much Clearance is Needed Between Entry Door and Threshold of RV for MORryde StepAbove
  • The standard clearance requirement for the MORryde StepAbove RV steps like part # MR88RR is 3/8 of an inch which is the same for the # MR28RR.
    view full answer...

  • Manual RV Steps for 24 Inch Wide Door Frame with 6 Inch Rise/Drop Between Steps
  • Thank you for all the information; that allowed me to do quite a bit of research. To answer your questions in regard to the Lippert SolidStep, there isn't a 4-step version of # LC698799, which is a triple step that fits 24 inch wide door frames. Additionally, there isn't an option to add an extra step, nor are they sold separately. Therefore, according to my contact at Lippert, if you were to take on such a project, you'd need to provide your own parts and come up with a plan to execute...
    view full answer...

  • How To Mount TorkLift GlowStep Stow N' Go Steps To Camper With 9" Deep Bumper
  • I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear # TLA7843 away from your camper to clear your bumper. It may be possible to have a local fabrication shop make a custom bracket for your application. Instead I recommend installing the # TLA7843 to the bumper of your camper as shown in the included pictures, this will allow you to still use the step, but will not require a...
    view full answer...

  • Comparing Camper Scissor Steps Brophy AS24 vs. Torklift TLA7804
  • Both the Brophy # AS24 and the TorkLift # TLA7804 are easily removed when not in use- and it's actually recommended that you do so. Additionally, they both weigh in around 26-lbs total, so they're easy to move on and off; so they'd both be great choices for what you're looking for. Overall I prefer the TorkLift # TLA7804 because of the quality of TorkLift products in general, plus you'll have the ability to add the All Terrain Landing Gear for TorkLift GlowStep Scissor Steps for RVs...
    view full answer...

  • Lippert SolidSteps for 2021 Forest River Surveyor Legend 18RBLE
  • To measure for fit of the Lippert SolidStep, measure the entry way from right to left at the narrowest point. Generally there will be a flat metal flange that extends out 1/2" all around. This is the flange that the door closes against and keeps the door from trying to swing inside. From that measurement, round up to the next even inch. So, your door (at the narrowest point) is 21-1/4" wide to the door flange, and rounded up we get 23". The narrowest width for solid steps is 24 inches....
    view full answer...

  • 2 Step Solution For A Forest River Wildwood 171RBXL
  • For your Forest River Wildwood X-Lite 171RBXL you are looking for the SolidStep Manual Fold-Down Steps as your solution. Which part number you need will depend on your doorway width. If you have a door frame width of 26" - 29-7/8, you'll want the 26" - 29-7/8" Wide RV Door Frames part # LC733931 or part # LC713662 for 24" wide door frames. Included is an installed example for reference.
    view full answer...

  • Torklift GlowStep Replacement Support Bracket and Bolt
  • I have a solution for you but we don't have a replacement bracket to replace the support and bolt that was broken on your TorkLift GlowStep similar to the # TLA8004 . Instead you would need to use the Add-A-Step for TorkLift GlowStep Revolution Scissor Steps # TLA8101 which will work on any TorkLift GlowStep models with the 25-7/16" wide mounting base. You can use the parts in this kit to replace your broken parts or replace an entire step. If you have the 27-7/16" mounting base model...
    view full answer...

  • Fitment of Brophy Camper Scissor Steps for Truck Campers
  • The Brophy Camper Scissor Steps for truck campers, # AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points and chart.
    view full answer...

  • Difference Between Kwikee 40 Series RV Steps # LC3726892 and # LC3726891
  • There is a slight difference between the # LC3726892 and # LC3726891. The # LC3726892 comes with a control switch setup that allows the light and step to come on and off with the opening and closing of the door.
    view full answer...

  • How To Measure Doorway Width for Lippert SolidSteps On a Grand Design Solitude
  • In order to choose the correct SolidStep Manual Fold-Down Steps you will need to measure the opening of your doorway inside the trim pieces. I have attached a photo to show this. If the threshold height is over 35" when measuring from the ground while level to the bottom of the doorway then you can indeed use a quad step. For this we have part # LC678025 for 26" doorways, part # LC791574 for 26"-30" doorways, and part # LC791575 for 30" - 36" doorways.
    view full answer...

  • Lippert Fold Down Solid Step for 2017 Coachman RL251
  • You will need two measurements to pick the perfect fitting Lippert fold down solid steps. First the door way width which is the distance between the narrowest part of the door, usually where the flanges stick out. See the picture on the product page. Second you will need to measure the "Entry Height," which is the height from the threshold at the bottom of the door to the ground. With these two number in hand refer to the chart of the product page. I have attached a copy of it here. For...
    view full answer...

  • Do Fold-Out Steps Need to be Removed When Mounting Brophy Scissor Steps
  • That is a good question, and you can leave your current fold-out steps up and in the folded position when installing the mounting bracket of the Brophy Scissor Steps. The reason is, the bracket will be installed just underneath the door so as long as when your steps are folded up there is no interference in that area the Brophy steps will be a great option. I added a photo for you a customer sent in which shows the bracket and steps installed so you can get an idea of how they mount. The...
    view full answer...

