bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Toyota Trailer Spindles


  • Replacement Spindles For 3,500LB Trailer Axle With Tapered Spindle with 1-1/16" & 1-3/8" Bearing ID
  • We do have the following replacement spindles that will fit on your axle. #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter # TRU24FR #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter # TRU84FR #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter # TRU64FR #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axle - 1-3/4" Diameter # TRU74FR
    view full answer...

  • Replacing Trailer Axle Spindle From Older Short Spindle To BTR E-Z Lube Spindle
  • It sounds like you have an older style trailer axle with the short spindles. You will need a new Spindle # TRU44FR to mount on your axle as the short hubs are now obsolete. This will allow you to use the what is now standard length spindle dimensions. The CE Smith Trailer Idler Hub Assembly w/ Case # CE13315 is designed to fit the newer BTR spindles that are more commonly found on trailers.
    view full answer...

  • Replacing Obsolete Trailer Spindles With a 1-3/8" Straight Spindle With Current Size Spindles
  • I am going to recommend changing out your spindles for one of the current size spindles as your spindle is obsolete and no one is producing parts for it currently. This will be extremely helpful in the event of a breakdown as these parts are readily available. We have a few options based on your current axle capacity. I have included a 3,500lb and 5,200lb selection below and included both idler hubs and drum brake hubs. 3,500LB Axle Parts #84 E-Z Lube Spindle w/ Brake Flange # TRU74FR Easy...
    view full answer...

  • Replacement Spindle for 1996 Yacht Club Trailer
  • We do offer replacement spindles for trailer axles that can be seen using the link provided. You will want to match the axle capacity (look for a sticker or plate on the axle itself) and its shape and dimensions, including length and diameter. Trailer spindles must be installed by a qualified professional welder. Spindles must be welded on perfectly concentric or you will have tracking problems. A trailer shop will have the right jigs to allow the spindle to be welded on correctly. I...
    view full answer...

  • Replacement Spindles for Featherlite Horse Trailer
  • We do offer replacement trailer spindles, and all are shown on the linked page. These include agricultural, EZ Lube and standard types. Your trailer VIN will not tell us which spindles you need but you can select the right one based on your axle's weight rating and measurements of the current spindle. You'll need a digital caliper like to measure precisely. Note that new spindles should be welded on only by a professional welder who has experience and the correct jigs for installing spindles...
    view full answer...

  • Replacement Spindle Nut Kit for 1999 Floe Pro Plus Snowmobile Trailer
  • I checked the Floe Trailer website for any available specs on their trailer's spindles but their site does not provide this information. They do list axle parts for their 2004-and-later models but not the spindle specs. Redline Spindle Nut Kit for Dexter Standard and EZ Lube Axles, part # RG05-100, has a 1-inch inner diameter and fits a 14-TPI (threads-per-inch) spindle. I have linked our main page for trailer spindle parts. You may be able to find a sticker on your axle that tells you...
    view full answer...

  • Replacement Spindle Washers For An Old Trailer With 10k Axles
  • We carry a variety of different spindle washers so you'll want to measure your current washers and note the design to match it up to the correct design for your spindles: Replacement Spindle Washer - Tang Type for E-Z Lube # 5-101 Washer For 1" Spindle # SW1000 (most common) Tang Replacement Spindle Washer # 5-71 D Washer for EZ Lube Spindles # 5-23 Washer Spindle Tongue # 165863
    view full answer...

  • Availability Of Replacement Spindle For 7000lb Dexter Trailer Axle Beam W/ 4" Drop 8327872
  • I have another option for you but there is not a screw on spindle available for the # 8327872 you were looking at. To replace one of the spindles on the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles - 94" Long - 7,000 lbs # 8327872 you would need to have the #42 E-Z Lube 4" Drop Spindle w/ Flange for 5.2K to 7K Trailer Axles - 3" Diameter # TRU39FR welded on by an axle shop as it will need to be perfectly square to the axle and the other spindle. I included a video of the #...
    view full answer...

  • Replacement Spindle Washer For Dexter 2,000LB Trailer Axle
  • You should have a spindle washer between the outer bearing and the spindle nut. There are different washers depending on exactly what spindle you have. Washer For 1" Spindle # SW1000 D Washer for EZ Lube Spindles # 5-23 Washer Spindle Tongue # 165863
    view full answer...

  • Correct Replacement Spindle Washer for Dexter 3,500LB Axle
  • A standard spindle will use the Washer For 1" Spindle # SW1000 or the D Washer for EZ Lube Spindles # 5-23.
    view full answer...

  • Can a Trailer Spindle with Grooves Still be Used if Bearing Fits
  • You will have to replace the spindle. Grooves that can't be taken out with emory cloth will eventually cause new bearings to fail which will leave you stranded with a locked up wheel most likely. To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel tracking problems. I would recommend finding a welder...
    view full answer...

