bing tracking image

Filter Questions and Answers:

reset filter
Truck Bed Tents
Truck Bed Tents
 

Expert Answers about Kia Truck Bed Tents


  • Can Rightline Truck Bed Tent for 2019 Toyota Tacoma With 5 Foot Bed Work With Tonneau Cover
  • In order to use the Rightline Truck Bed Tent # RL110765 in your 2019 Toyota Tacoma's 5 foot bed, you will need to remove your tonneau cover. The reason for that is the tent won't be able to securely install while the cover is folded up as there would be interference with your tonneau cover. I have added a link below to a video review for you to check out as well if you like of the Rightline Truck Bed Tent # RL110765.
    view full answer...

  • Can the Rightline Truck Bed Tent RL110710 Install in Truck Bed with Rails
  • The Rightline Truck Bed Tent # RL110710 would work fine if you happen to have a set of fifth wheel rails or any other type of rail in the bed of the truck. The tent attaches to the top of the bed rail but can also work around products installed on the rail due to it's universal nature. If you check out the video I attached you can see how it installs in a similar truck.
    view full answer...

  • Rightline Truck Bed Tent that Fits 1977 Chevy K10 Standard Bed
  • Yes the Rightline Truck Bed Tent # RL110730 is a fit for your 1977 Chevy K10 with a standard bed length.
    view full answer...

  • Does Rightline Truck Bed Tent Fit 2018 Ford F-150 with BakFlip Tonneau
  • Yes the Rightline Truck Bed Tent # RL110730 that you referenced will fit with the BakFlip MX4 tonneau you have installed on your 2018 Ford F-150.
    view full answer...

  • Truck Bed Ladder Rack Tent Option For A 2018 Ford F-150
  • I took a look at the Adarac Pro Series Custom Truck Bed Ladder Rack # A4000964 you mention, and it doesn't look like adding a third bar is going to be an option, however the ladder rack you have right now should have more than enough capacity to support a tent in the bed of your 2018 Ford F-150. A great tent option to work with your setup is the Yakima SkyRise HD Tent for Roof Rack Crossbars # Y07436. This tent has a two adult sleeping capacity, a tent weight capacity of 400lbs, and includes...
    view full answer...

  • How Do Rear Vehicle Doors Fit in the Rightline Gear Truck Bed Tent # RL110907
  • To see how the rear door of your 2007 Jeep Liberty would fit into the Rightline Gear Truck Bed Tent # RL110907 check out the pic I attached. It shows this tent being used in a similar vehicle.
    view full answer...

  • How Do the TracRac Sliding Ladder Racks Attach to Truck Bed Rails
  • I attached a picture that shows an exploded diagram of how the TracRac Ladder rack part # TH43003XT-501 installs to a truck bed. Basically the rails install down into the stake pockets of the bed rails to provide a secure attachment. This is one of the nicest ladder racks on the market that would work well for you. The sliding uprights make this rack also very versatile. The weight capacity of this rack is 1,250 lbs so it would have more than enough capacity.
    view full answer...

  • Installing A Pioneer Platform On A Thule Xsporter Pro To Carry A Thule Basin Wedge Rooftop Tent
  • I do have an option for you if you want to use a Rhino-Rack Universal Pioneer Platform Rack for Crossbars - Aluminum - 58" Long x 47" Wide, part # RR42115BF, to carry a Thule Basin Wedge Rooftop Tent and Cargo Box - 2 Person - 600 lbs - Black and Olive Green, part # TH92VY. We have gotten this question before. The Rhino-Rack representative let us know there is not an attachment available to install a rooftop tent to a Pioneer Platform since most of these tents are designed to attach to...
    view full answer...

  • Yakima SkyRise HD Tent for Roof Rack Crossbar and Travel Speeds
  • The Yakima SkyRise HD Tent for Roof Rack Crossbars, # Y07437, is a fantastic product. This heavy-duty tent sets up in minutes and provides solid footing and steady support on varying terrain. Yes, if properly installed the vinyl cover does provide sufficient results to ensure things stay dry in harsh weather. While there may always be an element of concern in the most extreme conditions, under most situations, including a rather substantial rain combined with driving speeds, you can be...
    view full answer...

  • Using the Rightline Gear SUV Tent with 2011 Honda Pilot Without Draining the Vehicle Battery
  • In order to have the rear hatch of your 2011 Honda Pilot open for an extended period of time while using the Rightline Gear SUV Tent # RL110907 and not drain your battery, you will likely need to disconnect the vehicle battery. For an easier way to disconnect the battery, you can use the Deka Lead Quick-Disconnect Battery Terminal # DW05312. This will allow you to use a hand knob to disconnect the vehicle battery. The Lead Quick Disconnect is designed to fit top-post batteries on cars,...
    view full answer...