  • Solution for Kwikee RV Electric Steps that Work in Reverse After Installed
  • We're familiar with this issue which happens when the incorrect switch is used. Kwikee Steps use two different magnetic switches. One is a normally open circuit and the other is normally closed circuit. The switch must match the controller. Otherwise, the steps will work in reverse, as you described. The original switch kit included with the newer Kwikee 32 Series Electric RV Steps # LC372261 is an open circuit. The two magnetic sensor tabs mount in the doorframe and on the door. When...
    view full answer...

  • Handrail for Second Generation MORryde StepAbove
  • For your Second Generation MORryde StepAbove, please take a look at the, # MR83AR. This is designed specifically for the steps you have.
    view full answer...

  • What RV Steps Will be the Best Replacement for My Jay Flight Jayco 25BHS
  • The replacement steps I recommend for your Jayco Jay Flight 25BHS is the MORryde StepAbove RV Steps. I recommend the MORyde steps because the legs that extend individually on each side, providing maximum ground contact and stability. You will need to measure the entry height to your trailer to get the correct fit, since you already know the height we can use that to narrow down the possibilities. If your entry height is 30" - 33" you will need # MR68RR, if the entry height is 34"...
    view full answer...

  • Handrail For Use With Lippert SolidStep Entry Steps
  • We do have handrails that are going to allow for an easier way for your mom to get up the steps and into your 2016 Heartland Cyclone, the issue with changing from the Lippert SolidStep Manual Fold-Down Steps # LC791574 to a TorkLift GlowStep is the mounting brackets because none of the GlowSteps share the same mounting bracket dimensions as the Lippert steps. What I recommend instead is keeping your current steps and instead adding a very good handrail, the Lippert Entry Assist Handrail...
    view full answer...

  • Hand Rail For Lippert SolidStep Manual RV Steps
  • Yes, the Lippert Entry Assist Handrail for SolidStep Manual RV Steps part # LC799640 is the hand that you need for your SolidStep Manual Fold-Down Steps for 26" to 29-7/8" RV Door Frames part # LC791574. This hand rail fits third generation Triple or Quad SolidStep models. The Entry Assist Handrail can be easily removed or left in place when storing if clearance allows inside the trailer.
    view full answer...

  • Could Torklift GlowStep Scissor Step Fit 2018 Lance Truck Camper 825
  • What's the entry height of your Lance? I am sure we have a set of the Torklift Glowsteps that will work but we need to know for sure the entry height to pick out right size. For example, the part # TLA7844 fits the height range of 31-42 inches. And the part # TLA7845 fits the height range of 38-1/2" - 50".
    view full answer...

  • How to Determine the Correct RV Steps for My Doorway
  • If you are measuring at the lip that the screen door rests on, you are likely shorting yourself a little bit. You want to measure from the inside of the door flange to inside of the door flange. I have included a couple pictures that show the measurements you want to take. If you take those and have at least 25", then you can use the SolidStep Manual Fold-Down Steps # LC791574. If you take those measurements and do not have at least 25" then we do not have a set of Lippert SolidStep's...
    view full answer...

  • Troubleshooting Kwikee Power Step of RV that Opens When Driving in Rain
  • The water is creating a short for the door switch of the Kwikee 32 Series Electric RV Steps # LC372261 which is basically telling the module that the door is open when it's not. Either there's exposed wire between the door switch circuit which the water is creating a short or the module is allowing water to seep in and create the short there. The step light switch wiring should be purple and black. You might check to see if there's any exposed wiring you could potentially seal up better....
    view full answer...

  • Is There a Replacement Gearbox and Motor for 1989 Electric Step
  • So while we do have some options for you, there are no longer specific motors and gearboxes for electric steps manufactured before 1999, so for your 1989 Pace Arrow, what you will likely need is a motor upgrade kit, which includes the motor, linkage, control unit, switch kit, and hardware for installation. Keep in mind that this would only be for specific Kwikee steps, with the right one depending on the series of Kwikee step you have. - Kwikee Series 22, 23, 28A, 30, 32, 33, 34,...
    view full answer...

  • Motor Clicking on Tread Lite Electric Double Steps
  • A clicking motor on your Tread Lite Electric Double Steps # LC353543 or # LC353621 is indicative there is an issue with the motor not sensing the proper amperage at the end of the extension cycle, which is what tells it to shut off when it is finished extending. So the best option is going to be to replace the motor with the Replacement Motor for Lippert Tread Lite Powered RV Steps # LC183058. I have added a link below to a video review for you to check out as well if you'd like to...
    view full answer...

  • TorkLift GlowStep Stow N' Go Scissor Steps for 2022 Arctic Fox 990 With Platform
  • The TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear, # TLA7834 is for an entry height of 31" - 42". Find the mounting spot for the bracket on your vehicle and measure from that point. The # TLA7835 part number is for height of 38-1/2" - 50". We also have available the TorkLift GlowGuide Handrail, # TLA7621, note linked product video. And the Pin Lock for TorkLift GlowStep Scissor Steps, # TLA7509. This replaces one of the pins that holds the scissor steps to the mounting...
    view full answer...

