The B&W Pintle Hook Mounting Plate for 2-1/2" Hitches # BWPMHD14202 does not have any drop and it will take a pintle hook and hitch ball combo that has mounting hole spacing that measures 3-3/8" from left to right and 1-3/4" from top to bottom such as the Buyers Products # 33710055. view full answer...
I was able to get the dimensions you were looking for of the Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with Pintle Mount # 3371809050.
Overall it measures 62 inches wide x 13 inches tall x 22 inches deep; also from the top of the mounting brackets to the first set of mounting holes for a pintle hook, the distance is 4 inches.
Then for a pintle hook you can choose from any of the following, which I confirmed with Buyers Products are a direct fit for the mounting plate of... view full answer...
I went down to our warehouse and measured the Replacement Hitch Ball for Curt Pintle Hook Combo # C48820. The height of the ball inside the pintle is 2-1/2 inches (see picture). The overall height of the hitch ball is 5 inches. view full answer...
The weight capacity of the Curt Pintle Hook with 2-5/16" Ball for 2-1/2" Hitches - 20,000 lbs # C48012 would be decreased when using a 2 inch ball. The Replacement Hitch Ball for B&W Tow & Stow Pintle Hook Combo - 2" # BWTS10051 is the highest rated at 16,000 lbs when used as part of a pintle hook. view full answer...
The reason for the long neck on the curt # C48004 is to help prevent your trailer from hitting your vehicle if ever jack knifed. Sometimes trailers using the pintle setup have a bit bulkier coupler so it could come in contact with your vehicle a little easier compared to the sometimes smaller 2" ball couplers.
The only options we have for the 2" hitch are going to stick out just as much unless you go with a different type of pintle setup. If your concerns are running into the pintle whenever... view full answer...
The distance from the mounting face to the hitch pin hole is approximately 7 inches for the Curt Pintle Hook Mounting Plate for 2-1/2" Hitches # C48348.
With this plate you can use a pintle mounting hook with 9/16" mounting holes, such as the Curt Pintle Hook # C48210.
I have added links to video reviews for you to check out as well. view full answer...
The Buyers Products 15 Ton Combination Pintle Hitch w/ 2-5/16" Ball # BP38FR has a maximum gross trailer weight of 30,000 lbs and max tongue weight of 6,000 lbs. Whether you are using a coupler with the ball or a drawbar/pintle ring the capacity remains the same. view full answer...
The Curt SecureLatch Pintle Hook item # CU57FR weighs 18 lbs. It has a 2-5/16" hitch ball and a 14,000 lbs capacity. This pintle hook and hitch ball combo fits a 2" hitch receiver.
I have linked a review video below so you can see the features of this ball mount demonstrated. view full answer...
No, the Curt item # C48010 is not made in the USA but I have one that is. It is the B&W Tow & Stow Pintle Hook item # BWTS20056. This pintle hook ball mount combo also fits a 2-1/2" hitch receiver. It has a 16,000 lbs capacity for the hook and a 10,000 lbs capacity for the 2-5/16" hitch ball. view full answer...
The 2-5/16" Hitch Ball # BWTS10052 included with the B&W Tow & Stow Pintle Hook # BWTS10056 is only rated for 10,000lbs. This is the only weight capacity 2-5/16" ball available for this hitch. As the pintle places the weight of the trailer on the entire assembly rather than only being on the ball itself it is capable of the higher rating. view full answer...
The Gen-Y Torsion Pintle Hook Mounting Plate # 325-GH-1201 will weigh right at 70 pounds. I included a quick diagram of how the mounting holes measure as well, just to make sure the pintle you have or are looking at will fit.
With that said, if you do not have one already, I can highly recommend the Curt Pintle Hook # C48210. This is rated up to 20,000 pounds and will bolt to the Gen-Y mounting plate perfectly and even includes the hardware needed to do so. view full answer...
Tongue weight isn't considered as much of a factor for pintle hooks because there isn't as much downward force onto the hitch like there is with a standard coupler. With that being said a pintle hook's tongue weight is considered to be 1/4 of the GTW, so for Curt Pintle Hook # C48004 the tongue weight would be 5,000 pounds. view full answer...
I checked with the manufacturer, and the Buyers Products 8 Ton Combination Pintle Hitch with 50 Millimeter Ball # 337BH850MM has mounting holes which are 3-3/8" center to center horizontally and 1-3/4" center to center vertically, which do not match up with the Curt mounting plate you asked about, because it has slightly wider horizontal mounting holes.
What that means is you will need the similar Buyers Products 2" Pintle Hook Mount - 3 Position - 10" shank # 337PM107 which has mounting... view full answer...
The B&W Pintle Hook Mounting Plate for 2 Inch Hitches # BWPMHD14004 referenced in your question has mounting holes that measure 1-3/4 inches apart on center vertically, and 3-3/8 inches apart on center horizontally. I have attached an image to help clarify these dimensions.
The mounting plate is 12-1/4 inches tall and 5 inches wide and can be used in the drop or rise position in your 2 inch trailer hitch receiver.
For a pintle hook, I recommend looking at the Buyers Products Pintle Hook... view full answer...
I went to our warehouse and measured the B&W Pintle Hook Mounting Plate # BWPMHD14005.
I measured the center to center horizontal hole spacing at 3-3/8-inches so it will work well with Pintle Hook # C48210. view full answer...
The mounting holes on the Magnum Pintle Hook Mounting Plate Adapter # TLM9002 are 3-1/2" horizontal and 1-3/4" vertical center on center. This is the same standard dimensions for virtually any pintle hook attachment, like part # C48210, which will be compatible. view full answer...
The TowReady Bolt-On Pintle Hook # 63105, will work for you in the capacity that you want. It is rated for 30,000 lbs of GTW (gross towing weight). You will have to bolt this product directly to the frame of the tow vehicle or to a reinforced bumper to retain its 30,000 lb GTW as long as the tow vehicle can handle the capacity of the load being towed. Using a pintle hitch mount that attaches to a hitch receiver on a vehicle will reduce the weight capacity to 10,000-12,000 lbs. view full answer...
Yes, the 20K weight rating of the Blue Ox Adjustable Ball Mount with Pintle Hook # BLU25XR is the same whether you're using it as a standard hitch ball or in the pintle hook application.
This is a nice, solid piece of towing gear that I recommend securing with the InfiniteRule Hitch Lock # 34061072-D to deter opportunist thieves from getting a little greedy.
Attached are review videos for you to check out! view full answer...
The Curt # C48006 pintle hook combo measures 11-3/4 inches from the hitch pin hole to the center of the ball hole.
The longest pintle hook combo we offer would be the B&W # BWTS10056 that offers a 12 inch distance between the hitch pin hole and the center of the hole where the 2-5/16 inch trailer ball mounts. The hook has a 16,000 lb capacity, but you'd be limited to the 10,000 lb weight capacity of the trailer ball.
I'm sorry to say that we don't offer a 14 inch length pintle hook like... view full answer...
I've edited a photo for you that shows the bolt hole pattern of the Buyers Products # 337BP200 Swivel Pintle Hook. If you click the provided link, you can see a product description video featuring the pintle hook. view full answer...
Go To Results