bing tracking image

Filter Questions and Answers:

reset filter
Bumper
Bumper
 

Expert Answers about Bumper


  • Westin Fey Bumpers for 1985 Chevrolet C/K Series Pickup
  • We offer a number of aftermarket Fey bumpers for your 1985 Chevrolet C/K Series Pickup so long as it is NOT a flareside/stepside type bed. These appear on the page I linked for you and they include 3 chrome-finish models as well as silver and black bumpers too. The chrome bumper parts we can offer you are: Westin Fey Surestep Deluxe XLT # 21007-92230 Westin Fey Surestep Rear Bumper # 21002-92230 Westin Fey Diamondstep Rear Bumper # 21000-92230 All of these bumpers offer no-drill installation...
    view full answer...

  • RV Bumper Hitch Recommendation Where the Hitch Opening is Below Bumper
  • I have a solution for you, but the RV Bumper 2" Trailer Hitch Receiver # S64025 that you referenced can only be used with the hitch opening on top of the bumper. Instead you would want the Ultra-Fab 2" Motor Home Trailer Hitch # UF35-946401. This hitch can be used with the opening on the bottom of the bumper. Be sure not to exceed the weight capacity of your bumper, check the owners manual of your vehicle for more info on that.
    view full answer...

  • Do You Carry a Swagan Clamp-On or Bolt-On RV/Camper Bumper Hitch
  • Yes, the RV Clamp-On Bumper Hitch is available by itself. It is part # S64025 and I have added a link to it below. Remember, your bumper needs to be a 4x4 inch continuous-weld steel bumper. It cannot be used on spot welded or aluminum camper bumpers.
    view full answer...

  • Folding RV Bumper Mount Cargo Carrier
  • The only folding RV bumper mount cargo carriers that we have are all steel, not aluminum. We do have these available in a few different sizes, which I have listed below. - 24x40 etrailer Cargo Carrier for RV Bumper # e99050 - 24x60 etrailer Cargo Carrier for RV Bumper # e99049 - 24x64 etrailer Cargo Carrier for RV Bumper # e83YR - 24x84 etrailer Cargo Carrier for RV Bumper # e96ZR
    view full answer...

  • Availability Of Hitch Bike Rack To Fit On the Rear Of a Travel Trailer
  • When using a 2-inch hitch adapter that clamps to your 4-inch square RV bumper on a travel trailer you will not want to exceed the limits of your bumper. The bumper towing and tongue capacities may be indicated on the bumper itself, but if not you could check your trailers owner manual or contact the manufacturer of your travel trailer. Also remember when using a bolt-on adapter your bumper needs to be a 4x4 inch continuous-weld steel bumper. It cannot be used on spot welded or aluminum...
    view full answer...

  • Availability of Bumper-Mount Hitch for 2001 Dodge Ram 1500 Pickup
  • We do offer one bumper-mount 2-inch hitch receiver intended for use on a pickup truck, Curt Specialty Hitch # E-3S. This hitch is intended for installation on trucks with a step bumper. The hitch you referenced, part # C19101, is meant for use on a 2-inch RV bumper and so would not be suitable. If your Ram has a step bumper Curt hitch # E-3S will offer you the capacity you need: 500-lbs tongue weight and 5000-lb towing capacity. If you do not have a step bumper you can review the linked...
    view full answer...

  • Availability of Spare Tire Carrier for 5 Inch Bumper
  • If your bumper is 5 inches by 5 inches, we do not carry anything that would work, but if the bumper is not thicker than 3 inches, the Dutton Lainson # DL22120 or the Fulton # FHDSTC0101 would work for you.
    view full answer...

  • Is There a Bolt On, No Drill Receiver For a 2002 Toyota Tundra With Factory Towable Bumper?
  • With your 2002 Toyota Tundra having the towable bumper you would have to replace it with a standard bumper found on models without a receiver or towing bumper. This would then allow you to install a no drill receiver like the Curt # C13180. We do not have a receiver compatible with the towing bumper but you may be able to have one fabricated at a local fabrication shop.
    view full answer...

  • Product Availability for Adapting Jeep Off Road Bumpers to Roadmaster Tow Bars
  • Yes, the part # RM-035 that you referenced is available for purchase. I attached a link below that will allow you to add it to your cart. These Roadmaster adapters will adapt the Roadmaster tow bars to off-road bumpers. This will allow you to connect motorhome-mounted tow bars to the bumper mounts. The Jeep bumper mounts can have either a 7/8 inch or 1 inch diameter hole. The # RM-035-1 is for bumper mounts that are 1 inch thick and the # RM-035 is for bumper mounts that are 3/4 inches thick.
    view full answer...

  • Hitch Receiver for RV Bumpers on 2018 Keystone Cougar 28RDB
  • It is difficult to make an accurate recommendation without understanding the available measurements that would allow fitment. But if you do not think there is enough room for a frame mounted hitch due to a steel tube welded to the bumper, does that steel tube provide solid enough situation for a bumper mounted hitch? What are the dimensions of the bumper on your 2018 Keystone Cougar 28RDB? We have the Stromberg Carlson 2" Hitch Receiver for RV Bumpers, # BA-100. This clamp-on receiver...
    view full answer...