  • Steps Needed for 24" Doorway and 32" Entry Height
  • For your 2021 Keystone Passport SL Travel Trailer with an entry height of 32" and door width of 24", yes, the correct SolidStep Manual Fold-Down Steps is option, # LC698799. Currently these are not in stock. However, I do have a couple of viable alternatives to suggest. The MORryde StepAbove RV Steps, # MR98RR is for 23-3/4" to 26-1/4" wide doorways and entry height of 32"-33". There is also the Strut Assist version of this model step in, # MR45RR. Plus an additional option of the Handrail...
    view full answer...

  • Torklift Replacement Steps for Grand Design Reflection 5th Wheel Including 303RLS
  • The Torklift # TLA8003 (3 Steps) will fit for your trailer. These are intended for a mounting bracket measuring 27-1/2" and an entry height of 25-1/2" to 36". Alternatively, the Torklift # TLA8004 (4 Steps) is designed for an entry height of 32-1/2" to 44" and will extend out further. If you have trouble on steps I would recommend the 4-step model, just know that they extend out further, otherwise the 3-step model is fine. Also check out the Torklift # TLA7621 Hand rail. 4 steps...
    view full answer...

  • Replacing Triple Step, SolidStep Manual Fold-Down Steps With Quad Configuration
  • If you currently have the Triple Step, SolidStep Manual Fold-Down Steps for 25" to 28-7/8" RV Door Frames, # LC791572 and prefer a quad step, I suggest part number # LC791574. This is the same SolidStep for 25" to 28-7/8" RV door frames but in a quad configuration and will mount exactly the same your current install.
    view full answer...

  • Can You Add a Step to the TorkLift Glow Step Scissor Steps
  • Yes; there is a way to do this. In order to add a step to your TorkLift Glow Step # TLA7803 you can use the Single Add-On Step for TorkLift GlowStep Kits - 20" Long x 8" Deep # TLA7801. This adds a step in the middle and leaves the rest of the step in tact.
    view full answer...

  • Picking Out Torklift Glow Step That Fits Lance Model 1475
  • The TorkLift GlowStep Revolution Scissor Steps # TLA8004 that you referenced are designed to fit entry heights on RVs that are between 32-1/2 and 44 inches which which might be a little higher than what you have on your 2018 Lance 1475 based on the pictures I was able to find online of it, we don't have a way to get the exact threshold height of your RV so you'll have to take a quick measurement to verify. If you find you have lower height we have the part # TLA8102 which has two steps...
    view full answer...

  • Availability of Replacement Motor for Kwikee Series 23 Steps on 1999 Teton Fifth Wheel
  • The motor for the 1999 and older style Kwikee Series 23 steps is no longer available, but they do have a replacement upgrade motor that will work. For your older style of Kwikee Series 23 RV steps the Lippert Components Kwikee Step Motor Conversion/Upgrade Kit # LC379145 is the correct kit to use. This will upgrade what you have to the current style of motor and module. This motor upgrade kit for is a very popular upgrade kit which works with most Kwikee Steps. It offers an improved...
    view full answer...

  • MORryde StepAbove For RV Entry Door 30 Inches From The Ground.
  • I can help you out. Since these both fall in to your range at 29-30 inches. You need to ask yourself how wide is my door and how many steps do I want? As long as your doorway is(from inside flange to inside flange): 23-3/4" - 26-1/4" wide, either of these will fit. I personally would pick the 3 step version because it will give you more space if you park somewhere with a larger drop down or uneven surface and its drop rise is 8 inches, the two step version has a drop rise of 9...
    view full answer...

  • Can Torklift Revolution Uprising TLA9005 Fit 2019 Forest River Flagstaff Classic Super Lite 8321KBS
  • In order for the bracket of the TorkLift GlowStep Revolution Uprising Steps # TLA9005 that you referenced to fit the door sill the height does need to be between 5/8 inch and 3/4 inch to allow the door to still close over it. So if you can use a spacer like you mentioned to raise your height to fit that range then this will fit well in this regard as well as as the threshold height dimension you mentioned. Since you are so close I would imagine it wouldn't take much if anything to get...
    view full answer...

  • Recommended Replacement Steps For 2017 Forest River Sandstorm 27
  • I can absolutely recommend a set of replacement steps for your 2017 Forest River Sandstorm 27 but you will need to do a quick measurement of your entry height to confirm the correct model as we unfortunately do not have a way of checking the entry height on your RV. I recommend the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear which you will need # TLA8104 if your entry height is between 32-1/2" - 44", # TLA8103 if your entry height is between 25-1/2" - 36", or # TLA8102...
    view full answer...

  • Which SolidStep Fold Down Step for Doorway that is 25-1/2 inches Wide
  • Since your step is 25-1/2 inches wide the correct triple SolidStep is the part # LC791572 according to our contacts at Lippert.
    view full answer...

