Expert Answers about Chevrolet Silverado RV and Camper Steps
- Correct Replacement for Kwikee Steps 903206000
- I really appreciate all the information as well as the photos.
After doing some research, I found that the exact replacement for your Kwikee steps with model number 903206000 are indeed the Kwikee 32 Series Electric RV Double Steps # LC372261. I also was able to confirm this with my contact at Lippert.
So, why then are your steps measuring taller than the specs listed for the # LC372261? Well, after 17 years of use, it's only understandable that the weight being repeatedly applied...
view full answer... - Smallest Size Doorway Opening for SolidStep Manual Fold-Down Steps LC791572
- The SolidStep Manual Fold-Down Steps part # LC791572 will fit a door way from 25" -28.9" wide when measuring the frame inside. If the factory label sticker shows a doorway width between 26"-29" then the above steps will work for you just be sure to verify the threshold is between 27"-36".
I have attached a photo below to assist.
view full answer... - How to Pick Out Correct Height Torklift GlowStep for Rear of Truck Bed Camper
- Can you tell me the distance from the ground to where the door threshold is? Thats the dimension needed to pick out GlowSteps like the # TLA7804 which is a 4-step set with a mounting bracket height of 34-1/2 inches.
If the threshold dimension you took was near 34-1/2 inches this would be a great fitting option.
view full answer... - Alternative to Replacing OEM RV Steps with 2-Step Pull Out Step
- The 2018 Dutchmen Coleman Lantern LT 16FB travel trailer appears to have a single-step OEM entry step. If you want to convert this to a 2-step you want to note the overall size of the step unit, the mounting hole spacing and also the retracted height. You do not want to risk reducing your ground clearance with a new 2-step unit.
Most 2-step pull-out steps for towable travel trailers are 24-inches wide like # SMFP-2100, which is the item you referenced, and like the other similar steps...
view full answer... - Which LCI SolidStep Fits 2019 Winnebago Micro Mini 2306 BHS
- You are correct, for your 2019 Winnebago Micro Mini 2306 BHS the correct Lippert SolidStep is the # LC713662 based on the dimensions you listed.
view full answer... - How to Correctly Measure for Trailer Steps
- In order to find the correct fit, you are going to have to do a little measuring. You will want to start by measuring the width of your current step assembly, followed by the height from step to step. After that, you will want to measure from the center of the step assembly at the crossbar to the diagonal line at edge of the bottom stair.
For example, the Lippert Manual Pull-Out Step, # LC432687, has three steps and measures seven inches at the bottom two steps, has a stair assembly...
view full answer... - Recommended Replacement RV Steps For 2013 Montana Fifth Wheel Trailer
- You are correct. the RV steps we offer are 24-inches wide regardless of the amount of steps.
I recommend installing replacement steps like part # SMFP-4400. These are 24 inch wide steps. The mounting base dimensions are 27 inches wide x 9-inches deep. You would need to build up the mounting location on your RV to work with these steps.
view full answer... - Availability of Pull Out RV Steps That Are 25-1/4 Inches Wide
- Lippert components offers a 2 step unit with a 25-1/4 inch overall width, with the bolt hole spacing being 24 inches on center, side to side and 7 inches front to back on center. The part number is # LC432682.
view full answer... - Dimensions and Brackets For The Triple Rise Manual RV Steps
- The Stromberg Carlson Flexco Manual Pull-Out Steps for RVs - Triple - 9" Drop/Rise - 24" Wide - 350 lbs, # SMFP-3200L, is a great product. The folded up measurements are 16-3/16 inch tall x 12 inches wide x 25-3/8 inches long. I've attached a picture to give clarity. I've also attached a review video for you.
The mounting points are included in the design with 6 bolt holes. Pre-drilled holes on the top mounting base match up to factory holes on the bottom of many RV's. The hardware...
view full answer... - Can TorkLift GlowStep Revolution Scissor Steps Be Used If Not Fully Extended
- Yes, you can absolutely still use and walk on the TofkLift GlowStep Revolution Scissor Steps # TLA8004 even if they aren't fully extended. I did reach out to my contact at TorkLift to verify this.
They will have no problem supporting weight when in this state and this very design is what makes them a great choice since they can be used in tighter spaces or areas with unlevel surfaces.
view full answer... - Brophy Aluminum Camper Scissor Bracket Width
- The mounting bracket of the # AS04 is 25 inches wide.
The step width is 18 inches.
view full answer... - Could Manual Pull-Out Steps # LC432690 Fit 2010 Grey Wolf Super Lite
- The Manual Pull-Out Steps # LC432690 are designed to fit the standard mounting brackets found on RVs like your 2010 Grey Wolf Super Lite by Cherokee. That said, there are sometimes variances in the widths of the brackets typically based on the number of steps on the assembly. This setup is designed to fit mounting bracket dimensions that are 27-1/2 inches wide outside to outside. Most likely that's what you have but worst case scenario you could weld these directly to your frame, have the...
view full answer... - Stairs for Getting in and out of a Truck Bed Camper in a 2005 Chevy Silverado 1500
- On the Brophy scissor steps # SS03, they measure just 5-1/2 inches from the mounting surface to the nearest vertical support for the first step so it would not work for you. But you might like hitch step # HE4045 if your truck has a 2 inch trailer hitch receiver. You would use the tailgate as one step then this step as the second step down.
Another option is the Truck-Pal, # 10-3000. This ladder installs on the tailgate and folds out when needed. I have linked some videos for you to...
view full answer... - How Does Motor of Coach Two Step Replace
- I will be happy to help explain how to remove the old motor and install the new one # LC301695.
The motor and gear assembly can be replaced by first disconnecting the two pin connector from the module to the motor.
Next, remove the p-clamp holding the wire harness to the motor mount.
Then, remove the ball joint linkage from the gear followed by the self-tapping screw that holds the ground wire.
Next, remove the 3 bolts that hold the motor mount to the step base. Care should...
view full answer... - Would the Flexco Manual Pull-Out Steps # SMFP-3200L Replace 5th Wheel Steps
- If you can determine if the steps you have are Lippert or Stromberg Carlson then yes, the Flexco Manual Pull-Out Steps # SMFP-3200L that you referenced would work great as an easy replacement for what you currently have. Otherwise I am confident you could get these steps to fit, but it might take a little fabrication. Most RVs use the same style of brackets for pull out steps, I wouldn't say that all of the steps fit easily on every RV but for the most part you can make just about any step...
view full answer...
Go To Results