bing tracking image

Filter Questions and Answers:

reset filter
Bumper
Bumper
 

Expert Answers about Subaru Bumper


  • Rear Bumper for a 2003 Dodge Ram Van 1500
  • I do have a rear bumper you can use on your 2003 Dodge Ram Van 1500 but we do not carry any OEM parts. You would need to contact your local dealer's parts department in order to obtain an OEM bumper. However, you can use the Westin Fey Surestep Rear Bumper part # 76001 which is the bumper you referenced and very similar to the one in the attached photo with the Installation Kit for Westin Surestep Bumpers part # 92230. The bumper brackets will be an exact match for the bumper but you will...
    view full answer...

  • Recommended Base Plate Adapters for 2015 Jeep Wrangler Sport with Winch Bumper
  • For your 2015 Jeep Wrangler Sport with winch bumper you do not need to remove your bumper, but you will need to utilize the D-rings of your bumper to use a tow bar. Make sure your bumper manufacturer confirms compatibility flat towing with their bumper. You will either need the Adapter for Jeep D-Ring Bumper Mounts - 3/4" Thick # RM-035 or the Adapter for Jeep D-Ring Bumper Mounts - 1" Thick # RM-035-1. Either of these adapter will work well with the Roadmaster Falcon 2 Tow Bar # RM-520...
    view full answer...

  • Hitch Recommendation for a 1976 Ford F150 with a Deep Drop Bumper
  • A roll pan bumper is a bumper that basically makes the rear bumper look as if it does not stick out further than the rest of the truck and that is molded into the rear of the truck. Its basically a cosmetic modification that you see on a lot of lowered and/or show trucks. What you have is definitely a deep drop bumper. Check out the FAQ article I attached on bumper types for you to check out. With that being said, you will need a hitch designed for trucks with deep drop bumpers like the...
    view full answer...

  • Rear Bumper Hitch Solution for 4 inch Bumper with Limited Clearance Above Bumper
  • Due to the limited clearance you have above your rear bumper you'd need to install a bumper hitch that hangs below the rear bumper like the Buyers Products # 3371804060 as the # UF35-946401 needs to install above the rear bumper.
    view full answer...

  • Can Jeep Wrangler with Aftermarket Bumper be Flat Towed from D-Rings
  • It really comes down to what the aftermarket bumper manufacturer will endorse and say is okay. If the bumper manufacturer states that their bumper can have it's D-rings used for connecting a tow bar it would be okay to do so. If the D-rings are 3/4 inch wide you'd need the D-ring adapter part # RM-035 or if they are 1 inch wide you'd need the part # RM-035-1.
    view full answer...

  • Replacement Rear Bumper for a 2001 Dodge Dakota SLT Quad Cab
  • For your 2001 Dodge Dakota SLT we have a couple of replacement rear bumper options. You can use a Perfect Match bumper, chrome-plated steel, # 31012. This bumpers will install using the factory bumper brackets. The more universal fit bumpers, such as # 63000-93800, will not fit quad cab models.
    view full answer...

  • Could Bumper Hitch E-100 Fit a 3 inch Bumper
  • You could have 1 inch spacers put on the bumper so that the 4 inch bumper hitches we offer like the # E-100 would fit. Metal 1 inch spacers would be what you would need. Ideally you would have them welded to the bumper.
    view full answer...

  • Recommended RV Trailer Hitch to Tow 4 Wheeler on Small Trailer
  • As long as the bumper on y our 2016 Coachmen Catalina Trailer is rated to tow a small trailer, then the bumper mount Curt RV Bumper 2 Inch Trailer HItch Receiver # E-100 will work. The receiver itself has a 350 pound tongue weight and 3,500 pound gross towing weight capacity, however I do recommend checking with the trailer manufacturer to verify the capacity of the bumper.
    view full answer...

  • Can a Cargo Carrier be Used on a Bumper Mount Hitch to Carry Generators on an RV
  • If you plan on carrying generators I would not use a bumper mounted hitch. The fact that the bumper is rated for a bike carrier says to me that you don't want to put anything else on it. A loaded bike carrier isn't all that heavy. But a cargo carrier with generators on it can create a lot of stress. A frame mounted hitch should be used. I included a link to the frame mount RV hitches we carry. Regarding how far out the basket would be on a bumper mounted hitch it depends on the hitch....
    view full answer...

  • Blue Ox Tow Bar Adapter for Jeep Tow Bumper
  • There are a couple choices for you that will be based on the bumper you have. Blue Ox Aftermarket Bumper Adapter # BX88358 -Bumper tab thickness: 3/4", 7/8", and 1" -Pin Hole diameter: 1" Blue Ox Aftermarket Bumper Adapter # BX88357 -Bumper tab thickness: 5/8" - 1" -Pin Hole diameter: 7/8" If none of these match what you currently have please let me know what you have. There may be other options available for you. You will also want to check to ensure that your bumper on the Jeep is...
    view full answer...