  • Door Will Not Close After Installing The Solid Step On a 1995 Prowler Camper
  • I have found with a lot of the older campers like your 1995 Prowler that the screen doors are installed lower so it creates an issue when closing. Unfortunately there aren't a set of steps like the SolidStep Manual Fold-Down Steps that doesn't create this issue on older campers. I actually had the same issue with an older camper that I installed the steps on here. If your door is close to closing, a couple suggestions that you can try first is to not reinstall the decorative roll plate...
    view full answer...

  • replacement stairs for Eagle Cap 1165 Truck Camper
  • You will need two measurements to determine the best fit for your camper. First is the "Entry Height". This is the measurement from the top of the mounting bracket to the ground. See the example picture on the product page. The TorkLift # TLA8006 that you referenced is suitable for entry heights between 46-1/2" to 60". The second measurement is the "Mounting Bracket Width". With the old steps removed, there will be a black metal mounting bracket that held the old steps. If yours measures...
    view full answer...

  • Replacement Power Step for 2006 Newmar Dutch Star
  • Based on what you described having on your 2006 Newmar Dutch Star the part number # LC3722617 does seem like it would be what you'd need but you should note that this isn't a complete step kit as it is missing the control unit. So instead you'd want the part # LC372261.
    view full answer...

  • Troubleshooting Kwikee Electric RV Steps That Only Retract 3/4 Of The Way
  • It sounds like something might be bent or damaged either on the steps, gearbox, or motor of your Kwikee Electric RV Step Complete Assembly 32 Series # LC372261. First remove the gearbox and motor and manually move the steps to see if they are the cause. If not then check the gear on the outside of the motor housing for any teeth that are damaged. If there is no damage then the culprit is most likely the internal gears in the gearbox. you can replace the gearbox with the Replacement Gear...
    view full answer...

  • MORryde StepAbove Fold Down Step for Forest River Salem 178bhskx
  • Since your threshold is 28-1/2 inches tall from the ground and your doorway width is 24 inches the correct MORryde StepAbove is the part # MR26RR. The three step options like the # MR98RR would be too tall and wouldn't fold down all the way so they wouldn't work.
    view full answer...

  • Comparing The Brophy # AS24 And Torklift # TLA7844 For Truck Bed Camper With Limited Mounting Space
  • Not following the manufacturer's instructions to the letter will give them an excuse if something were to happen so while I can't recommend drilling the extra holes to ensure it's safely mounted, it's the only way that the steps will work with your application. I called Brophy and the warranty for their steps is a 1-year warranty. As for connecting the landing gears of the TorkLift GlowStep # TLA7844 to the Brophy Camper Scissor Steps # AS24, this is something that we would not...
    view full answer...

  • Retractable Single Step Kit that Can Fit 2019 Ford E-450
  • The easiest way to get the step and switch kit you are wanting is with the part # LC3747453 would work on your 2019 Ford E-450 to provide it with a single step that is retractable.
    view full answer...

  • Additional Handrail for Stromberg Carlson Econo Porch Trailer Steps
  • Yes, we do offer this! Please select the Replacement or Additional Handrail for Stromberg Carlson Econo Porch Trailer Steps, # SP5110-HR. This provides an additional handrail for your Stromberg Carlson Econo Porch trailer steps # EHS-102-R.
    view full answer...

  • Differences Between Torklift GlowSteps part # TLA7804-8000 and # TLA7834
  • The big difference is that the part # TLA7804-8000 does not come with a bracket for how it attaches to the truck whereas the part # TLA7834 does. The bracket is for a more permanent install where they'd fold up and store on the vehicle whereas version without the bracket is a set you'd remove and install every time you use it.
    view full answer...

  • How Do You Mount The TorkLift GlowStep Stow N' Go Scissor Steps
  • Nice question, lets find out below: First we need to make sure that you have the right fit. Measure from the ground up to the door frame and then measure the width. **TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 3 Steps - 375 lbs - Black Bracket # TLA7833. This unit listed above fits entry heights 23-1/2 to 34-1/4 inches tall. The mounting bracket needs an area right under the entry door that is 21-1/2" wide x 12-1/2" tall x 8-1/2. Here is a list of the basic...
    view full answer...

  • How to Install MORyde StepAbove RV Steps with a Door that has a Gas Strut Obstructing Clearance
  • If you are wanting to install the MORryde StepAbove RV Steps # MR98RR you would need to remove the shock rod/gas strut because it will interfere with the step clearance. You can use the Replacement Controlled Motion Hinge for RV Entry Door # LC95VR (black) or # LC22NJ (white) on your RV door which uses Controlled Motion Technology to hold the door open in any position instead of allowing the door to swing freely. This will work with Lippert RV doors as an alternative to a shock rod/gas strut.
    view full answer...

  • Are The etrailer.com And MORryde Part Numbers The same For Each Unit Or Different
  • Good question, lets check it out: **MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps # MR48RR. The part you are looking at is indeed the same thing, STP-207 is the MORryde part number and # MR48RR is the etrailer part number for the same item.
    view full answer...