  • Does SportRack Pop-Up Camper Roof Rack SR1020 Require Drilling for Installation
  • Roof racks made for the tops of pop-up trailers and in-bed campers do typically require drilling for installation. The SportRack # SR1020 rack is intended for camper tops that do not have rounded or curved edges on the roof. The mounting brackets require a 90-degree mounting point and the camper width cannot exceed 85-1/2-inches. Based on my research your Palomino has straight roof sides that will be compatible. The kit includes all required parts. Each crossbar has three different notches...
    view full answer...

  • Will the Roofnest Sparrow XL Roof Top Tent Fit On A Malone EcoLight Sport Trailer
  • Though you will need to contact Roofnest about the hardware as it is not a part we currently carry, there shouldn't be an issue. From looking at the instructions, it will fit standard crossbars that are 40 inches wide with a minimum crossbar spread of 30 inches. The Malone EcoLight Sport Trailer # MAL53FR will have crossbars that are 58 inches wide and has a spread of 38-1/2 inches. They will also be 1-1/4" x 1-1/4" bars and will not be an issue at all. The only problem will be the weight...
    view full answer...

  • Recommended Distance Between Feet for Thule TracRac CapRac Ladder Rack for Camper Shell/Truck Cap
  • According to the instructions for the Thule TracRac CapRac Ladder Rack for Camper Shell/Truck Cap # TH29200XT you'll want the feet to be about 27-1/2" apart from each other both front to back and side to side. Thule says "about" that measurement so if it's a little more or less you'll be okay.
    view full answer...

  • Installing a Brake Controller on a 2002 Ford Ranger with 4-Way Flat Trailer Connector
  • Installing a brake controller on your 2002 Ford Ranger with a 4-Way flat connector at the back isn't too difficult at all. I am confident that you can perform this installation yourself at home. All you will need is the brake controller itself and an installation kit. For a brake controller the Primus # TK90160 is a great choice. This is a proportional controller that applies the trailer brakes in proportion to how much the truck is braking. For an installation kit you will need # ETBC7....
    view full answer...

  • How is UWS Truck Bed Chest # UWS01029 Installed in Truck Bed
  • For chest style toolboxes like the UWS Truck Bed Chest # UWS01029 that you referenced you'll want to drill through the bottom of the box and truck bed to secure it using nuts and bolts. Other boxes will sometimes use j-hooks to secure in the truck bed but the chest style boxes have to drill through the truck bed.
    view full answer...

  • How Does Thule TracRac Side-Mount Truck Bed Ladder Rack Attach to a Truck Bed
  • The Thule TracRac Side-Mount Truck Bed Ladder Rack # TH14750 requires drilling into the truck bed and using the included hardware for installation in a truck bed.
    view full answer...

  • BedRug Custom Truck Bed Mat Installation In A 2021 Honda Ridgeline
  • The BedRug Custom Truck Bed Mat - Bed Floor Cover for Trucks with Bare Beds or Spray-In Liners # BMH17RBS that we carry does not require drilling or or push-in fasteners because it is only for bare truck beds or those with spray-on liners and will not fit trucks with existing drop-in liners. The push-in fastener style you saw on the BedRug site was for beds with a drop-in liner already installed. This truck bed mat will utilize the included Velcro strips and adhesive to mount to the bed...
    view full answer...

  • How To Strap Down the Etrailer Cargo Bag # 988501 In The Bed Of a Truck
  • To tie down the etrailer Cargo bag, part # 988501, inside your truck bed I would recommend to inspect the inside of your truck bed and see if there are any tie-down points or hooks located at the front, back and/or sides of the truck bed. On many of the newer trucks they will usually have tie-down points located in the truck bed to tie-down any cargo. You could use the straps that come with the cargo bag or you could also use a truck bed cargo net that will tie-down and trap or hold your...
    view full answer...

  • How Is Reese 5th Wheel Trailer Hitch Installed In Truck Bed
  • The Reese 5th Wheel Trailer Hitch, part # RP30051 attaches to bed rails that are installed in the bed of a truck. This is a 2-jaw sliding hitch that has a 4-way pivoting head. This hitch has a 16,000-lb gross towing weight capacity and features 10-inches of travel front to back. The installation of the bed rails do attach to the truck frame and require drilling through the truck bed floor. Since there are universal or custom installation kits available for most trucks, if you want to...
    view full answer...

  • Can the BedRug Custom Truck Bed Mat be Cut for 5th Wheel Base Rails in the Truck Bed
  • Yes, you can cut the BedRug Custom Truck Bed Mat, # BMQ99LBS, to expose your fifth wheel base rails that are bolted to your truck bed. I spoke with my contact at BedRug and she told me that they recommend cutting out slots for fifth wheel base rails if you intend on keeping them mounted in the truck bed.
    view full answer...