  • Hitch Availability for 1999 Dodge 1500 Conversion Van
  • Several hitches, both Class III and Class IV types, are offered for the different versions of the 1999 full-size Dodge van. The key factor in selecting the right one is the type of bumper on the van, either a standard bumper or a step bumper. The presence of the spare tire is not noted by the manufacturers as affecting the fit; only the bumper type matters. Please see the linked article on bumper types. Versions of the van with existing weld nuts on the frame are not compatible with certain...
    view full answer...

  • Availability of Roadmaster Adapters for Tow Bars to Connect to Off-Road Bumpers
  • Good news! We have both the adapters # RM-035-1 and # RM-035 right here on our website. These Roadmaster adapters will adapt the Roadmaster tow bars to off-road bumpers. This will allow you to connect motorhome-mounted tow bars to the bumper mounts. The bumper mounts can have either a 7/8 inch or 1 inch diameter hole. The # RM-035-1 is for bumper mounts that are 1 inch thick and the # RM-035 is for bumper mounts that are 3/4 inches thick.
    view full answer...

  • Recommended Hitch With Receiver Mounted in Bumper for 2022 Jeep Cherokee Trailhawk
  • The Draw-Tite Max-Frame Trailer Hitch # DT28MR is what you're looking for. This hitch bolts on in place of the bumper beam. The plastic panel in the center of the fascia will be removed for hitch access, so the receiver will stick out from the bumper instead of hanging down below.
    view full answer...

  • Availability of Jeep D-Ring Bumper Mounts for Roadmaster Falcon Tow Bar on a 2016 Jeep Wrangler
  • Good news! We have both the adapters Roadmaster makes for their tow bars # RM-035-1 and # RM-035 right here on our website. These Roadmaster adapters will adapt the Roadmaster tow bars to off-road bumpers. This will allow you to connect motorhome-mounted tow bars to the bumper mounts. The bumper mounts can have either a 7/8 inch or 1 inch diameter hole. The # RM-035-1 is for bumper mounts that are 1 inch thick and the # RM-035 is for bumper mounts that are 3/4 inches thick.
    view full answer...

  • 2006 Toyota Tundra Trailer Hitch Receiver Options for With/Without Factory Tow Bumper
  • A factory towable bumper has additional features/bracing to aid in towing that the other option does not. A factory towable bumper on a Toyota Tundra has a hole located in the the bumper for a hitch ball, on the bumper step area in front of the license plate. The trailer hitch receiver I recommend for your Tundra is the Curt Trailer Hitch Receiver part # 13184 because it will fit models both with the towable bumper and models with the non-towable bumper. This hitch has a Class III rating...
    view full answer...

  • Base Plate Fit for 2012 Jeep Wrangler with Rugged Ridge Aftermarket Bumper with a Winch Mount
  • Base plate fits for your 2012 Jeep Wrangler vary based on the bumper you have installed. We do offer base plates that will work with Mopar and Warn Elite bumpers, as well as on Jeeps that do not have aftermarket bumpers, winches, and guards, but we do not have a confirmed base plate fit for a Rugged Ridge aftermarket bumper with a winch mount. For reference, at right you will find a link to all base plates for the 2012 Wrangler as well as to an article that covers the essentials of flat-towing....
    view full answer...

  • Trailer Hitches Available for 1988 Dodge Ram Pickup
  • The hitch referenced in your question, Draw-Tite 2-inch model # 13368, does not fit your 1988 Dodge Ram pickup but we do have Draw-Tite and other brands of hitches that are confirmed to work on your 1988 Ram. The correct hitch to use will depend on your pickup's bumper type. Please refer to the linked article. If you click on the linked page you'll see all hitches for all versions of your truck and you'll want to select your bumper type using the drop-down menu tool. Select your bumper...
    view full answer...

  • Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Falcon 2 Tow Bar & Jeep Gladiator 2020
  • We have the Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars, # RM-035-1. While we do not have the measurements to confirm that it is a fit for your specific bumper, please review those measurements for fitment to the adapters. These attach to 1" thick shackle mounts where the D-rings are attached. Simply remove D-rings from bumper and attach tow bar to shackle mounts on bumpers that are approved for flat towing. Designed to fit 7/8" and 1" diameter mounting...
    view full answer...

  • Can K2 Detail Snow Plow Mount to 1993 Jeep Wrangler with Above Bumper Mounted Winch
  • Since your winch install hardware is above the bumper you can use the K2 Snow Plow # K2SUMM8826 that you referenced as the install hardware attaches below the bumper and to the frame. All you'd need then is the correct install hardware kit # K284115 and you'd be set.
    view full answer...

  • Replacement Rear Step Bumper For 1982 Ford F100 Pickup Truck
  • I checked with our vendor Westin and confirmed that the only rear bumpers available for a 1982 Ford F100 are the ones listed on our site; you can see them on the link I have attached. You can go with Westin Fey Diamondstep Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21000-92230 for an all steel design or Westin Fey Surestep Rear Bumper with Custom Installation Kit - Chrome Plated Steel # 21002-92230 which has a black textured pad to provide traction when stepping on...
    view full answer...