  • Troubleshooting Kwikee Electric RV Steps
  • I recommend using the 4-Way Tester Plug for Kwikee Electric RV Steps - Packard Connector # LC379416. This 4-way tester plugs into the linkage assembly of your Kwikee Electric RV Step Complete Assembly - Double - 32 Series - 24" Wide # LC372261 so you can test all of the step components to make sure they're connected correctly. If there is not an issue with a bad connection you will probably need a Replacement Control Unit for Kwikee Electric RV Steps # LC379146. The motor may run...
    view full answer...

  • MORryde StepAbove RV Step that Fits Cross Roads Sunset Trail
  • Thank you for the pictures of the doorway width and height of your Cross Roads Sunset Trail. Based on the doorway width and the threshold height the correct MORryde Stepabove that you'd want is the part # MR98RR. This fits doorway widths of 23-3/4 inch to 26-1/4 inch and heights between 30-33-1/2 inch.
    view full answer...

  • Recommended Fold-Down Steps For A 2013 Cruiser RV Fun Finder X Travel Trailer
  • Yes, we do have just what you need with the MORryde StepAbove RV Steps for 23-3/4" to 26-1/4" Wide Doorways - 3 Steps # MR98RR. You will need to slightly adjust the brackets (pictured below) by unscrewing the bolts and sliding them inward to meet your 22-3/4" flange to flange measurement and then retightening the bolts. As for the handrail, you'll want the Handrail for Second Generation 3-Step MORryde Steps # MR83AR. I've attached some videos below that will walk you through installation...
    view full answer...

  • Need Fold-In Style Steps for Trailer With Narrow Storage Space to Deploy
  • Yes the TorkLift GlowStep Revolution Uprising Steps, # TLA9004 has a booster/bonus step intended for use when needed. This is a three steep model intended for an entry height of 27-3/8" to 34-7/8" with 28" doorways. If you will need the 4th step regularly because of threshold height, it is suggest that you select the four step model, # TLA9005. This too will have that additional booster/bonus step as well as landing gear that creates a stable connection from the bottom step to the ground.
    view full answer...

  • Recommended TorkLift Steps for Palomino SS1240 Pop Up Camper
  • I have a solution for you, but the TorkLift # TLA7843 require much more mounting space than you've got available on your 2020 Palomino SS1240. Because of the limited mounting space under your door, you'll need to use something similar to the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 4 Steps - 20" Wide # TLA7804-8000, which has a very narrow mounting bracket that is 1" tall x 20" long and will work well in the limited space you've got on your Palomino SS1240 camper. I...
    view full answer...

  • Will Torklift RV GlowSteps TLA7834 Fit 2017 Forest River Flagstaff Classic 832BHDS
  • To determine if you are able to replace your 3-step unit with a 4-step unit like # TLA7834, you will need to take a few measurements as RV steps are not custom to the year, make and model of a specific RV. Measure from the ground to the top of the threshold on your RV to determine how much ground clearance you have. The Torklift Steps require ground clearance between 31 and 42 inches. The mounting bracket base dimensions for the Torklift GlowSteps are 21-1/2" wide x 14-1/2" tall x...
    view full answer...

  • How To Determine Which GlowStep Revolution Steps Will Fit A 2017 Forest River Rockwood Mini Lite TT
  • Correct, the TorkLift GlowStep Revolution Uprising Steps w/ Booster Step # TL32SR is the right size for your 25-1/2" wide doorway. However, you'll also need to verify your entry height as well. You'll want to measure from the mounting point to the ground, and use the chart I've attached to verify the correct steps for your 2017 Forest River Rockwood Mini Lite.
    view full answer...

  • Replacement Motor for Kwikee Electric RV Steps Needed
  • The 12V Replacement Motor for Kwikee Electric RV Steps, # LC379147 is the correct replacement motor for Kwikee 32 Series Steps. For 34 Series Steps, Replacement Motor with Mounting Plate, # LC379608 for 2000-2005. And for 2006-Dec 2018, # LC379147 or 2019-Present, # LC62FR. My recommendation is to remove your current motor and look part number/visually compare to images on our product pages.
    view full answer...

  • Troubleshooting Kwikee 42 Series Step that Motor Continues to Run for 2-3 Seconds After Steps Extend
  • It could be that your Kwikee Series 42 Steps # LC372779 are just hanging up and bit and could use some lubricating spray on the gears; you'll want to use a dry silicone spray on these parts similar to the Roadmaster Lube Master # RM-747 to keep everything in working order. With that being said, this is also a sign that the motor on your Kwikee Series 42 steps could be weakening, so you'll want to keep an eye on this going forward. If it ends up that the motor goes out on your steps...
    view full answer...

  • Is There A SolidStep Manual Fold Down Step That Will Fit My 25-1/4 Wide Doorway
  • The SolidStep Manual Fold-Down Steps for 25" - 28-7/8" Wide RV Door Frames - Double - Aluminum, part # LC733931, will fit your RV door without any issues. These steps will fit doorways from 25" wide up to 28-7/8". The 1/4" difference will not cause problems with the fit. I have attached a video review link below.
    view full answer...

  • MORryde StepAbove Steps For A 2007 Keystone Montana 2955RL
  • If I'm understanding you correctly, the MORryde StepAbove RV Steps # MR68RR is 8.3" deep when in the upright position. Based off of the measurements you took of your 2007 Keystone Montana 2955RL, the MORryde StepAbove RV Steps # MR68RR should work great for you.
    view full answer...

