bing tracking image

Filter Questions and Answers:

reset filter
Bumper
Bumper
 

Expert Answers about Bumper


  • How Long is the Warranty of the Westin Perfect Match Bumper # 31018
  • The Westin Bumper part # 31018 that you referenced has a 3-year warranty that covers any manufacturing defects.
    view full answer...

  • Turn Signals On Bumper 7-Way Dont Work but Turn Signals on In-Bed 7-Way Do Work
  • I do have a replacement trailer connector for you in the Trailer Connector Socket part # HM40975 but if you need the wiring harness that leads to this plug then you would need to contact the dealer. The in-bed and bumper trailer connectors use the same fuses and relays therefore the issue is going to be most likely where the two harnesses branch off from one another or from that section of wires forward to the bumper 7-way. I recommend that you test the turn signal pins inside the bumper...
    view full answer...

  • 2017 GMC Sierra 3500 Replacement for Bumper 7-Way Trailer Socket
  • Since the in-bed 7-Way is working on your 2017 GMC Sierra 3500 it sounds like you need to simply replace the 7-Way at your bumper. If the bumper 7-Way had a bad ground it would be causing more issues than just the running lights to not work. You can try locating the ground near your bumper and just make sure it's secured to a clean, bare-metal surface just to make sure, but you should just need to replace your OEM connector with the Hopkins # HM40975 and that will take care of your issue!
    view full answer...

  • Does Curt Bumper Hitch # E-100 Have Ability to Tow Trailer
  • Yes the Curt hitch part # E-100 has a towing capacity of 3,500 lbs so it can tow. You'd need to verify that the bumper you install it on as well is rated for towing and stay under the capacity of the bumper as well.
    view full answer...

  • Trouble Re-Installing the Center Hitch Cover with the Curt Hitch # CU29FR on a 2021 Buick Enclave
  • Sorry to hear about this! I am guessing you are referring to the Curt Hitch - 2" # CU29FR. If this is the hitch you have installed, the most common issue with not being able to install the center hitch cover over the hitch results from not lining up the rest of the bumper correctly. Any little variation with how the bumper is attached to the rear of your vehicle can affect the fitment of that center piece. The best route is to remove and re-install the bumper to ensure fitment. I went...
    view full answer...

  • Could Longer Bolts Be Used to Install Fulton Spare Tire Carrier # FSTC1000301 on 4 Inch Bumper
  • Yes, with longer bolts you could attach the Fulton Hi-Mount Spare Tire Carrier # FSTC1000301 to a 4 inch by 4 inch frame/bumper. We had a customer leave a review on this mount and he said that with longer bolts he was able to use this mount on a 4 inch by 4 inch bumper and it worked fine.
    view full answer...

  • Air Spring Engages Internal Jounce Bumper Too Early On 2014 Toyota Tundra
  • Air Lift does not sell an Air Spring that does not include an internal jounce bumper, as they are integrated with the design of the product. This is a known issue with Tundras', and many people have reported that the Firestone Ride-Rite Air Helper Springs - Double Convoluted # F2445 for 4 wheel drive models, and # F2445 for two wheel drive models to be much better.
    view full answer...

  • Solution for Trailer that Bumps Vehicle Bumper While Backing Up to It
  • While we don't have a product that does what you are looking for I can help you. I am familiar with what you are describing. Once you back your vehicle up and get it perfectly lined up it moves several inches after you put it in park and release the brake...which screws up everything and sometimes bumps the tow vehicle. If you have a great parking brake just apply that once you get lined up and the vehicle won't move. Or, and this took some trial and error on my part, you can put the vehicle...
    view full answer...

  • Troubleshooting In-Bed 7-Way Trailer Connector on 2019 Ford F-350
  • An aftermarket in-bed wiring harness like # 41157 installs by plugging inline between the factory harness and the factory 7-way mounted on the bumper as shown in the video I've linked for you. As the connector on the bumper is working okay, check the connection at the back of the in-bed 7-way. Make sure that plug is fully seated, some times that's a tight fit and you'll need to push really hard to make sure the plug and the harness are fully seated together.
    view full answer...

  • No Running Lamp Circuit Signal from Rear Bumper or In-Bed Trailer Connector on 2017 Ram 2500
  • The trailer connector located in the truck bed is typically daisy chained together by plugging inline between the factory harness and the 7-way at the rear bumper. If this connection isn't secure or if moisture has gotten into the connection and caused the connections to corrode, it would explain the problem you're having. This is the most likely culprit if the fuse in location # 29 in the main fuse box hasn't blown.
    view full answer...

