I went to the warehouse to take a look at the Camco Gen-Turi RV Generator Exhaust System # CAM44461 and found that it extends to 120".
That measurement should tell you exactly how many of the 18" Camco Gen-Turi Extension # CAM44872 you'll need! view full answer...
Typically, when you go to a less-restrictive cat-back exhaust system you gain anywhere from 10-20 horsepower. But every vehicle will respond differently. The gain in power will be the greatest in the higher RPMs. view full answer...
I spoke with my contact at MagnaFlow regarding the Stainless Steel Cat-Back Exhaust System # MF16861 and he stated that while they do not have an exact number for your Infiniti G35, typically one can expect an approximate increase in horsepower between 8-15 hp after installation.
This exhaust system is designed to improve engine performance thereby increasing horsepower along with torque and fuel efficiently. I have attached the installation details for you to check out. view full answer...
The Replacement 90-Degree Exhaust Pipe for Camco Gen-Turi RV Generator Exhaust System # CAM44812 you mention has an inner diameter of 1.53" and an outer diameter of 1.51". view full answer...
The shipping weight of the MagnaFlow exhaust system, # MF15710, is 75 pounds. I have also included a link to the installation instructions for you to view. view full answer...
The space that is between the outer wall of your coach and the exhaust pipe is going to depend on where your generator is and where the exhaust pipe you're connecting to is located. I can tell you that the 90 degree pipe on the bottom of the Camco Gen-Turi RV Generator Exhaust System # CAM44461 extends out 8 inches from the end to where the pipe is bent to extend upwards. If you need more clearance from the coach because the generator exhaust is further under the coach you can use the 30... view full answer...
Yes, I checked with Magnaflow and the MagnaFlow Pro Stainless Steel Filter-Back Exhaust System # MF17972 that you referenced is California legal and is confirmed to fit your 2008 Dodge Ram 3500 Series Quad Cab Long Bed with 6.7L I6 Cummin. view full answer...
The smallest sleeve of the Camco Gen-Turi Transfer Kit, part # CAM44881, has an inner diameter of 1.23 inches and an outer diameter of 1.34 inches. It's 1-1/2 inches long.
This is used to move the Gen-Turi RV Generator Exhaust System, part # CAM44461, to another RV. view full answer...
The Replacement 90-Degree Exhaust Pipe for Camco Gen-Turi RV Generator Exhaust System # CAM44802 you mention has an inner diameter of 1.53" and an outer diameter of 1.51" and while it wasn't designed for use with your Cummins generator there's a chance it could still work if the dimensions match what you need so you would want to check that. view full answer...
Cat-back exhaust systems like the Magnaflow part # MF15353 that fits your 2014 Chevy Camaro with a 3.6 liter V6 will give the vehicle around 10 horsepower or so. If you combine that with a cold air intake and an underdrive pulley you'd likely see around a 20 horsepower gain. Also the car would sound better! view full answer...
The MagnaFlow Cat-Back Exhaust System - Stainless Steel - Gas # MF15136 is a confirmed fit for your 2016 Cadillac CTS 3.6L V6 and a great choice to enhance the sound and performance of your Cadillac. The actual product weight is 46 lbs but the shipping weight with all the packing materials is 79 lbs. The shipping size is 57 x 13 x16 inches. view full answer...
The inlet/outlet/tubing diameters listed from Magnaflow are OD, outer diameter, not ID, inner diameter. If your tubing is 2.5 OD you will have to butt-weld the muffler to the exhaust tubing, the exhaust pipe will not slide into the muffler. Any muffler shop can do this.
The MagnaFlow muffler, part # MF10416 is not designed to be a slip fit muffler. Your exhaust tubing would need to be designed for slip fit mufflers and have band clamps to apply sufficient pressure to seal the system. This... view full answer...
The Rock Tamers Adjustable Mud Flap System, part # ERT00108, offers height, width and angle adjustment to match a range of vehicles. Please note that there must be at least 1-inch of clearance between the back of the ball mount face and the trailer hitch receiver opening to fit the Rock Tamers mounting bracket assembly. (Please see the attached photo.)
The mud flaps themselves measure 24 x 24 inches but their height can be reduced to maintain ground clearance by trimming along the pre-marked... view full answer...
The Blue Ox Adjustable Ball Mount # BLU89XR has a distance of 4-11/16" from the center of the furthest receiver hitch pin hole to the weld on the tube. The shorter hole is 3-7/16" from the center of the receiver hitch pin hole to the weld on the tube.
Since the Hub # ERT057 for the Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2-1/2" Hitches # ERT00110 requires 1" of space you will need to measure the distance from the center of the hitch pin hole on your receiver to the collar... view full answer...
I spoke to my contact at Westin and he informed me that the PRO TRAXX Oval Nerf Bars # 21-23515 that you referenced are only cab length, meaning that they stop at the back of the truck's cab, so they shouldn't interfere with your side mounted exhaust as systems like that usually exit right in front of the rear wheels.
He wasn't able to give me an exact length though. view full answer...
Installing a cat-back system like the Magnaflow Cat-Back part # MF15437 on your 2014 Ford Explorer would not void the warranty. Ford would have to prove that the cat-back caused some type of failure in order for them to void your warranty. Which the likelihood of a cat-back system causing something on your vehicle to fail is extremely low.
The use of aftermarket products is protected by the Federal Magnusson-Moss Warranty Act. The Act states that if something fails on your vehicle and... view full answer...
The batteries in the sensors of the Tuson Towable Tire Pressure Monitoring System # 335TPMS4WIVS that you mentioned will last around 5 years with normal use and are not replaceable.
You'd have to replace the sensor with the part # 335TPMS-SENS which comes with the battery. view full answer...
The 3 inch inlet/outlet diameter on the MagnaFlow Y-Pipe # MF10798 is the outer diameter. Since this is a custom installation I recommend having a muffler shop perform the installation unless you have experience with exhaust systems. view full answer...
I spoke to my contact at Magnaflow and he informed me that this MagnaFlow Stainless Steel Cat-Back Exhaust System # MF16834 that you referenced would give between 9-15 horsepower. When combined with a cold air intake I would imagine you would see a total gain of between 15-25 horsepower.
A programmer would not be required for these modifications but they would help you get a little more power out of your setup. view full answer...
Since this is a universal fit item, it will fit vehicles with 3" inlet and 2-1/4" outlet tubes. If you can let me know what type of vehicle you have I can let you know if we can confirm the fit before your purchase; since it is a universal fit it is designed to fit a wide variety of vehicles.
The MagnaFlow Stainless Steel, Dual Core, Universal Muffler - XL Turbo Series - Satin Finish # MF13278 is a 3 chamber, dual core design to help reduce exhaust noise. These will still be louder than... view full answer...
Go To Results