  • Troubleshooting the Kwikee Revolution Series RV steps on a 2014 Itasca
  • From what you describe I suggest you examine the motor and gears as it appears they are worn. The Replacement Motor for Kwikee Revolution Series Electric RV Steps, # LC380073 is the correct part number. Or, for a complete replacement of Kwikee Revolution Series RV steps, I recommend the Kwikee RV Electric Steps - Revolution Series, # LC3725791.
    view full answer...

  • Selecting The Correct Handrail For MORryde 4-Step RV Steps, Gen 1 VS Gen 2
  • The MORryde StepAbove RV Steps # MR28RR are a second generation step. This will require the Handrail for Second Generation 4-Step MORryde Steps # MR73AR. To determine which generation step you have you can measure the threaded holes for the steps. On the Handrail for First Generation 4-Step MORryde Steps # MR33RR both sets of holes are spaced 5" on center. The second generation steps the lower set of holes are only 4-1/2" apart while the top set of holes are 6" apart.
    view full answer...

  • Can I Replace Current MORryde 3-step With a MORryde 4-step on 2018 Forest River Flagstaff 832OKBS
  • It is possible that you will be able to switch out your current MORryde 3-step RV steps to a MORryde 4-step, like the MORryde StepAbove RV Steps for 27-3/4" to 30-1/4" Wide Doorways - 4 Steps # MR28RR, but it will depend on a couple of measurements on your 2018 Forest River Flagstaff 832OKBS. Once you determine if you are able to go with the 4-step, it will not be hard to switch out the two steps. I have attached the installation instructions and the Qualification Guide for you to view. The...
    view full answer...

  • Determining Correct TorkLift GlowStep Revolution Scissor Steps For 2012 Rockwood 9312SS
  • I would be happy to help you figure out the correct TorkLift GlowStep Revolution Scissor Steps for your 2012 Rockwood 8312SS, but unfortunately I do not have a list that has the correct step for your trailer. To determine the correct steps you will need to take a few measurements, with the first being the dimensions of the mounting space for the steps under the door of your trailer. There are two different widths offered which are 25-1/2" wide like the # TLA8104, or 27-1/2" wide like...
    view full answer...

  • Will the Brophy Camper Scissor Steps # AS23 Fit My Vehicle?
  • I have a solution for you. Unfortunately, the Brophy Camper Scissor Steps - 3 Steps # AS23 will not work with the dimensions that you provided (thank you!) because you have an entry height of 36 inches from the ground to the entry way. The Brophy steps are only designed to fit steps that have entryway heights of 24-30 inches. With the information that you provided, the best solution would be the Brophy Camper Scissor Steps - 4 Steps # AS04. With these steps, they fit entryway heights...
    view full answer...

  • Wiring Diagram For Kwikee 47 Series RV Steps
  • I tried looking up your invoice using the email you provided but was unable to find an invoice with any RV steps, that being said if you have the Kwikee 47 Series steps # LC427247 that you were looking at then I have attached the wiring diagram for you below. 16AWG Brown: Ground 16AWG Yellow: Ignition Switch 12AWG Red: Battery Positive 16 AWG White: Power Switch If you don't know series you have then you can look for a tag near the motor that will have a serial number...
    view full answer...

  • Adding Electric Step To Converted Ambulance
  • I have a solution for you. Kwikee Electric RV Step Complete Assembly - Single - 28 Series - 23-5/8" Wide # LC3747453. This step has a 7 inch drop so it will cut your 14 inch step in half. Hardware is not included. Extended height: 9-5/8" Folded height: 6" Overall width: 24-3/4" Mounting plate dimensions: 24-1/4" wide x 8-5/8" deep Bolt pattern: 22" wide x 6-1/2" deep Step dimensions: 23-5/8" wide x 10-1/2" deep Drop/Rise: 7-1/2" Motor: 12V Switch kit: 250V Control unit...
    view full answer...

  • Is Item # TLA8003 Compatible With Bracket Dimensions Of 27-1/2 x 13-3/4 And Entry Height Of 29-1/2
  • Yes, TorkLift GlowStep Revolution Scissor Steps Item # TLA8003 is the correct steps for the measurements you provided to replace the steps on your 2016 Keystone Cougar Fifth Wheel. I do recommend, if you have pets, to add the SafeStep Vinyl Barrier Item # TLA7602. K9s have a hard time not looking through the steps as they walk up into the camper and get scared they are going to fall through. Adding the barrier provides a wall so they can see there is a back to it.
    view full answer...

  • Kwikee Magnet Switch for RV Step with 909506000 Module
  • The replacement door magnet switch kit for the auto retract/extend is the part # LC369299 as what you have requires a switch that is "normally open". This is an inexpensive solution that should fix your issue so I would start with it and see if it helps.
    view full answer...