  • Installing 7-way Trailer Connector in Stock Location on 2014 Honda Pilot
  • Installing the # 118265 7-way connector would involve using a hole saw to make a hole to mount the trailer connector, if you wish the installation to look like a stock install. I can understand why you'd be reluctant to cut a hole in the bumper of a brand new vehicle. We've had several reviews from folks that simply used a 2 inch hole saw to cut through the bumper, and from what I've read, it didn't sound like a difficult process. I guess you'll need to decide if the extra cost of the Honda...
    view full answer...

  • Troubleshooting Pinched Airline with Firestone Coil-Rite Air Springs on a 2008 Jeep Liberty
  • The hole that gets drilled into the jounce bumper mount does not have a set measurement on where it should be located. If shortening the line would prevent it from getting pinched when the suspension is lowered I would do that as that should be the easiest. Since you plan on shortening the line what you could do is cut a slit in the air line on the barbed fitting to remove the line and then cut the line to the length you want and reinsert the line. Thanks for the feedback on drilling...
    view full answer...

  • Noise After Draw-Tite Trailer Hitch Install On 2022 Mazda 3 Hatchback
  • There is no trimming required for the Curt Trailer Hitch Receiver part # C98BR on a 2022 Mazda 3. The only thing we typically see creating noise after install is heat shields and mufflers. The bumper and hitch are both fixed so this is not likely the issue. That said, I have attached a help article below which goes over some things you can do to help cut down noise from the exhaust if this ends up being the issue.
    view full answer...

  • Is There Supposed to Be a Small Gap Right Behind Where the Bolt Holds the Bumper?
  • I confirmed with my contact at Curt that this gap is normal for fitting the Curt Class III Hitch # 14374 on a 2018 RAM 1500.
    view full answer...

  • Troubleshooting Curt Hitch # C13098 Not Being Wide Enough to Fit Over Brackets of Vehicle
  • It is very possible that your Curt Hitch part # C13098 got bent during shipping and that is why it doesn't want to fit over the brackets of your 1999 Isuzu Trooper. Typically we recommend people use an open stairwell or a large vice to apply leverage to the brackets so that they can be bent back. As long as the metal doesn't crease or paint doesn't flake off during either the initial bend or the bending back the integrity of the hitch will be intact.
    view full answer...

  • How to Get the RhinoFLEX RV Sewer Hose w Swivel Fittings to Fit in a Bumper
  • I spoke to my contact at Camco and he said that if the lug end of the part # CAM39761 doesn't want to fit into the bumper of your trailer your best option would be to grind down two of the lugs and the hose would then fit.
    view full answer...

  • Troubleshooting Trailer Lights That Have Power But Are Not Working
  • It sounds like you have power going back to the light, but the light is not working. This is typically an issue with the light ground. If you have the light grounded to the bumper, I recommend running the trailer light ground up to the main trailer ground. If this does not provide a solution, let me know and I will be glad to look into further solutions for you.
    view full answer...

  • No Power To 12V Auxiliary Power On Factory 7 Way Connector 2018 Ram 1500/2500/3500
  • If you are receiving no power at the receptacle but you are receiving power at the bumper 7 way connection then it is unlikely it is a blown fuse. More than likely it is a damaged wire or a bad connector, to determine this start by tracing the black wire associated with the vehicles 7 way 12V auxiliary wire inspecting as you go for breaks or frays in the wire. If your problem still is not resolved after that, you can run a new line using # 10-1-1 from your 7 way connector to your vehicles...
    view full answer...

  • Troubleshooting Factory In-Bed 7-Way Gooseneck and 5th Wheel Trailer Connection on 2017 Ram 3500
  • The in bed wiring harness on your OEM 2017 Ram 3500 connects to the same circuit as your rear bumper 7-way. I recommend removing the T-connector from behind your bumper and inspecting the pins for anything bent. The use some dielectric grease like # 11755 to keep moisture and debris out and reconnect it. Do the same behind the plug in the bed and then test for function. If you don't have the 12V power at that point, then you will want to trace the wire to find the short or replace the...
    view full answer...

  • Troubleshooting Plug-N-Tow Wiring Harness Part # 40455 on 2006 Ford Escape
  • My guess is that your Escape was not equipped with the Tow Package from the factory. The plug for the Hoppy wiring harness will be present behind the bumper, but unless the Escape has the tow package it will NOT be active. To activate, a relay will need to be placed into the wiring block located behind the dash. From what I understand, the relay would need to be obtained from your Ford Dealer. If your Escape is not equipped with the Tow Package, your best bet would be to use the T-1 Vehicle...
    view full answer...