  • Replacement Front and Rear Bumpers for a 2017 Jeep Wrangler
  • Yes! We have numerous replacement bumper options for your 2017 Jeep Wrangler 2-door. I have included a link to them for you. For the rear bumper I recommend the Rampage recovery bumper # RA88606. It has a rugged textured finish and swing out spare tire carrier. For a matching front bumper I recommend # RA88510. It features the same rugged finish so they bumpers will match.
    view full answer...

  • Curt Trailer Hitch Recommendation for Fitting Bumper at Rear of Camper
  • We have trailer hitches from Curt that are designed specifically for attaching to a camper's bumper. If the bumper is 4 inch by 4 inch we have the part # E-100. If the bumper is 4 inch by 2 inch we have the part # C19101.
    view full answer...

  • Recommended Trailer Hitch for 2004 Chevy Silverado 1500 with Aftermarket Rear Bumper
  • I have the perfect option for you in the Curt Trailer Hitch Receiver part # 13339 which is a confirmed fit for a 2004 Chevrolet Silverado 1500 model and actually designed specially for models with an aftermarket bumper. As you can see, there are no mounting tabs to attach to the bumper so you will not have any worries here and the receiver tube has a deep drop to clear larger aftermarket rear bumpers. The above Curt Trailer Hitch Receiver is actually the only option we have that is designed...
    view full answer...

  • Easy to Install Trailer Hitch for 2011 Cougar 24.5 5th Wheel with 4 inch Square Bumper
  • Sounds like you have the standard 4 inch square bumper at the back of your 2011 Cougar that is getting used to store your sewer pipe. The easiest hitch solution actually will be to go with a hitch that installs on the bumper like the Curt # E-100. This easily installs over the bumper with the included hardware and has towing capacities of 3,500 lbs trailer weight and 350 lb tongue weight. I attached a picture that shows what the hitch looks like installed as well as review video. This won't...
    view full answer...

  • RV Bumper Hitch Recommendation that Can Mount Below Bumper
  • I have a solution for you, but the RV Bumper 2" Trailer Hitch Receiver # S64025 that you referenced can only be used with the hitch opening on top of the bumper. Instead you would want the Ultra-Fab 2" Motor Home Trailer Hitch # UF35-946401. This hitch can be used with the opening on the bottom of the bumper. Be sure not to exceed the weight capacity of your bumper, check the owners manual of your vehicle for more info on that.
    view full answer...

  • Recommendation for a Bumper Mounted Trailer Hitch for an RV, Trailer, or Motorhome
  • It sounds like the Stromberg Carlson 2" Motor Home Hitch Receiver, part # BA-100 would be your best bet. This receiver will fit bumpers up to 4 by 4-1/2 inches. This receiver is designed for mounting accessories like a bike rack, and not for towing purposes. It has a 200 lb capacity. You will want to make sure your bumper is rated for this application and do not exceed the capacity of the bumper or hitch, whichever is lower.
    view full answer...

  • Are the Hitches for a 2007 Dodge Sprinter with Standard and Step Bumper the Same
  • The trailer hitch options for a 2007 Dodge Sprinter are different for models with the factory step bumper and models with the standard bumper. The two are not interchangeable so if you have the factory step bumper then you'll need the Curt Trailer Hitch Receiver part # 13358 or if you have the standard bumper then you'll need the Curt Trailer Hitch Receiver part # C13388.
    view full answer...

  • Could Pre-Drilled Round Rubber Trailer Bumper # D3-96 Replace Bumper with Different Hole Spacings
  • What you'd want to do is drill holes in the Pre-Drilled Round Rubber Trailer Bumper # D3-96 to match the mounting holes of your trailer and you'd be set. The bumper is rubber so it would be easy to drill. The pre drilled holes of this are 11 inches apart so it wouldn't match perfectly.
    view full answer...

  • Bumper Mounted Spare Tire Carrier Recommendation for Lance Trailer
  • The bumper mounted spare tire carriers like the part # UF15-954730 are designed to fit 4 inch by 4 inch square bumpers that are continuously welded. Check out the picture I attached that shows this carrier mounted to the style of bumper it is compatible with it. When you said you have a flat bumper I am assuming this is what you meant.
    view full answer...

  • Will Folding, Bumper Mounted Tire Carrier # TR-2 Work on Jay Feather Rear Bumper
  • If the bumper is 4 inch by 4 inch, continously welded and Jayco states it has the capacity to hold a spare tire carrier the Bumper Mount Tire Carrier part # TR-2 will fit and work well.
    view full answer...