  • What Steps with Non-Bolted Handrails do you Recommend for our Trailer?
  • While we do not have a 3-step solution with a removable handrail like the one you have pictured, we do have a 4-step solution that could work on your clinics. That is the Victory Step Manual Fold-Down Steps for RV and Toy Hauler Patios # LC726895. The handrails that come with this model are easily fastened and removed with turning knobs that do not require any tools. I went ahead and attached a page from the instructions that shows the easy of inserting the knobs. As far as compatibility,...
    view full answer...

  • Replacement Step for a 1996 Monaco Windsor
  • The # LC3747452 is the replacement step, motor, and control for the 28 series Kwikee RV Electric Steps. If you have a 28 series unit then yes this is what is needed. Please look for markings on currently installed steps to identify series or compare measurements. The mounting plate is 24-1/4" wide x 8-5/8" with a bolt pattern of 22" x 6-1/2".
    view full answer...

  • Recommended RV Entry Step That Can Have Steps Added As Needed
  • I may have a solution for you, but the only step that I'm aware of that can have steps actually added to it is the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear - 4 Steps - 25-1/2" Base - 375 lbs # TLA8104; you would want to use the Add-A-Step for TorkLift GlowStep Revolution Scissor Steps with 25-7/16" Wide Mounting Base # TLA8101 to add a step to those. The Lippert Alumi-Tread # LC432698 cannot have a step added to them, unfortunately. I do think these are a nice replacement...
    view full answer...

  • Can the Kwikee 26 Series Electric RV 1-Step Be Obtained Without the Motor
  • The Kwikee 26 Series Electric RV 1-Step is offered with the motor, control unit, and switch as part # LC3711363; the motor and control unit as part # LC371136, and motor and switch as part # LC3711361 but these are the only configurations available.
    view full answer...

  • Mounting Bracket Dimensions of Manual Pull-Out Step
  • The Manual Pull-Out Step for RVs - Double # LC432682 has mounting holes that are about 24" x 7" and although there are not any with a 14" x 7" pattern, you can still use this step. In order to do so you have a couple of choices. The first would be to weld the steps onto your RV while the other option would be to use Lippert Outriggers for Manual and Electric RV Steps # LC301704. You would need Mounting Hardware # LC118155-72 to attach the steps to the Outriggers.
    view full answer...

  • Correct SolidStep Manual Fold-Down Steps for a Doorway Measuring 28.5" from Flange to Flange
  • When measuring your doorway to select the correct steps you will need to measure from flange to flange, not the entire doorway. Since you get a measurement of 28-1/2" flange to flange, the correct steps will be the SolidStep Manual Fold-Down Steps # LC791572 which fit doorway widths of 25" - 28-7/8" and height of 27" - 36". Not the # LC791573 which would be too wide for your doorway.
    view full answer...

  • Recommended Brophy Camper Scissor Steps For 40" Entry Height
  • The 4 step Brophy Camper Scissor Steps, # AS24 is recommended for an entry height of 31" - 40" while the 5 step model, # AS25 crosses over for an entry height of 40" - 48". My recommendation is to go with the 5 step model that provides greater range.
    view full answer...

  • How Much Does The MORryde Qucik Connect RV Steps MR73RR Weigh
  • I spoke with MORryde and they informed me that the MORryde Quick Connect RV Steps # MR73RR weigh 22 pounds.
    view full answer...

  • RV Steps for 29.5 inch door w/ a 36.5 Drop
  • For a 29.5" doorway with a 36.5" stair height I recommend the MORryde StepAbove RV Steps for 27-3/4" to 30-1/4" Wide Doorways - 4 Steps item # MR28RR. These steps are for entryways with a doorway width (from inside flange to inside flange) of 27-3/4" - 30-1/4". The step dimensions are 23-1/2" wide x 8" deep and the top step depth is 10-5/8".
    view full answer...

  • Dimensions of Strut Cover Box on MORryde StepAbove RV Steps
  • The box that covers the struts on the MORryde StepAbove RV Steps # MR75RR measures 4" wide x 6" deep x 14.25" tall which you can see in the attached diagram. Attached is a review video for you to check out.
    view full answer...

  • Installation Questions About Power Source for Kwikee Electric RV Step on Ambulance
  • I have a solution for you, but since you don't already have a step installed you'll need to use the Kwikee Electric RV Step Complete Assembly - Single - 28 Series - 23-5/8" Wide # LC3747453 instead of the # LC3747452 since it has all of the components needed for a new installation, where the # LC3747452 is designed to work as a replacement with existing components. With that said, you can use the Kwikee Electric RV Step Complete Assembly - Single - 28 Series - 23-5/8" Wide # LC3747453...
    view full answer...

  • Is There a Folding Double Step That is 24-1/4 Wide x 8-1/4 Deep
  • There is a folding double step that has the same 24-1/4 inch wide x 8-1/4 inch dimensions as the Lippert Manual Pull-Out Step for RVs - Single # LC432678; the step you are looking for is the following: - Lippert Manual Pull-Out Step for RVs - Double # LC432682 I have added a link below to a video review for you to check out as well if you'd like to take a look.
    view full answer...