  • Replacement 3500 Spindles for Lund Boat Trailer
  • If the spindle is damaged, it'll need to be replaced. The # CE13511 CE Smith hub is compatible with a 3500 lb axle that uses an L68149 inner/L44649 outer wheel bearing and a 10-19 grease seal. For a spindle, you'll need a 3500 lb spindle, but the exact spindle needed will depend on your axle tube and how the current spindles are attached. I'll link to our 3500 lb spindles, but installing a trailer spindle is NOT a do-it-yourself job. Because the old spindle needs to be cut off and the...
    view full answer...

  • Replacement Spindle for Premco Tandem Axle Trailer
  • Our main page for trailer spindles is linked for you. Since your tandem axle trailer is rated for 9500-lbs it uses either 5000-lb or 5200-lb axles. For a 5K axle we offer # TRU57FR which uses a grease seal with an inner diameter (ID) of 2.24-inches, an inner bearing ID of 1.74-inches and an outer bearing ID of 1.25-inches. For a 5200-lb axle we have E-Z Lube spindle # TRU37FR which has the same seal and bearing surface dimensions. Please refer to the items' linked pages for a diagram...
    view full answer...

  • Spindle Replacement Recommendation For Donahue Horse Trailer
  • In order to make sure you get the right components for your Donahue Horse Trailer, we will need some more information. If you are wanting to replace the spindle, the first thing you will need to know is the weight capacity and dimensions of the axle you plan on using the spindle on. Please keep in mind that installing the spindle require welding it to the axle by a certified welder. They use special jigs so that it is concentric and square on the axle or it can cause problems with uneven...
    view full answer...

  • Replacement 2,000lb Trailer Axle Spindles And Hubs For Short Spindles.
  • You will need the BTR E-Z Lube Spindle # TRU44FR to replace your current spindle as there are no longer 4 on 4" hubs available for that size spindle. This will get you a better availability of parts in the future as well. The Dexter Trailer Idler Hub Assembly # 8-91-05UC1-EZ will include new bearings, races, grease seal, lug nuts and E-Z grease cap. The races are going to be pressed into the hub for a simple installation.
    view full answer...

  • What Replacement Spindle Do I Need for a Dexter 69-46 Spindle?
  • As far as removing your current spindle, you will need to grind/drill off the old one. One the old spindle is removed, I recommend the BT8 Spindle for 2,000-lb Trailer Axles # TRU59FR (for a 1-3/8 diameter) or the # TRU94FR (for 1-1/4 diameter). The measurement of the diameter is the stub (innermost tube on the spindle). In order to get the correct size, I recommend measuring the stub of your old spindle once it is removed. I went ahead and attached videos of both of these spindles in order...
    view full answer...

  • Replacement Washer and Nut for EZ Lube Spindle on Escort Boat Trailer
  • The Replacement Spindle Washer - Tang Type for E-Z Lube # 5-101 is the correct fit for your trailer spindle based on the picture and measurement if you want to use a castle nut like # 165686. The alternative option is the Spindle Nut Kit for EZ Lube Axles # RG05-100 which uses a different style retainer for the nut. Either options will work well for you. You may also want the zerk fitting # GZERK to replace the fitting on your spindle which is a confirmed fit since Dexter uses the standard...
    view full answer...

  • Replacement Trailer Spindle for L44643 Inner and Outer Bearings
  • A spindle that uses both inner and outer bearing L44643 makes it a BT8 spindle, # TRU94FR. Please note that welding on new spindles is a precision job and should performed by a qualified welder with experience welding on spindles. The alternative is to replace the axle. Axles are measured from hub face to hub face and from spring seat center to spring seat center. For example, the picture I have included is for axle # T20BTR-EZ-7258.
    view full answer...

  • Replacement 4" Drop Spindle For Dexter 7,000LB E-Z Lube Trailer Axle
  • The #42 E-Z Lube 4" Drop Spindle w/ Flange for 5.2K to 7K Trailer Axles # TRU39FR is the same size as that used on the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles # 8327860. Both will fit the same Dexter Trailer Hub and Drum Assembly # 42866UC3-EZ. It is important to have the replacement spindle welded by a professional in a jig to ensure it is straight and true.
    view full answer...

  • Replacement Spindle Washer, Castle Nut and Cotter Pin for Dexter Spindle
  • The linked page displays all the trailer spindles we offer and specs including weight capacity and thread diameter. All spindles we offer have a 1-inch-diameter threaded portion that accepts a spindle washer like # SW1000 and a castle nut like # 165686. For a cotter pin you can use # 165649.
    view full answer...