Per my contact at Hopkins, the wires used with the Engager Trailer BreakAway Kit with Charger and Tester, part # 20099 are all 16-ga wire except the battery wire which is 14-gauge.
The wire form the breakaway switch to the box is 16-gauge. view full answer...
I spoke with my contact at Hopkins to get the dimensions of the battery box in Engager Trailer BreakAway Kit, # 20400. The box measures 8 inches long by 4 inches wide by 6-1/4 inches tall overall. I have included a link to the installation details for this kit for you to view. view full answer...
Yes, I spoke with my contact at Hopkins and he informed me that this Engager Trailer BreakAway Kit # 20099 is on a 5 amp circuit and should work well for you.
I attached installation instructions for this product for you to check out also. view full answer...
The Engager Trailer BreakAway Kit with Charger and Tester part # 20099 is weather resistant but not waterproof. Which means that you would not be able to submerge the battery and box in water but it would withstand inclement weather.
Ideally your best option would be to mount the battery in a location that is up high enough that it would not get submerged while backing the trailer in the water. Or at least close enough to the coupler that it would not get submerged.
I attached an FAQ... view full answer...
The main battery box included in the Bright Way Push-to-Test Trailer Breakaway Kit # 3802308 is 6-1/2 inches wide by 4-3/4 inches deep by 4-7/8 inches tall. The mounting hole centers are 5.9 inches apart. The wire leads on the breakaway switch are approximately 36 inches long.
If you forward to about the 2:50 mark on the video I attached, it will show these measurements, but I've also attached a photo for reference. view full answer...
I spoke with Bright Way, and they informed me that the black and blue wires that are coming out of the Replacement Breakaway Switch for Bright Way Trailer Breakaway Kits # 3802348 is 16 AWG.
Attached is a review video for you to check out as well. view full answer...
The clamp of the Curt Breakaway kit part # C52026 that you referenced is 3 inches wide and 1-1/2 inches tall. It would work well on a 2 inch wide frame rail. view full answer...
The overall dimension of the Curt Push-To-Test Trailer Breakaway Kit part # C52044 are 6-1/2" long x 4-3/4" wide x 5" tall. I have attached a review video for you which showcases all of these dimensions. view full answer...
The mounting holes are 5-1/2 inches apart horizontally and 3-1/2 inches apart vertically on the Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery - Side Load # 3802346. view full answer...
The Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Side Load # 20099 or Top Load # 20400, have about 16 inches of wire outside the battery housing. I went out to our warehouse to measure the length of those 3 wires for you. view full answer...
The Tekonsha Push-To-Test Trailer Breakaway Kit # 50-85-313 referenced in your question weighs just 5 pounds and the Pro Series Standard Brake Winch # PSKR15000301 you also mentioned weighs right around 8 pounds.
I have attached a couple short video demonstrations on these products that you can also take a look at. view full answer...
The overall length of the cable included with the Titan Breakaway and Parking Kit for Drum Brakes # T2385200 is a bit over 15-feet (183-inches). Half of this length will be on each side of the trailer.
My contact at Titan confirmed that the cable cannot be cut but that there is 2-1/2-inches of adjustment possible by rotating the threaded u-shaped yoke at the center of the main cable. This yoke is shown in the photo I linked for you. This will shorten both sides of the long cable by the... view full answer...
The Tekonsha Push to Test Breakaway Kit, # 50-85-313, is large enough to house a 12 volt battery like # UB1250, which is 3-1/2 inches x 2-3/4 inches x 4 inches. The box will be slightly larger then this in order to accommodate the battery. The box is this particular kit is not available as a stand alone item, but we do have others that are.
Take a look at the Replacement Battery Box for Breakaway Kit, # 34420215. This box will be the same size as the one listed above. We also have Replacement... view full answer...
The Fastway Zip Coiled Trailer Breakaway Cable item # FA80-01-2206 is a universal fit and is just the pin for the Fastway Zip Trailer Breakaway Switch item # FA80-00-2060. As long as you Esco system works by just completing a circuit the Fastway Zip Pin will work for you. view full answer...
We do have a battery box though the Curt battery box you referenced does not have the correct length for your battery, which is just over 5-3/4" long. Instead, you will need the Replacement Clamp-On Battery Box for Tekonsha Trailer Breakaway Kit # TK2018 because it measures 5-15/16" long x 5-1/16" tall x 3-3/8" wide.
I have added a link to a video review of this battery box for you to check out as well. view full answer...
My contact at Titan confirmed that the cable in their Breakaway and Parking Kit for Drum Brakes # T2385200 is not intended to be cut but that there is 2-1/2-inches of adjustment possible by rotating the threaded u-shaped yoke at the center of the main cable. This will shorten both sides of the long cable by the same 2-1/2-inches. view full answer...
I'll be happy to help you. Our website can be overwhelming sometimes with Jeep parts and all of the options. Since you already have the 7 way to 6 pin cable you will need the following parts to control your 1997 Jeep Wangler TJ's lights:
RoadMaster 6-Wire Trailer Connector - Vehicle End item # RM-910030-7
Roadmaster Universal Hy-Power Diode Wiring Kit item # RM-152
It sounds like you have something similar to the Blue Ox Base Plate Kit item # BX1120. Ours don't have the Roadmaster Bent... view full answer...
I checked one of the Hopkins Replacement Box with LED Lid for Engager Breakaway Kit # HM20121 and measured the 3 pigtail wire leads. Form the outside of the box the leads extend 24-inches. view full answer...
The dimensions for the Replacement Box with Non-LED Lid for Engager Breakaway Kit, # HM20120, are:
Bottom Inside
4-1/4 inches wide x 4 inches front to back x 3-1/4 inches tall
Top Inside
4-11/16 inches wide x 4-3/8 inches front to back
Outside Overall
5-1/8 inches wide x 6-1/4 inches front to back x 4-1/8 inches tall
I have also made a short video showing the dimensions. view full answer...
The Battery Box for the Hopkins Engager trailer break away system measures 5-5/8 inches wide by 5-1/8 inches tall by 4-1/8 deep.
If you click the provided links, you can see a trailer breakaway system FAQ article and an install video that you might find helpful. view full answer...
Go To Results