  • Torklift Glowsteps For Truck Campers Plus Add-On Step
  • If your door entry height (the distance from the ground to the threshold) is 37" and you bracket area (width) is 21-1/2" or greater then the TorkLift # TLA7804 is the correct fit. You can use the # TLA7801 Single Add-On Step to extend your reach.
    view full answer...

  • Mounting TorkLift GlowStep Camper Scissor Steps to 2022 Adventurer 80RB
  • The TorkLift GlowStep Camper Scissor Steps, # TLA7805-8000 has a mounting bracket that attaches to the camper and held in place with included lag screws.
    view full answer...

  • Quick Release Hinge For Lippert Manual Fold Down Steps
  • I spoke with Lippert and they confirmed that SolidStep Manual Fold-Down Steps for 29" to 36" Wide RV Door Frames # LC791575 does not have a quick hinge function, just manual fold down and raise up. We do offer the Torklift GlowStep Revolution # TLA9005 that is a scissor style design made to fit and be used in small or tight paces. This product also extends to reveal a 5th step for use and fits doorways 28" wide. We do carry the detachable quick hinge kit for Morryde first generation...
    view full answer...

  • Replacement for Kwikee Revolution Step 9010000464 on 2011 Winnebago Journey 40U
  • According to Lippert, the correct replacement for your 9010000464 model Kwikee Revolution Steps is the Replacement Steps, Motor, and Control for Kwikee RV Electric Steps - Revolution Series # LC3725791. If you want the complete assembly with the override switch you will also need the # LC369311.
    view full answer...

  • What MORryde Steps Will Fit On My 2016 Grand Design Reflection 5th Wheel.
  • To get the four steps you need the MORryde StepAbove Strut Assist Fold-Down Step for 27-3/4" - 28-1/4" RV Door Frame - Quad # MR85RR is the way to go. The legs are adjustable and they have foot pads that move independently to give you stability on uneven surfaces.
    view full answer...

  • Torklift GlowStep Revolution Uprising Steps Installation Guide
  • The TorkLift GlowStep Revolution Uprising Steps w/ Booster Step - 2 Steps - 24" Base - 325 lbs Item # TLA9103 simply bolts to the frame of your entryway. I've attached a video that offers more info on this exact product and a video that shows how to install an entryway stair kit.
    view full answer...

  • Solution for Needing Replacement Frame for Kwikee Series 35 RV Steps
  • You are correct that the part # LC3691461 is the complete kit Lippert Kwikee 35 Series of steps. We don't have just the frame alone for this model but we do have the part # LC369146 which is the frame, motor, and module and does save some money.
    view full answer...

  • SolidStep Manual Fold-Down Steps Leg Adjustment Height
  • The SolidStep Manual Fold-Down Steps for 25" to 28-7/8" RV Door Frames - Triple - Aluminum, # LC791572, has adjustable legs that adjust in 1" increments. When drawn fully in the feet can be pulled in approximately 1" from the bottom step. Please note the product review and installation videos that have been linked. A valuable addition to the SolidStep is the, Lippert Entry Assist Handrail for SolidStep, # LC799640. And the SolidStep Locking RV Storage Box - Powder Coated Steel -...
    view full answer...

  • How to Determine if MORryde StepAbove RV Steps MR28RR Require Modification
  • MORryde has qualifications which will tell you if any modifications need to be done to install the MORryde StepAbove RV Steps for 27-3/4" to 30-1/4" Wide Doorways - 4 Steps # MR28RR. As you can see by the cut out I added below, the threshold rise needs to be between 5/8" and 3/4", and the gap from the bottom of your entry and screen door to the top of the threshold needs a 3/8" gap. So if you have those measurements you don't need to do any modifications; otherwise they would be necessary...
    view full answer...

  • Recommended Lippert SolidStep For A 2017 Grand Design Solitude 5th Wheel With A 29" Door Frame Width
  • You can always use a smaller width step if you have to, so the # LC791574 would still work. A lot of times people have things in the way like a cabinet door or fire extinguisher that prevents them from folding the steps back up into the RV so they end up having to use a smaller width step. If you want the maximum width step for a 29" doorway then you can use the following steps: If you have a 22" - 28" entry height you'll want the Lippert SolidStep # LC733932. If you have a 27"...
    view full answer...

  • Determining The Correct MORryde StepAbove RV Steps For A Travel Trailer
  • I spoke with MORryde and they stated the item number you were given does not match anything they have. Possibly it's the item number that the RV shop uses instead of the manufacturer number? Based on your photos it appears to me that you have a 29.5" door width and 33.5" entry height you'll need the MORryde StepAbove RV Steps # MR68RR. These steps are compatible with a door width of 27-3/4" to 30-1/4" and an entry height of 30" to 33-1/2", so you'll fall within these requirements. Looking...
    view full answer...

  • Bolt Pattern and Mounting Plate Dimensions for Kwikee 40 Series Steps
  • In regards to the Kwikee 40 Series Electric RV Steps like part # LC3726891, the step mounting plate is 25-3/4" wide x 14-3/4" deep and the bolt pattern is 20.5" wide x 12-7/8" deep. I confirmed this with Lippert for you and have attached a photo below.
    view full answer...